Algo 8028 Manuale utente
8028 SIP Doorphone (G2) FW 3.2
8028 SIP Doorphone (G2)
FW Version 3.2
User Guide
Order Codes
8028 SIP Doorphone (G2)
Optional Accessories:
64-00038 Brass Faceplate
X24VG Power Suppl
Document 90-00104
05/21/2020
Page 1
Algo Communication Products Ltd
4500 Beedie St Burnab BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8028 SIP Doorphone (G2) FW 3.2
Table o Contents
IMPORTANT SAFETY INFORMATION......................................................................................................3
OVERVIEW................................................................................................................................................. 7
INTRODUCTION................................................................................................................................................... 7
WHAT’S NEW (COMPARED TO THE ORIGINAL 8028)................................................................................................... 8
APPLICATIONS.................................................................................................................................................... 8
SETUP AND INSTALLATION................................................................................................................... 10
GETTING STARTED - QUICK INSTALL & TEST............................................................................................................ 10
INSTALLATION.................................................................................................................................................. 12
PROGRAMMING AND CON IGURATION................................................................................................................... 14
DOOR OR GATE CONTROL BASICS......................................................................................................................... 14
PRE-WIRING INSTRUCTIONS................................................................................................................................ 15
WIRING CONNECTIONS (CONTROLLER)................................................................................................................... 16
WIRING CONNECTIONS (DOOR STATION)................................................................................................................ 16
LED INDICATORS............................................................................................................................................... 17
RESET............................................................................................................................................................. 18
TLS OR SIP SIGNALING AND PROVISIONING........................................................................................................... 19
WEB INTERFACE STATUS AND LOGIN.................................................................................................22
WEB INTER ACE LOGIN....................................................................................................................................... 22
STATUS........................................................................................................................................................... 23
WEB INTERFACE BASIC SETTINGS......................................................................................................24
BASIC SETTINGS TAB – SIP.................................................................................................................................. 24
BASIC SETTINGS TAB – EATURES......................................................................................................................... 25
BASIC SETTINGS TAB – DOOR CONTROL................................................................................................................. 27
BASIC SETTINGS TAB – INPUT/OUTPUT.................................................................................................................. 29
BASIC SETTINGS TAB – MULTICAST....................................................................................................................... 31
WEB INTERFACE ADVANCED SETTINGS.............................................................................................34
ADVANCED SETTINGS TAB - NETWORK................................................................................................................... 34
ADVANCED SETTINGS TAB – ADMIN...................................................................................................................... 36
ADVANCED SETTINGS TAB – TIME......................................................................................................................... 39
ADVANCED SETTINGS TAB – PROVISIONING............................................................................................................. 40
ADVANCED SETTINGS TAB – ADVANCED AUDIO....................................................................................................... 42
ADVANCED SETTINGS TAB – ADVANCED SIP........................................................................................................... 44
ADVANCED SETTINGS TAB – ADVANCED MULTICAST................................................................................................. 47
WEB INTERFACE SYSTEM..................................................................................................................... 49
SYSTEM TAB - MAINTENANCE.............................................................................................................................. 49
SYSTEM TAB - IRMWARE................................................................................................................................... 50
SYSTEM TAB - ILE MANAGER.............................................................................................................................. 51
SYSTEM TAB – TONES........................................................................................................................................ 52
SYSTEM TAB – SYSTEM LOG................................................................................................................................ 52
SPECIFICATIONS..................................................................................................................................... 53
FCC COMPLIANCE STATEMENT............................................................................................................54
Document 90-00104
05/21/2020
Page 2
Algo Communication Products Ltd
4500 Beedie St Burnab BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8028 SIP Doorphone (G2) FW 3.2
Important Sa ety In ormation
The 8028 SIP Doorphone (G2) is designed, tested and verified to compl with CSA/ANSI/UL
62368-1 Safet Standards for INFORMATION TECHNOLOGY EQUIPMENT.
Important Sa ety In ormation
This product is powered b a certified limited power source (LPS), Power over Ethernet
(PoE); through CAT5 or CAT6 connection wiring to an IEEE 802.3at PoE+ or 802.3af
compliant network PoE switch. The product is intended for installation indoors. All wiring
connections to the product must be in the same building. If the product is installed be ond
the building perimeter or used in an inter-building application, the wiring connections must
be protected against over voltage / transient. Algo recommends that this product be
installed b a qualified electrician.
