Alcatel IP2015 Manuale utente

Home

PBXware

SERVERware

TELCOware

SIPmon

SIPProt

Desktop & Mobile

BRM

UADs

Appliances

EOL

From Bicom Systems Wiki

Contents

1 Introduction

■

2 Requirements

■

2.1 Identifying phone model

■

2.2 Phone firmware

■

2.3 DHCP server

■

2.4 PBXware version

■

3 Installation

■

3.1 Power adapter

■

3.2 Power over Ethernet (PoE)

■

3.3 Find the phone IP address

■

3.4 Reset to factory settings

■

4 Registering phone

■

4.1 Manual configuration

■

4.2 Auto Provisioning

■

Introduction

This Configuration Guide is written as general guide on how to configure the Alcatel phone

model IP2015 to work with PBXware 4.1.

Requirements

Identifying phone model

To start and successfully complete registration of your Alcatel phone you need to know which

phone model you will setup.

From the back of each Alcatel phone there are exact model information that you should check.

Although different phone models can have exactly the same requirements and installation

procedure, phone models can also have significantly different requirements and installation

procedure, so that ignorance of your own model may result in the inability to successfully set up

your phone.

Phone firmware

Make sure that your phone is loaded with appropriate firmware version,1.0.5b.

■

To find out the firmware version of your Alcatel phone model open a new browser window and

■

enter your phone IP address in order to access the phone web administration interface login

screen. Example: http://192.168.1.22.

■

factory default login details are username: admin and password: admin.

DHCP server

Fully configured and operational DHCP server.

PBXware version

PBXware version 4.1.2.0

In order to find out the PBXware version:

■

Navigate to Settings: About.

■

On the top of About page is a code similar to this one PBXware Edition: Business, Release:

4.1.2.0 (387597b7), Running: 1.8.32.1-gc-b47edc45, PBXware Proxy v4.1.2 (62b7bcd),

API: 4.1, libmemcached version: 1.0.14, where Release denotes the exact version of your

PBXware.

Installation

This chapter describes how to install and connect the phone to the electrical power and data

network as well as how to apply factory settings.

The following topics are covered:

Power adapter

■

Power over Ethernet (PoE)

■

Factory Settings

■

Power adapter

Connect the Network and Power

Connect the DC plug on the power adapter to the DC port on the phone and connect the other

■

end of the power adapter into an electrical power outlet.

Connect the ethernet cable between the Internet port on the phone and the network port on a

■

router or switch to access LAN.

NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter.

Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.

Power over Ethernet (PoE)

Connect the Network (only)

Using a regular ethernet cable, your phone can be powered from a Power over Ethernet (PoE)

compliant router or switch.

Connect the Ethernet cable between the Internet port on the phone and an available port on

■

the in-line power router or switch.

NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter.

Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.

Find the phone IP address

Find out your Alcatel phone IP Address.

Press ♫ button on the handset.

■

The IP address will be displayed on the top of display.

Reset to factory settings

This step is not required for brand new out-of-the-box phones, however, if the phone has been

already used then it is a must.

Open a new browser window and enter your phone IP address in order to access the phone

■

web administration interface login screen. Example: http://192.168.1.22.

■

factory default login details are username: admin and password: admin.

Click on Servicing tab.

■

Click Provisioning in the left navigation menu.

■

Click Reset button at the bottom of the page. Phone will be reset to the factory settings and

■

reboot.

Wait sometime prior for device to reboot.

■

NOTE: Do not unplug or remove power to the phone while it is updating firmware and

configurations.

Registering phone

This chapter describes how to identify Alcatel phone model, requirements that must be met and

how to register the phone using manual configuration or auto provisioning.

The following topics are covered:

Manual configuration

■

Auto provisioning

■

Manual configuration

This chapter describes how to set UAD settings, create PBXware extension and register the

phone.

The following topics are covered:

UAD settings

■

Creating extension

■

Registering phone

■

UAD Settings

UAD settings

Open a new browser window and enter the IP address in order to access the PBXware web

■

administration login screen. Example: http://192.168.1.10.

