allen HP105 Guida all'applicazione
OPERATIONS - PARTS
MANUAL
Riding Trowel
This manual, or a copy of it, must be kept with the machine at all times.
There is a manual storage container located on the machine for your convenience.
HP105 Riding Trowel
OPERATIONS - PARTS MANUAL
This manual covers the products listed below:
Copyright © 2015 Allen Engineering Corporation
All rights reserved
All information, specications, and illustrations in this manual are subject to change without notice and
are based on the latest information at the time of publication. No part of this manual may be reproduced
or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the
express written permission of Allen Engineering Corporation (AEC). AEC assumes no responsibility or
liability for any errors or inaccuracies that may appear in this manual.
Allen Products are covered under one or more of the following patent numbers:
U.S. Design Patents: 344,736; 400,542; 400,544; 402,998; 402,999; 403,332; 404,041; 404,042;
410,931; 413,127; 416,564; 465,897; 466,909; 474,203.
U.S. Utility Patents: 5,108,220; 5,238,323; 5,328,295; 5,352,063; 5,405,216; 5,476,342; 5,480,257;
5,480,258; 5,533,831; 5,562,361; 5,567,075; 5,613,801; 5,658,089; 5,685,667; 5,803,658; 5,816,739;
5,816,740; 5,890,833; 5,934,823; 5,967,696; 5,988,938; 5,988,939; 6,019,433; 6,019,545; 6,048,130;
6,053,660; 6,089,786; 6,106,193; 6,857,815; 5,288,166; 6,582,153 B1, 7,108,449; 7,114,876;
7,316,523; 7,690,864 B2
Canadian Patents: 2,039,893.
First Issue: July 2015
Amended: February 2018
Printed in U.S.A.
Part No. Description
064200 TWIN ENGINE RIDER, HP105
064355 - 06/2015
Page 4
LIMITED WARRANTY and LIMITATION OF LIABILITY
Allen Engineering Corporation (“Allen”) warrants its products to be free of defects in material or workmanship for the following
periods:
A. New Machines and Parts.............................................................................One Year
Warranty period begins on rst day of use by End User. This rst day of use is established by the date of a completed Allen
Warranty Card or a Bill of Sale to the End User. All warranty is based on the following limited warranty terms and conditions,
including the disclaimer of implied warranties and consequential damages.
1. Allen’s obligation and liability under this warranty is limited to repairing or replacing parts if, after Allen’s inspection, there is
determined to be a defect in material or workmanship. Allen reserves the choice to repair or replace.
2. If Allen chooses to replace the part, it will be at no cost to the customer and will be made available to the Allen Distributor,
Dealer, or Rental Center from whom the End User purchased the product.
3. Replacement or repair parts, installed in the product, are warranted only for the remainder of warranty period of the product
as though they were the original parts.
4. Allen does not warranty engines. Engine warranty claims should be made directly to an authorized factory service center
for the particular engine manufacturer.
5. Allen’s warranty does not cover the normal maintenance of products or its components (such as engine tune-ups and oil &
lter changes). The warranty also does not cover normal wear and tear items (such as belts and consumables).
6. Allen’s warranty will be void if it is determined that the defect resulted from operator abuse, failure to perform normal main-
tenance on the product, modication to product, alterations or repairs made to the product without the written approval of
Allen. Allen specically excludes from warranty any damage to any trowels resulting from an impact to the rotors.
7. Impact damage is not covered under the Allen Gear Box warranty.
8. Allen will pay shop labor on warranty items at the Allen Shop Labor Rate in existence on the date of the warranty claim.
An Allen Labor Chart will determine the time allowed to complete a repair and will govern the shop labor hours that will be
allowed.
9. Allen will pay freight on warranty replacement parts at worldwide standard ground rates. No warranty replacement parts
will be shipped air freight at the expense of Allen. Allen only pays outbound freight charges when sending warranty replace-
ment parts to the customer via ground service. Allen does not pay any inbound freight. However, if Allen determines this to be
a warranted item, only then will Allen reimburse the customer for inbound freight at standard ground rates.
10. ALLEN ENGINEERING CORPORATION’S WARRANTY POLICY WILL NOT COVER THE FOLLOWING: TAXES;
SHOP SUPPLIES; ENVIRONMENTAL SURCHARGES; AIR FREIGHT; TRAVEL TIME; LOSS OF TIME; INCONVENIENCE;
LOSS OF RENTAL REVENUE; RENTAL COSTS OF EQUIPMENT USED TO REPLACE THE PRODUCT BEING REPAIRED;
LOSS OF USE OF THE PRODUCT; COMMERCIAL LOSS; OR ANY OTHER CHARGES WHATSOEVER OR ANY LIABILI-
TIES FOR DIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE OR DELAY.
11. ALLEN ENGINEERING CORPORATION MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED. THIS LIMITED
WARRANTY IS IN LIEU OF THE WARRANTY OF MERCHANTABILITY AND FITNESS. THERE ARE NO OTHER
WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THIS DOCUMENT.
12. No Allen employee or representative is authorized to change this warranty in any way or grant any other warranty unless
such change is made in writing and signed by an ofcer of Allen Engineering Corporation.