If ou are unable to understand the English language safet information then please
contact Algo b email for assistance before attempting an installation
Consignes de Sécurité Importantes
Ce produit est alimenté par une source d’alimentation limitée certifiée (alimentation par
Ethernet); des câbles de catégorie 5 et 6 joignent un commutateur réseau à alimentation
par Ethernet homologué IEEE 802.3at PoE+ or 802.3af. Le produit est conçu pour être
installé à l’intérieur. Tout le câblage rattaché au produit doit se trouver dans le même
édifice. Si le produit est installé au-delà du périmètre de l’édifice ou utilisé pour plusieurs
édifices, le câblage doit être protégé des surtensions transitoires. Algo recommande qu’un
électricien qualifié se charge de l’installation de ce produit.
Si vous ne pouvez comprendre les consignes de sécurité en anglais, veuillez
communiquer avec Algo par courriel avant d’entreprendre l’installation au
In ormación de Seguridad Importante
Este producto funciona con una fuente de alimentación limitada (Limited Power Source,
LPS) certificada, Alimentación a través de Ethernet (Power over Ethernet, PoE);
medianteun cable de conexión CAT5 o CAT6 a un conmutador de red con PoE en
cumplimiento con IEEE802.3at PoE+ or 802.3af. El producto se debe instalar en lugares
cerrados. Todas las conexiones cableadas al producto deben estar en el mismo edificio.
Si el producto se instala fuera del perímetro del edificio o se utiliza en una aplicación en
varios edificios, las conexiones cableadas se deben proteger contra sobretensión o
corriente transitoria. Algo recomienda que la instalación de este producto la realice un
electricista calificado.
Document 90-00104
05/21/2020
Page 3
Algo Communication Products Ltd
4500 Beedie St Burnab BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8028 SIP Doorphone (G2) FW 3.2
Si usted no puede comprender la información de seguridad en inglés, comuníquese con
Algo por correo electrónico para obtener asistencia antes de intentar instalarlo:
Wichtige Sicherheitsin ormationen
Dieses Produkt wird durch eine zertifizierte Stromquelle mit begrenzter Leistung (LPS –
Limited Power Source) betrieben. Die Stromversorgung erfolgt über Ethernet (PoE –
Power over Ethernet). Dies geschieht durch eine Cat-5-Verbindung oder eine Cat-6-
Verbindung zu einer IEEE 802.3at PoE+ or 802.3af-konformen Ethernet-Netzwerkweiche.
Das Produkt wurde konzipiert für die Installation innerhalb eines Gebäudes. Alle
Kabelverbindungen zum Produkt müssen im selben Gebäude bestehen. Wenn das
Produkt jenseits des Gebäudes oder für mehrere Gebäude genutzt wird, müssen die
Kabelverbindungen vor Überspannung und Spannungssprüngen geschützt werden. Algo
empfiehlt das Produkt von einem qualifizierten Elektriker installieren zu lassenv.
Sollten Sie die englischen Sicherheitsinformationen nicht verstehen, kontaktieren Sie bitte
Algo per Email bevor Sie mit der Installation beginnen, um Unterstützung zu erhalten.
Algo kann unter der folgenden E-Mail-Adresse erreicht werden:
安全须知
本产品由认证的受限电源（LPS），以太网供以太网供电（PoE），以太网供通过 CAT5 或
CAT6 线路联接至 IEEE 802.3at PoE+ or 802.3af 兼容的 PoE 网络交换 供电。本产品适用
于室内或建筑物周边安装。所有联接本产品的线路必须源自同一建筑物。本产品如需用于
超出建筑物周边范围或跨建筑物的安装，以太网供线路联接部分必须有过压和瞬态保
护。Algo 建议本产品由专业电工安装。
如果您对理解英文版安全须知有问题，安装前请通过电子邮件和 Algo 联
Document 90-00104
05/21/2020
Page 4
Algo Communication Products Ltd
4500 Beedie St Burnab BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8028 SIP Doorphone (G2) FW 3.2
INSTALLATION
EARTH GROUNDING MAY BE REQUIRED
This guide provides important safety information which should be read thoroughly before
permanently installing the product. Earth grounding is required for installations with door
station wiring that leaves the perimeter of a building due to the potential for over-voltage
fault conditions.
Note that this requirement does not appl when a door station is installed indoors
or on the outside wall of a building if the wiring runs directl into the building.
Earth grounding can be achieved by connecting the 8028 ( 2) control unit power jack to
earth ground using either the supplied ground strap directly to a suitable ground point or
by use of the optional Algo 75-00004 24Vdc Power Adapter to socket outlet with a
protective earthing connection.
It is highly recommended that when an earth ground is required the control unit be
located in a restricted area and that the control unit be secured in place and cable ties
used to prevent accidental disconnect of the connection to earth ground. This connection
should be verified by a qualified electrician and routinely check as a safety precaution.
Under no circumstances can the Control Unit be disconnected from earth ground
while connected to outdoor wiring.