■

UAD settings

Navigate to Settings:UAD.

■

Make sure Alcatel UAD is enabled. To check the UAD status click on the edit icon

■

corresponding to your Alcatel phone.

Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.

■

Click on the Save button to save changes.

■

Creating extension

Creating Extension

Add Extension

Navigate to Extensions. Click on Add Extension.

■

The standard options window will be shown below.

■

Select Alcatel phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all extensions registered on the LAN and Remote is for all extensions

registered from remote networks, WAN, Internet etc.

Click on the Next step button.

■

Extension values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this extension. This e-mail address will receive all

system notification messages. Example: [email protected]

Department

■

Department to which extension will belong to. Example: Sales.

Click on the Save button.

■

Registering Phone

This chapter describes how to register Alcatel phone using Hostname or IP Address.

Hostname or IP Address

Open a new browser window and enter your phone IP address in order to access the phone

■

web administration interface login screen. Example: http://192.168.1.22

■

factory default login details are username: admin and password: admin.

Click on System.

■

Enter or set the following details into the respective fields.

■

REQUIRED FIELDS:

Enable account

■

Make sure the Check box is selected.

Display name

■

PBXware extension user name. Example: John

User Identifier

■

Usually the same number as the Authentication name.

Authentication name

■

PBXware extension number. Example 1003.

Authentication password

■

The Secret of the extension as received in the e-mail associated with this extension.

Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created

extension.

Server address (SIP server settings)

■

Enter the Hostname or IP Address of the PBXware.

- Example for Hostname: voip.bicomsystems.com

- Example for IP Address: 192.168.1.10

Click on the Save button at the bottom of the page.

■

If everything is done as above described, you should have successfully registered your phone

■

to PBXware. Dial *123 to verify registration.

Auto Provisioning

This chapter describes how to set UAD settings, create PBXware extension and register the

phone using DHCP or Static IP address.

The following topics are covered:

UAD Settings

■

Creating Extension

■

Registering Phone

■

UAD Settings

UAD settings

Open a new browser window and enter the IP address in order to access the PBXware web

■

administration login screen. Example: http://192.168.1.10.

■

UAD settings.

Navigate to Settings:UAD.

■

Make sure Alcatel UAD is enabled. To check the UAD status click on the edit icon

■

corresponding to your Alcatel phone.

Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.

■

Click on the Save button to save changes.

■

Creating Extension

Add Extension

Navigate to Extensions. Click on Add Extension.

■

The standard options window will be shown below.

■

Select Alcatel phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all extensions registered on the LAN and Remote is for all extensions

registered from remote networks, WAN, Internet etc.

Click on the Next step button.

■

Extension values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this extension. This e-mail address will receive all

system notification messages. Example: [email protected]

Auto Provisioning

■

Set to Yes.

MAC Address

■

Enter Alcatel phone MAC address. Example: 001565FF1536. MAC address can be found

at the back of the phone.

Click on the Save button.

■

Registering Phone

This chapter describes how to register Alcatel phone using DHCP, TFTP or HTTP & HTTPS.

DHCP

Configure DHCP

Make sure your DHCP router is configured to use option 66 to automatically instruct phones

■

with the URL for auto provisioning. For more information refer to your router documentation

or contact your network administrator.

Phone first boot or user initiated reboot

Auto provisioning process will start during phone first boot or after reboot process has been

■

initiated by user. DHCP server will instruct the phone where from to pickup appropriate

configuration file. If everything is done as above described, you should have successfully

registered your phone to PBXware. Dial *123 to verify registration.

TFTP or HTTP & HTTPS

Open a new browser window and enter your phone IP address, e.g. http://192.168.1.22.

■

Enter username and password and press Confirm button. NOTE: Factory default login

■

details are username: admin and password: admin.

Click on Servicing tab.

■

Click on Provisioning link in the left hand navigation menu.

