Aler AL200 Manuale utente

HD Vehicle MDVR

Declaration: The Alersec company has the right of final interpretation to this Guide.

Information contained herein is subject to change without prior notice due to continuous

improvement of the product and technology.

Quick Installation Guide

Table of Contents

1. Introduction.......................................................................................- 1 -

2. Preparations....................................................................................- 1 -

3.Power Connection...............................................................................- 2 -

4.Video Input Mode Setting..................................................................- 3 -

4.1 Camera Connection Mode........................................................- 3 -

4.2 Software Setting.......................................................................- 5 -

5.Online Setting .....................................................................................- 6 -

6.Introduction to Remote Control........................................................- 9 -

7.Usage Precautions.............................................................................- 10 -

- 1 -

1. Introduction

The MDVR adopts ARM DSP fast dual-core processor running on the Linux embedded OS,

and also integrates the most advanced H.264 video encoding/decoding in IT industry, 3G/4G

network, GPS and WiFi, as well ascircuit protection, HDD shock absorption, HDD heating,

operation at wide voltage rangefeatures. It is characterized by strong functionality, good

scalability, good stability and high performance cost and extensively applied in public buses,

logistics vehicles, school buses, police cars, financial convoy cars and fuel tankers.

2. Preparations

Figure 1 Physical Figure and Dimension Diagram

To turn the key anticlockwise to unlock the electronic lock and open the front cover, and

install HDD/SD card and SIM card in turns;

To install GPS, WiFi and 3G/4G antenna depending on the product configuration;

To select the position where the camera will be installed and arrange proper wiringto

connect it to the Mobile DVR;

To select a display and connect it to the video outputportof the MDVR.

- 2 -

1. To turn the electronic lock clockwise to lock it after HDD/SD card and SIM card

are installed; otherwise, the device will not be powered on;

2. To ensure prolonged and stable operation, it is advised to have the device

horizontally installed and take waterproof measures;

3.It is recommended to install 3G/4G, GPS and WiFi antennas in a place where it

will not be blocked signal or be able to receive strong signal;

4.This product has 8 channels of alarm inputs, 1 channels of alarm output, one

RS485, and two RS232 extended externalports which allow connection

toappropriate devices according to requirements of vehicles;

3. Power Connection

To connect the yellow cable of the power cord to ACC, the control circuit switch of the

vehicle, and the red and black ones are respectively connected to positive and negative electrode

of the vehicle power supply and then to vehicle MDVR. When testing the wiring condition,

twisting the red cable and yellow cable together and connect to the positive electrode, while the

black one is connected to the negative electrode.

Figure 2 Power Wiring Diagram

It is suggested that the MDVR power cable to be directly connected to the positive and negative

terminals of the vehicle battery cell (or the vehicle battery cell with fuse box). DO NOT connect

the MDVR power cable to any metal conductor subjects of the vehicle, which may influence

normal operation of the MDVR due to negative pulse; The power cable used for positive and

negative terminals shall have diameter of φ1.5mm or above.

- 3 -

4. Video Input Mode Setting

This product is a hybrid HD vehicle MDVR allowing connection with various types of

cameras. Table 1 shows portdefinitions of analog cameras. The IP camera port is standard port. A

user shall select camera type according to hardware connection port and configure proper

settingsin the software.

Connection

Diagram

Number

Interface

Definition

Connection

Diagram

Number

Interface

Definition

Number

Interface

Definition

12V OUT

A-IN-2

GND

V-IN-2

A-IN

A-IN-1

V-IN

V-IN-1

Table 1 Air Interface Definition

4.1 Camera Connection Mode

Connection

Mode

Connection Diagram

Model AL200-HYBRID

Connection of

analog camera

3 1

4 2

4channels of D1/960H/720PAHD video

inputs

2 channels of 720p AHD（1&2 CH）

+2*960H （3&4 CH）analog hybrid video

inputs

Connection ofIP

camera

4 channels of 720P/1080P IPC video inputs

Hybridconnection

of analog and IP

camera

4 channels of IPC+4*720PAHD/960H/D1

HD hybrid video inputs

Table 2 AL200-HYBRID Connection Mode

Connection Mode

Connection Diagram

Model AL300 -HYBRID

Connection of

analog camera

8 channels of CIF/ D1/960H analog video

inputs

- 4 -

Connection ofIP

camera

4 channels of 720P/1080P IPC video inputs

Hybridconnection

of analog and IP

camera

4 channels of 720P IPC+8*960H/D1/CIF

HD hybrid video inputs

Table AL300-HYBRID Connection Mode

Connection

Mode

Connection Diagram

Model AL2000-HD

Connection of

analog camera

3 1

4 2

4 channels of D1/960H/720PAHD video

inputs

2 channels of 720p AHD（1&2 CH）

+2*960H （3&4 CH）analog hybrid video

inputs

Hybrid

connection of

analog and IP

camera

1channels of 720P/1080P

IPC+4*720PAHD/960H/D1 HD video

inputs,connection to an external switch is

also acceptable.