EMERGENCY COMMUNICATION
If used in an emergenc communication application, the 8028 SIP Doorphone (G2) should
be routinel tested. SNMP supervision is recommended for assurance of proper
operation. Contact Algo for other methods of operational assurance.
WET OR OUTDOOR ENVIRONMENTS
The 8028 SIP Doorphone’s controller is intended for indoor locations with the Door Station
is intended for outdoor locations and ma be subjected to spra or weather, provided the
rear wiring cavit is properl sealed to prevent water ingress.
Gaskets included with the Door Station ma be effective against water ingress on some,
but not all surfaces in which case additional protective measures must be taken such as a
perimeter sealant.
CAT5 or CAT6 connection wiring to an IEEE 802.3a or IEEE 802.3at compliant
network PoE/PoE+ switch must not leave the building perimeter without adequate
lightning protection.
When the Intercom is connected to wiring that exits the building, there is potential
risk o lightning induced electrical surges or high voltages rom ault conditions. To
reduce risk, outdoor wiring should be protected by Earth grounded conduit
whenever possible. Relay input and output connections must not leave the building
Document 90-00104
05/21/2020
Page 5
Algo Communication Products Ltd
4500 Beedie St Burnab BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8028 SIP Doorphone (G2) FW 3.2
perimeter without adequate lightning protection. Please see in ormation in
‘Installation’ section above.
Document 90-00104
05/21/2020
Page 6
Algo Communication Products Ltd
4500 Beedie St Burnab BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8028 SIP Doorphone (G2) FW 3.2
Overview
Introduction
Ideal for secure business entrances, emergenc intercom, and residential gates, Algo’s
8028 SIP Doorphone (G2) provides hands-free intercom capabilit , entrance securit with
door unlock control, rugged weatherproof design, and superior audio performance.
Full compatible with SIP industr standards, the SIP Doorphone will work with most
hosted or enterprise SIP-based servers supporting third-part SIP endpoints.
The 8028 is a two component product for eas installation into existing construction
utilizing existing intercom wiring at the door. No network connectivit is required at the
outdoor intercom and the door rela connection is located safel indoors. The “Control
Unit” must be installed in a dr indoor location. The “Door Station” ma be located indoors
or outdoors and is connected to the control unit with a single twisted pair wire (t picall
24AWG) up to 1,000 feet (300 m) in length. The single wire pair carries low voltage power
and digital communication in both directions as well as connectivit supervision.
What is Included
•8028 SIP Doorphone (G2) “Control Unit”
•Outdoor rated digital “Door Station” (model 3201) with Stainless Steel Faceplate
•Outdoor rated surface mount bezel & gasket kit for door station
•Wall mount bracket for control unit
•Network Cable 6ft (2m)
•Earth Grounding Strap
•2x terminal blocks (one 5-pin connector, one 6-pin connector)
•Flat head screwdriver
•Getting Started Sheet
What is not Included
•Optional 24V DC Power Suppl (Order code 75-00004)
•Ph sical Door Sensor
•Door Strike
•Door Strike Power Suppl
Document 90-00104
05/21/2020
Page 7
Algo Communication Products Ltd
4500 Beedie St Burnab BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8028 SIP Doorphone (G2) FW 3.2
What’s New (compared to the original 8028)
The 8028 SIP Doorphone (G2) is the next generation of the popular Algo 8028. The
doorphone has upgraded hardware capable of running the latest securit and encr ption
standards, including TLS & SRTP, ensuring secure communication with hosted SIP
providers.
Designed to include all the features of the original 8028, the second generation has a
number of new features such as PoE/PoE+ power input, and built-in terminal block.
As the device now runs on a new hardware platform, note that the firmware files are
different compared to the original 8028. For assistance migrating provisioning files for this
new device, please contact Algo support.
Applications
Typical Applications or Auxiliary Inputs and Outputs
The 8028 architecture and digital link between the Door Station and Controller provides
flexible options using the auxiliar inputs and outputs. These are some t pical
applications.
Hands- ree Visitor Communication and Door/Gate Control
Visitors press the call button on the 8028 intercom station to initiate calling to a configured
extension such as a securit desk or hunt group. Answering the intercom call enables two-
wa communication with the visitor. During the intercom call the telephone ke pad can be
used to enter a door open code (e.g. digit 6, or up to four digits). Once activated the 8028
access control rela will permit a momentar unlock of the entrance for the visitor to gain
access through the door or gate in a secure and efficient manner.
Cancel Ring When Door Opened
In a residential or warehouse installation it is not uncommon for the door to be answered
in person before the phone is answered. Either Door Station or Controller inputs can be
configured to cancel ring if the door is opened before a call is answered. This requires a
normall closed or normall open contact to detect door open (not included).
