Algo 4900 Manuale utente
4900 USB ATA
Analog Terminal Adapter for the
Nortel IP Softphone 2050
User Guide
Algo Communication Products Ltd.
www.algosolutions.com
DC4900-UG-11
2 4900 USB Analog Terminal Adapter
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: 1) Reorient or relocate the receiving antenna, 2) Increase the separation
between the equipment and receiver, 3) Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected, or 4) Consult the dealer or an experienced
radio/TV technician for help.
Copyright © 2007 Algo Communication Products Ltd. All Rights
Reserved.
Algo®is a registered trademark of Algo Communication Products Ltd. All
other trademarks are the property of their respective owners.
Document #DC4900UG-11; 24-January-2007
4900 USB Analog Terminal Adapter
User Guide 3
Table of Contents
Introduction..............................................................................4
Features..................................................................................5
Applications............................................................................5
Typical Connection Diagram.................................................6
Package Contents...................................................................6
Connections............................................................................7
Installation................................................................................7
Troubleshooting .....................................................................8
Specifications..........................................................................11
Warranty and Repair.............................................................12
About Algo..............................................................................13
Contact Information.............................................................13
Sales .....................................................................................14
Product Registration ............................................................14
Related Products ....................................................................16
4 4900 USB Analog Terminal Adapter
Introduction
Algo’s USB Analog Terminal Adapter enables the
use of a traditional analog wired or cordless
telephone, TTY/TDD terminal, fax machine (refer to
footnote on page 5), or other analog device with a
Nortel IP Softphone 2050 (Version 2 B254 or newer)
for Business Communication Manager (BCM) or
Communication Server 1000 (CS 1000).
Ring voltage and Caller Line Identification are
provided for inbound calls to the 2050 and outbound
calls are easily made with DTMF (touch-tone)
dialing. The USB ATA is powered entirely by the host
PC’s USB port to minimize cords and connections.
The USB ATA conforms to all relevant Windows Plug
& Play specifications making installation fast and
simple.
4900 USB Analog Terminal Adapter
User Guide 5
Features
•USB Powered
•Two wire RJ11 Telephone jack for connecting
analog telephone
•Output for optional external alerter (message
waiting and ring notification)
•Call Display conversion from 2050 window
Applications
•Traditional wired analog telephone
•Cordless telephones for greater mobility
when away from desk
•Fax machines1
•Conference/Speaker telephones
•Analog telephone system trunk connection
•TTY/TDD terminals for hearing impaired
1Fax functionality requires G.711 Codec (no T.38 Support). Fax
performance may vary with PC and network capability. For this reason,
Algo does not recommend the USB Analog Terminal Adapter for
frequent multi-page fax traffic. Some PCs may require settings to
improve audio performance necessary for fax applications. Please visit
www.algosolutions.com/4900 for more information.
6 4900 USB Analog Terminal Adapter
Typical Connection Diagram
Package Contents
•4900 USB Analog Terminal Adapter
•User Guide
•6 ft (1.8m) USB Cable
4900 USB Analog Terminal Adapter
User Guide 7
Connections
Installation
1. Connect the 4900 USB ATA to the PC using
the supplied USB cable.
2. The first time the USB ATA is plugged in,
there will be a pause while Windows
configures the device and locates the
appropriate driver software. During the
installation there may be a prompt to supply
the original Windows CD ROM so that
Windows can locate the drivers.
8 4900 USB Analog Terminal Adapter
3. In the IP Softphone 2050 Settings tool, select
the section for “Sound Devices” and select
“USB Audio Device” for both the Microphone
and Speaker options under “Headset or
Handset Device”.
4. Start the IP Softphone.
Troubleshooting
If the USB ATA is not functioning correctly, please try
the following in order:
1. Verify that you have Windows 2000 or
Windows XP. This can be done by clicking on
My Computer and selecting Properties.
2. Check that “Universal Serial Bus controllers”
appears in the Windows Device Manager. If it
does not appear, confirm USB is enabled in
your computer’s setup menus.
3. Check that “USB Audio Device” appears
under “Sound, video and game controllers” in
the Windows Device Manager. If it does not,
and the above conditions are correct, then
see the troubleshooting section under USB in
Windows Help.
4900 USB Analog Terminal Adapter
User Guide 9
Other steps you can take to verify proper operation
of the 4900:
Check Equipment and Connections
Lift the handset or go off-hook on your Telephone or
device. Verify that IP Softphone 2050 indicates off-
hook as well. If it does not, check the following:
•Telephone is properly connected to ATA via
Telephone cable
•ATA is properly connected to PC via USB
cable
•If USB Hub is used, ensure that the Hub is
line powered (ATA is a high power device
that requires 500mA)
•IP Softphone 2050 version meets minimum
requirements: Version 2 B254
•IP Softphone 2050 is successfully connected
to server and can go off-hook using the 2050
interface instead of the ATA
•Telephone is functional (try connecting to
standard analog line instead)
10 4900 USB Analog Terminal Adapter
Check for Dial Tone
Lift the handset on your Telephone and listen for dial
tone. If there is none, check the following:
•IP Softphone 2050 indicates off-hook state
•Audio settings in the IP Softphone 2050 are
correct
Check Dialing
Lift the handset on your telephone and dial an
extension. The digits dialed should appear in the IP
Softphone 2050 Window and the dialed telephone
should ring. If not, check the following:
•IP Softphone 2050 indicates off-hook state
•Telephone is set to tone dialing (not pulse).
You should hear the tones in the handset of
the telephone when dialing
•Dial using the IP Softphone 2050 keypad
instead. If this does not work, verify that the
telephone number that you are trying to dial is
correct
Connect with another Telephone
Make a call to another Telephone. Verify that you
can hear the other party, and that they can hear you.
If this does not work, check that the audio settings in
the IP Softphone 2050 are correct.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Algo Adattatore
