Allegro Packets Network Multimeter 1500 Manuale utente

Installation Guide

Allegro Network Multimeter 1500, 3500 and 5500

Default Settings

LAN: DHCP client

Wi-Fi SSID: allegro-mm-(see top label)

Wi-Fi URL: https://allegro/ or

https://192.168.4.1

Wi-Fi WPA2 key: Allegro-MM

Web interface user name: admin

Web interface password: allegro

Overview

1. Package Contents

2. Hardware Deployment

3. Device Start

4. Management Interface Conguration

5. Conguration Reset

6. Firmware Update Notication

7. Factory Reset

8. Manual

1. Package Contents

1 x Allegro Network Multimeter 1500, 3500 or

5500 incl. redundant power supply unit

2x Power cable

1 x Rack rail set

1 x Wi-Fi USB adapter (already pre-installed)

The Allegro Network Multimeter package contains the following items:

1 x Screw set for HDDs

1 x Screw set for rack rail set

36 x 3.5“ HDD mounting frame

1 x Installation guide

The guide contains the following sections:

Please send an email to support@allegro-packets.com or call +49 341 59 16 43 54.

6. Firmware Update Notication

Update information via email

With each release, Allegro Packets will send you an email with release notes and a link to down-

load the update. If you want to be added to this mailing list, please send an email with your serial

number (‘Info‘  ‘System Info‘  ‘System ID’) to support@allegro-packets.com and the subject

‘Release’.

Using the Allegro web interface

Start your Allegro Network Multimeter and click ‘Settings’ on the left side of the menu and then

‘Firmware updates’. Click on ‘Check for new rmware’ and the Allegro Network Multimeter will

tell you if a new version is available for download. If so, you can choose to download it directly to

the device. In addition, this page provides an overview of all versions available to you. To start the

new version, click on ‘Activate’.

7. Factory Reset

The ‘Factory reset‘ will clear the entire system installation and restore the rmware to the ver-

sion that was originally shipped with the Allegro Network Multimeter.

1. Power o the Allegro 1500, 3500 or 5500.

2. Remove all network cables from the device.

3. Connect a display to the VGA port.

4.Connect a USB keyboard to any of the four USB ports.

5. Power on the device by pressing the power button.

6.After initialization a boot menu appears. Select ‘Factory reset’ and press Enter. Or select

‘Conguration reset’ to reset the conguration settings only while keeping the current rm-

ware installation.

7. The device will boot, reset everything to factory settings, and reboot again.

8.The device is now reset to factory settings.

9. Disconnect the display and keyboard.

8. Manual

The device manual can be accessed from the web interface. Each web section contains a button

to access context-specic documentation, the complete manual can be opened by clicking on

the ‘Manual’ link in the menu.

Getting Help:

5. Conguration Reset

The ‘Conguration reset‘ restores the conguration to the default settings:

1. Web interface: Go to menu ‘Settings‘  ‘Administration’ and click on ‘Reset system congu-

ration’. All settings including the network conguration will be reset to factory default.

2.Boot menu: Follow the instruction in the section 7. Factory Reset.

You can nd more information and details via the allegro-packets.com/wiki.

2. Hardware Deployment

2.1. Management Access (Control Plane)

Step 1: Connect power supply

Step 2: Connect management LAN

Alternative: Insert Wi-Fi adapter to any

of the USB ports

By default, for LAN, the device will query an IP address via DHCP dynamically from your network.

By default, for Wi-Fi, the device will open an Access Point so smartphones, tablets, or laptops can

connect to the Access Point and access the web interface.

In case Wi-Fi access is not possible and no DHCP server exists, a temporary IP address can be as-

signed by using a USB keyboard and pressing ‘Shift+S’. The LAN IP interface is temporarily set to

192.168.0.1. If this is already taken, another address in the range from 192.168.0.1 to 192.168.0.10

will be used.

You can check the assigned IP address on a connected monitor.