Table 4 AL2000-HD Connection Mode

Connection Mode

Connection Diagram

Model AL3000-HD

Connection of

analog camera

8 channels of CIF/ D1/960H analog video

inputs

Hybrid connection

of analog and IP

camera

1channels of 720P/1080P

IPC+8*960H/D1/CIF HD hybrid video

inputs,connection to an external switch is

also acceptable.

Table 5 AL3000HD Connection Mode

Connection

Mode

Connection Diagram

Model AH100-HD

Connection of

analog camera

3 1

4 2

4 channels of D1/960H/720PAHD video

inputs

2 channels of 720p AHD（1&2 CH）

+2*960H（3&4 CH）analog hybrid video

inputs

Hybrid

connection of

analog and IP

camera

Max. 4 channels of 960H video inputs +

1 channel of 1080P IPC HD video input,

connection to an external switch is also

acceptable.

Table 6 AH100-HD Connection Model

- 5 -

Notice ,when connect 4channel 720P AHD cameras or 4*960H+1*1080P IPC camera ,need to

use High speed SD card（4K card，speed more than 80M/S）

4.2 Software Setting

After connecting the camera according to above connection

methods, from the Setup menu →Channel Mode interface, select

the desired connection mode and save it and the system will

automatically restart. Then, from the Setup menu →Record Setup

→Main Stream and IPC setting, where you can set video resolution,

frame rate, picture quality, audio recording and IP address for each

channel (Following figures show JH4-HYBRID setting interface.

Settings for the 8 channelsMDVR are similar).

After Channel Mode is selected, the MDVR will automatically restart and enter the related setting

interface. IPC setting is not available if only an analog camera is connected.

- 6 -

Figure 3 AL3000 HD Setting Interface

When adding a camera, select the related channel and you can manually input the IP address

and port number of the IP camera, or click "Search" to select the desired IP camera in the search

result. The user name and password are set for the IP camera. For a IP camera with security

feature, the setting shall be the same as that for the IP camera itself; or this setting can be ignored.

Use remote control to move to the letter you want, press "Enter" to confirm your selection and

press "Return" to return and complete your input.

5. Online Setting

When uploading your device to the server via 3G/4G network, you shall set the device

number, vehicle number, server IP and the wireless network before you can remotely manage it

via remote CMS/IVMS client.

1. Press the "LOGIN" key on the remote control, and input the initial password 888888. From the

Setup menu →General →Vehicle Info, complete the device number and related vehicle number.

Other information can be filled in as necessary. Only when the mileage statistic is enabled can

you count the mileage in the server client;

- 7 -

Figure 4 Vehicle Information Setting Interface

2.。

2.Return to the Basic Setup interface and enter the Network interface to set the server IP address

and control port, by default, 6608; When an external IP camera is connected, you shall set the IP

address of the RJ45 port, with its network segment same as that of IP address of the IP camera. In

addition, set the IP address of the gateway server as the first IP address in this network segment

(e.g. 192.168.000.001, being the first IP in network segment 0).

Figure 5 Network Setting Interface

Usercan choose to either establish its own server or use a server provided by the MDVR

manufacturer. Please contact the MDVR manufacturer for technical support who will provide

and assign the device number, server IP and user name & password of the client to the user. The

user would simply fill provided information into the vehicle MDVR and can manage the related

vehicle via the serverclient.

3. Return to Setup menu → Peripheral Setup → Wireless Setup, and select the network type

corresponding to your SIM card (the following figure shows the difference between 3G and 4G

Please ensure your device number is unique which

will be used by the remote server to monitor and

manage your vehicle.

Please ensure your vehicle number is correct

which will be superimposed on the video.

- 8 -

software). Fill in the access point name (APN), center number, user name and password provided

by your operator; select the network type. For Chinese operators, select AUTO. For international

subscribers, fill in the information provided by your local mobile operator.

Figure 6 Wireless Setup Interface

4. On the monitoring screen, press the "INFO" key on the remote control to check the connection

status and ensure that connected devices such as 3G/4G, GPS and WiFi work normally, and that

the vehicle device is successfully connected to the server center.

Figure 7 System Information Query Interface

车After MDVR settings are completed, you can go to the server to add the related vehicle

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Aler Registratore digitale

Aler

Aler AH2000 Manuale utente

Manuali Registratore digitale popolari di altre marche

FLIR

FLIR M3100E Series Manuale utente

VTRACKPRO

VTRACKPRO FPRO300 Manuale utente

Swann

Swann NVR-7085 models Manuale utente

XtendLan

XtendLan DVR-1670C Manuale utente

urmet domus

urmet domus 1093/004AHD Manuale utente

Holux

Holux M1 Manuale utente

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuale utente

Whistler

Whistler D16VRS Manuale utente

Defender Security

Defender Security 82-20235 Manuale utente

MISUMI

MISUMI MP-WF100M Manuale utente

Speco

Speco D8HU Manuale utente

UST

UST DDR-E04AA Istruzioni per l’uso

Consolidated

Consolidated Digital Video Recorder Manuale utente

Mace

Mace DVR0404RW Guida rapida

RCA

RCA RTD315W Manuale utente

FSM

FSM Colibri Grande PRO Manuale utente

Hauppauge

Hauppauge HD PVR 2 Manuale utente

Identivision

Identivision ICR-PH161i PIONEER Manuale utente