Limited Warranty
064355 - 06/2015 Page 5
Table of Contents
Title Page
Limited Warranty 4
Table of Contents 5
Information Contained In This Manual 7
Dealer Information 8
Ordering Parts 9
Model Number - Serial Number Codes 10
Unit Identication 11
Technical specications 12
Engine Specications 13
Machine Dimensional Specications 14
CE Declaration of Conformity 15
Section 1 - Safety
State Regulations 16
Federal Regulations 17
Safety Information 18
Safety Symbols 19
General Safety 20
Safety Labels and Decals 25
Lifting Safety 29
Transportation Safety 30
Section 2 - Operations
Pre-Operating Instructions 31
Operating 32
Section 3 - Service
Maintenance Instructions 36
Air Filter Maintenance 37
Engine Oil Maintenance 38
Maintenance Schedule 39
Filter Replacement 40
Troubleshooting 41
064355 - 06/2015
Page 6
Table of Contents - Continued
Title Page
Section 4 - Parts
Factory Service Information 42
Replacement Part Procedure 43
Seat Frame Assembly 44
Right Rotor Module Assembly 48
Right Rotor Assembly 52
Left Rotor Module Assembly 54
Left Rotor Assembly 58
Right Spider Assembly 60
Left Spider Assembly 61
Fuel System Assembly 62
Spray System Assembly 64
Steering System Assembly 68
LH Gearbox Assembly 70
RH Gearbox Assembly 72
Throttle Pedal Assembly 74
Kill Switch Pedal Assembly 76
Throttle System Assembly 78
Pitch Control Assembly 80
Mainframe Assembly 82
Electrical Schematics 86
Section 5 - Accessories
Front Dolly Jack Assembly 92
Rear Dolly Jack Assembly 94
Trowel Arm Alignment Jig Assembly 96
Accessories 98
064355 - 06/2015 Page 7
Information Contained in this
Manual
This manual provides information and procedures to safely operate and maintain the Allen Machine.
For your own safety and protection from personal injury, carefully read, understand, and observe the
safety instructions described in this manual. Keep this manual or a copy of it with the machine at all
times.
Always operate this machine in accordance with the instructions described in this manual. A well main-
tained piece of equipment will provide many years of trouble free operation.
This manual is divided into the following sections:
SECTION 1
SAFETY
SECTION 3
SERVICE
SECTION 2
OPERATIONS
SECTION 4
PARTS
Complete any warranty requirements as specied by the engine manufacturer in their instructions
found inside the manual box located on the operator’s control panel.
Your engine is not manufactured by Allen Engineering Corporation, Inc, and therefore is not covered
under Allen Engineering Corporation, Inc warranty.
Your engine manufacturer should be contacted if you wish to purchase a parts manual or a repair man-
ual for your engine.
Refer to enclosed owners engine manual for complete O&M instructions. See your battery manufactur-
er for battery warranty.
SECTION 5
ACCESSORIES
064355 - 06/2015
Page 8
Dealer Name: _____________________________________________________________
Phone #: (____) - ____ - ____________________________________________________
Address: ________________________________________________________________
City:__________________________________State:________ Zip:___________________
Salesman: _______________________________Mobile Phone _____________________
Additional Comments: ______________________________________________________
________________________________________________________________________
________________________________________________________________________
Your Dealer has Allen Engineering Corporation trained mechanics and original Allen replacement parts.
Always contact the Allen Dealer who sold you this machine for Allen Certied repairs and replacement
parts.
Place Allen Dealer information below for future reference.
Dealer Information
064355 - 06/2015 Page 9
Ordering Parts
Section 4 contains illustrated parts lists for help in ordering replacement parts for your machine. Fol-
low the instructions below when ordering parts to insure prompt and accurate delivery:
1. All orders for service parts - include the serial number for the machine. Shipment
will be delayed if this information is not available.
2. Include correct description and part number from the “PARTS” section of this
manual.
3. Specify exact shipping instructions, including the preferred routing and complete
destination address.
4. DO NOT return parts to AEC without receiving written authorization from AEC. All
authorized returns must be shipped pre-paid.
5. When placing an order, please contact the AEC dealer nearest you.
All information, specications, and illustrations in this manual
are subject to change without notice and are based
on the latest information at the time of publication.
VISIT US!!! www.alleneng.com
LIKE US!!! www.facebook.com/AllenEngineering
FOLLOW US!!! @alleneng
WATCH US!!! www.youtube.com/AllenMachinery
064355 - 06/2015
Page 10
Model Number - Serial Number Codes
Manufacturer’s Codes:
When ordering parts or requesting service information, you will always be asked to specify the model
and serial numbers of the machine. The legends below specically denes each signicant character
or group of characters of the Model Number and Serial Number codes.
Model Number
HP 105
Series
105
High Performance
Serial Number
The serial number found on the identication plate is a ten digit format. The model number identies
your machine and will ensure that you receive the correct replacement parts.
Serial Number Example
105 04 15 001
Series
105
Month
Year
Sequence Number
Indice
Altri manuali allen Cazzuola
allen
allen HDX Series Guida all'applicazione
allen
allen HP205 Guida all'applicazione
allen
allen PRO 430 Guida all'applicazione
allen
allen MP245 Guida all'applicazione
allen
allen MSP475 Guida
allen
allen PRO WALK-BEHIND Guida all'applicazione
allen
allen MSP445 Guida all'applicazione
allen
allen Hydra-Drive Extreme Series Guida
allen
allen MSP475 Manuale utente
allen
allen HDX750 Guida all'applicazione
Manuali Cazzuola popolari di altre marche
Wacker Neuson
Wacker Neuson CT 36-400E Manuale utente
MULTIQUIP
MULTIQUIP BH11C Manuale del proprietario
Atlas Copco
Atlas Copco BG 240 E Guida alla manutenzione e all'assistenza
MULTIQUIP
MULTIQUIP Whiteman STXD6i Manuale utente
MQ Multiquip
MQ Multiquip JS36/30H55DE Series Guida
swepac
swepac TR 600P Manuale utente