2.2. Network Measurement Installation (Data Plane)

The x500 Series, consisting of the Allegro 1500, 3500 and 5500, analyzes all data traic trans-

mitted through all network interfaces of the built-in measurement cards. The Allegro Network

Multimeter can be equipped with up to 6 network cards with 2 or 4 ports each. The appliance

can be used in the following congurations:

2.2.1. Bridge Mode

Each 2 adjacent ports of a network card form a Layer 2 bridge, which forwards all incoming data

traic to the respective other partner port.

WARNING: Bridge mode is a software-only TAP and will not work in case of a device error or

after power o.

2.2.2. Sink Mode

Received packets will be processed but not forwarded. Connect the Allegro Network Multimeter

to a hardware TAP by connecting both TAP interfaces to the device. Alternatively, a switch or

router mirror port can be connected to any of the device network interfaces.

2.3 Installing your own HDDs

The Allegro x500 can be used with up to 36 x 3.5“ SATA/SAS HDDs. These must be installed in

the mounting frame.

3. Device Start

1. Press the power button at the front of the device. The device will boot within two minutes.

2.LAN access: The device gets its IP from the DHCP server in your network. Check the console

output on an attached monitor or ask the server administrator for the IP of the device, then

enter the IP into the URL bar of your web browser.

3.Wi-Fi access:

- SSID: allegro-mm-xxxx (individual per device)

- WPA2 password: Allegro-MM

- Enter https://allegro/ or https://192.168.4.1/ into the URL bar of a browser.

4.Web interface authentication:

- User name: admin

- Password: allegro

4. Management Interface Conguration

You can congure the management interfaces by accessing the web interface at ‘Settings‘

 ‘Management interface settings’. The available options are described in the online manual

which can be accessed via the web interface.

Default conguration is bridge mode, thus running as an inline device. The link mode can be

congured via a web interface (menu ‘Settings‘  ‘Global settings’):

Power supply MGMT LANMGMT WLAN

2. Hardware Deployment

2.1. Management Access (Control Plane)

Step 1: Connect power supply

Step 2: Connect management LAN

Alternative: Insert Wi-Fi adapter to any

of the USB ports

By default, for LAN, the device will query an IP address via DHCP dynamically from your network.

By default, for Wi-Fi, the device will open an Access Point so smartphones, tablets, or laptops can

connect to the Access Point and access the web interface.

In case Wi-Fi access is not possible and no DHCP server exists, a temporary IP address can be as-

signed by using a USB keyboard and pressing ‘Shift+S’. The LAN IP interface is temporarily set to

192.168.0.1. If this is already taken, another address in the range from 192.168.0.1 to 192.168.0.10

will be used.

You can check the assigned IP address on a connected monitor.

2.2. Network Measurement Installation (Data Plane)

The x500 Series, consisting of the Allegro 1500, 3500 and 5500, analyzes all data traic trans-

mitted through all network interfaces of the built-in measurement cards. The Allegro Network

Multimeter can be equipped with up to 6 network cards with 2 or 4 ports each. The appliance

can be used in the following congurations:

2.2.1. Bridge Mode

Each 2 adjacent ports of a network card form a Layer 2 bridge, which forwards all incoming data

traic to the respective other partner port.

WARNING: Bridge mode is a software-only TAP and will not work in case of a device error or

after power o.

2.2.2. Sink Mode

Received packets will be processed but not forwarded. Connect the Allegro Network Multimeter

to a hardware TAP by connecting both TAP interfaces to the device. Alternatively, a switch or

router mirror port can be connected to any of the device network interfaces.

2.3 Installing your own HDDs

The Allegro x500 can be used with up to 36 x 3.5“ SATA/SAS HDDs. These must be installed in

the mounting frame.

3. Device Start

1. Press the power button at the front of the device. The device will boot within two minutes.

2.LAN access: The device gets its IP from the DHCP server in your network. Check the console

output on an attached monitor or ask the server administrator for the IP of the device, then

enter the IP into the URL bar of your web browser.