■

Choose what server type you intend to use: HTTP, HTTPS and Trivial FTP. NOTE: Our

■

recommendation is to use the HTTP.

Enter http:// or https:// followed by Hostname or IP Address, followed then by

/prov in the Server provisioning string field.

Example for Hostname using HTTP: http://abc.bicomsystems.com/prov

Example for Hostname using HTTPS: https://abc.bicomsystems.com/prov

Example for IP Address using HTTP: http://192.168.1.10/prov

Example for IP Address USING HTTPS: https://192.168.1.10/prov

Enter Auto Provisioning username and password into Server authentication name and

■

Server authentication password fields.

If you choose to use TFTP enter tftp:// followed by Hostname or IP Address

Example for Hostname: https://voip.bicomsystems.com

Example for IP Address: tftp://192.168.1.10

Click on Save button at the bottom of the page.

■

Click on Reboot in the left navigation menu.

■

Click Reboot button.

■

A pop up window will show up, click on OK button to confirm your action.

■

You'll have to wait couple of seconds for the configuration to be updated. NOTE: Do not power

■

off your phone.

Altri manuali per IP2015

Indice

Altri manuali Alcatel Telefono IP

Alcatel

Alcatel Omni Office Manuale di istruzioni

Alcatel

Alcatel IP15 Manuale utente

Alcatel

Alcatel Advanced Reflexes Manuale utente

Alcatel

Alcatel First Reflexes Manuale utente

Alcatel

Alcatel Temporis IP901G Manuale utente

Alcatel

Alcatel OmniStack 8008 Manuale di istruzioni

Alcatel

Alcatel First Reflexes Manuale utente

Alcatel

Alcatel IP30 Manuale utente

Alcatel

Alcatel Temporis IP 600 Manuale utente

Alcatel

Alcatel 4029 Manuale utente

Alcatel

Alcatel Conference IP1850 Manuale utente

Alcatel

Alcatel 4028 Manuale utente

Alcatel

Alcatel TEMPORIS IP 200 Manuale di servizio

Alcatel

Alcatel EASY REFLEXES 4200 Istruzioni per il montaggio

Alcatel

Alcatel T30 Manuale utente

Alcatel

Alcatel Voice over WLAN (R1.1.1) Guida

Alcatel

Alcatel Omni Office Manuale di istruzioni

Alcatel

Alcatel IPTOUCH 600 Manuale utente

Alcatel

Alcatel SP-R5200 Come usare

Alcatel

Alcatel Omni Enterprise 8028 Manuale utente

Alcatel

Alcatel Alcatel 8 Series IPTouch 4068 Manuale utente

Alcatel

Alcatel Temporis IP901G Manuale utente

Alcatel

Alcatel Alcatel 8 Series IPTouch 4068 Manuale utente

Alcatel

Alcatel OmniPCX Enterprise 4018 Manuale utente

Manuali Telefono IP popolari di altre marche

Polycom

Polycom Polycom VVX 600 Manuale utente

Polycom

Polycom SoundPoint IP 450 Manuale utente

Cisco

Cisco SPA-500 Series Manuale utente

Polycom

Polycom SoundPoint IP 650 Manuale utente

Proximus

Proximus Maestro 3016 IP Manuale utente

Fanvil

Fanvil X4 Manuale utente

Cisco

Cisco 7962 Manuale utente

Snom

Snom 320 Manuale utente

Yealink

Yealink Yealink SIP-T46G Manuale utente

Avaya

Avaya 4625SW Manuale utente

Yealink

Yealink SIP-T52S Manuale utente

Nortel

Nortel 1140E Manuale utente

Nexotek

Nexotek NT-P500 Manuale utente

Avaya

Avaya Integral 5 R3.0 Manuale utente

GE 28320EE2 - Dect 6.0 InfoLink 2 Manuale utente

Avaya

Avaya 4600 Series Manuale di servizio

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Manuale utente

Nortel

Nortel i2050 Manuale utente