Trigger Door Bell rom Door Station
When the Door Station call button is pressed, either (or both) the Door Station or Controller dr
contact output can be configured to activate a door bell or auxiliar alerting s stem in addition to
phone ring.
Trigger Door Station rom External Button/Event
Either the Controller or Door Station can accept a dr contact closure to activate the
Doorphone as if the call button had been pressed. This could be an external doorbell
button, PIR detector, or some other s stem.
Document 90-00104
05/21/2020
Page 8
Algo Communication Products Ltd
4500 Beedie St Burnab BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8028 SIP Doorphone (G2) FW 3.2
Cancel Door Open Relay once Door Opened
The door opening control can be set for activation (using the ‘Open Code’) up to 30
seconds (set b the ‘Rela Time’ setting) to allow sufficient time for entr . For securit , the
8028 can be configured to cancel Door Opening once the door is opened to prevent
“tailgating” b unauthorized personnel.
Unlock Door Inde initely until Cancelled
The door opening control can be set to unlock indefinitel (using the ‘Latch Open Code’)
until cancelled (using the ‘Release Code’) that locks it again. This allows an entrance to
be used repeatedl for a period of time without requiring multiple activations of the door
control rela .
Anti-Door Tamper
A feature of the 8028 is to ring the telephone(s) with a warning alert in the event a door is
ajar due to tampering (such as a door blocked open after being legitimatel released for a
visitor). Requires ph sical door sensor (not included).
In-Use and Ring
Either the Controller or Door Station can be configured to provide a dr contact output
during ring or in-use for channel selection (t picall ) of third part video monitoring
s stems.
Document 90-00104
05/21/2020
Page 9
Algo Communication Products Ltd
4500 Beedie St Burnab BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
8028 SIP Doorphone (G2) FW 3.2
Setup and Installation
Getting Started - Quick Install & Test
This guide provides important safety information which should be read thoroughly
before permanently installing the product. Earth grounding is required for
installations with door station wiring that leaves the perimeter of a building
due to the potential for over-voltage fault conditions.
Note that this requirement does not appl when a door station is installed
indoors or on the outside wall of a building if the wiring runs directl into
the building.
1. If earth grounding is required (read safet caution above) then make that connection first
before connecting the control unit to the network or door station.
2. Flush or surface-mount the Digital Door Station at desired location and connect the
“CTRL” terminals of the Door Station to the Control Unit pluggable terminal block
positions indicated b the door station icon ( ). Note that a ellow caution sticker must
first be removed from the Control Unit pluggable terminal socket.
3. Connect the 8028 (G2) Control Unit to a network port. If the network switch supports
PoE (IEEE 802.3af 15W) or PoE+ (IEEE 802.3at 30W) then the control unit will power
up as indicated b the blue power light on the front. If the network switch does not
provide PoE then a PoE injector ma be used or the optional Algo 75-00004 24Vdc
Power Adapter.
4. The red LED illuminated call button on the front of Door Station will turn on. After about
30 seconds, a beep will signal the completion of the boot process.
5. After the boot is complete, press the call button on the Door Station to hear the IP
address. (Once the SIP Server field is populated in the 8028 web interface, the call
button will contact the preconfigured extension when pressed.) The IP address ma also
be discovered b momentaril pushing the reset button next to the RJ45 jack or
downloading the Algo locator tool to find Algo devices on our network:
www.algosolutions.com/locator
6. Access the 8028 SIP Doorphone web page b entering the IP address into a browser
(Chrome, Firefox or Edge) and login using the default password algo .
7. Enter the IP address or the name for the SIP server into the SIP Domain field under the
BASIC SETTINGS > SIP tab.
8. Enter the SIP Extension, Authentication ID, and Password. Also enter the target Dialing
Extension that the Intercom will call.
Note: The Authentication ID may also be called Username for some SIP servers, and in
some cases may be the same as the SIP extension.
Document 90-00104
05/21/2020
Page 10
Algo Communication Products Ltd
4500 Beedie St Burnab BC Canada V5J 5L2
www.algosolutions.com
(604) 454-3792
Altri manuali per 8028
2
Indice
Altri manuali Algo Sistema di interfono
Algo
Algo 8039 Manuale utente
Algo
Algo 8036 Manuale utente
Algo
Algo 8028 Istruzioni operative e di manutenzione
Algo
Algo 3228 Station Port FXS Manuale utente
Algo
Algo 3226 Manuale utente
Algo
Algo 8201 Manuale utente
Algo
Algo 8028 SIP Doorphone Manuale utente
Algo
Algo 8036 Manuale utente
Algo
Algo 3026 Manuale utente
Algo
Algo 3008 Manuale utente