3.Wi-Fi access:

- SSID: allegro-mm-xxxx (individual per device)

- WPA2 password: Allegro-MM

- Enter https://allegro/ or https://192.168.4.1/ into the URL bar of a browser.

4.Web interface authentication:

- User name: admin

- Password: allegro

4. Management Interface Conguration

You can congure the management interfaces by accessing the web interface at ‘Settings‘

 ‘Management interface settings’. The available options are described in the online manual

which can be accessed via the web interface.

Default conguration is bridge mode, thus running as an inline device. The link mode can be

congured via a web interface (menu ‘Settings‘  ‘Global settings’):

Power supply MGMT LANMGMT WLAN

Installation Guide

Allegro Network Multimeter 1500, 3500 and 5500

Default Settings

LAN: DHCP client

Wi-Fi SSID: allegro-mm-(see top label)

Wi-Fi URL: https://allegro/ or

https://192.168.4.1

Wi-Fi WPA2 key: Allegro-MM

Web interface user name: admin

Web interface password: allegro

Overview

1. Package Contents

2. Hardware Deployment

3. Device Start

4. Management Interface Conguration

5. Conguration Reset

6. Firmware Update Notication

7. Factory Reset

8. Manual

1. Package Contents

1 x Allegro Network Multimeter 1500, 3500 or

5500 incl. redundant power supply unit

2x Power cable

1 x Rack rail set

1 x Wi-Fi USB adapter (already pre-installed)

The Allegro Network Multimeter package contains the following items:

1 x Screw set for HDDs

1 x Screw set for rack rail set

36 x 3.5“ HDD mounting frame

1 x Installation guide

The guide contains the following sections:

If you have any questions regarding the Allegro Network Multimeter, please feel free to contact us: allegro-packet.com/support.

6. Firmware Update Noti ication

Update information via email

With each release, Allegro Packets will send you an email with release notes and a link to

download the update. If you want to be added to this mailing list, please contact us:

allegro-packets.com/support.

Using the Allegro web interface

Start your Allegro Network Multimeter and click ‘Settings’ on the left side of the menu and then

‘Firmware updates’. Click on ‘Check for new firmware’ and the Allegro Network Multimeter will

tell you if a new version is available for download. If so, you can choose to download it directly to

the device. In addition, this page provides an overview of all versions available to you. To start

the new version, click on ‘Activate’.

7. Factory Reset

The ‘Factory reset‘ will clear the entire system installation and restore the firmware to the ver-

sion that was originally shipped with the Allegro Network Multimeter.

1. Power o the Allegro 1500, 3500 or 5500.

2. Remove all network cables from the device.

3. Connect a display to the VGA port.

4.Connect a USB keyboard to any of the four USB ports.

5. Power on the device by pressing the power button.

6.After initialization a boot menu appears. Select ‘Factory reset’ and press Enter. Or select

‘Conguration reset’ to reset the conguration settings only while keeping the current rm-

ware installation.

7. The device will boot, reset everything to factory settings, and reboot again.

8.The device is now reset to factory settings.

9. Disconnect the display and keyboard.

8. Manual

The device manual can be accessed from the web interface. Each web section contains a button

to access context-specic documentation, the complete manual can be opened by clicking on

the ‘Manual’ link in the menu.

Getting Help:

5. Conguration Reset

The ‘Conguration reset‘ restores the conguration to the default settings:

1. Web interface: Go to menu ‘Settings‘  ‘Administration’ and click on ‘Reset system congu-

ration’. All settings including the network conguration will be reset to factory default.

2.Boot menu: Follow the instruction in the section 7. Factory Reset.

Questo manuale è adatto per i seguenti modelli

Altri manuali Allegro Packets Hardware di rete

Allegro Packets

Allegro Packets 1510 Manuale utente

Allegro Packets

Allegro Packets 1310 Manuale utente

Allegro Packets

Allegro Packets 1410 Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente