Alliance Laundry Systems 802715 Manuale utente

Para bajar una copia de estas instrucciones en español, visite www.comlaundry.com.

Keep these instructions for future reference.

(If this machine changes ownership, this manual must accompany machine.)

www.comlaundry.com

Installation Instructions

for Stacked Washers and Dryers

Dimensions........................................................................ 2

Before You Start................................................................ 4

Installation......................................................................... 5

Installer Checklist ........................................................... Back Cover

Date Purchased ________________

Model Number ________________

Serial Number _________________

Part No. 802715

December 2006

Inside.....................................

The following information applies to the state of Massachusetts, USA.

•This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.

•This appliance must be installed with a 36 inch (91 cm) long flexible gas connector.

•A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance.

•This appliance must not be installed in a bedroom or bathroom.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

• WHAT TO DO IF YOU SMELL GAS:

– Do not try to light any appliance.

– Do not touch any electrical switch; do not use any phone in your building.

– Clear the room, building or area of all occupants.

– Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

– If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

W052

FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of

fire or explosion or to prevent property damage, personal injury or death.

W033

WARNING

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

W053

WARNING

means without the expressed written consent of the publisher.

802715

Dimensions

SWD829N

* With leveling legs turned into base.

SWD829N

23.5 in.

(59.7 cm)

28 in.

(71.1 cm)

*75 in. (190.5 cm)

26.9 in.

(68.3 cm)

8.0 in.

(20.3 cm) 15.4 in.

(39.1 cm)

5.25 in.

(13.3 cm)

*44.1 in. (112 cm)

2.0 in.

(5.1 cm)

*29.6 in. (75.1 cm)

*31.1 in. (79 cm)

24 in.

(61 cm)

*13.1 in.

(33.3 cm)

ELECTRIC DRYERS

*14.6 in.

(37.08 cm)

*37.44 in. (95.1 cm)

SWD830N

*With leveling legs turned into base.

13/8 in. NPT Gas Connection

SWD830N

23.5 in.

(59.7 cm)

28 in.

(71.1 cm)

8.0 in.

(20.3 cm)

*75 in. (190.5 cm)

2.3 in.

(39.1

cm)

15.4 in.

(39.1 cm)

26.9 in.

(68.3 cm)

5.25 in.

(13.3 cm)

*44.1 in. (112 cm)

*29.6 in. (75.1 cm)

*31.1 in. (79 cm)

*42.4 in. (107.7 cm)

2.0 in.

(5.1 cm)

24 in.

(61 cm)

*13.1 in.

(33.3 cm)

GAS DRYERS

*14.6 in.

(37.08 cm)

*37.44 in. (95.1 cm)

Before You Start

Supplies

For most installations, the basic supplies you will need

are:

Figure 1

NOTE: If the the unit is delivered on a cold day

(below freezing), or is stored in an unheated room

or area during the cold months, do not attempt to

operate it until the unit has had a chance to warm

up.

NOTE: Some moisture in the wash drum is normal.

Water is used during testing at the manufacturer.

DRY2023N

1Safety Glasses

2Wood Block

3Power Cord (Electric Models)

4Wrench

5Screwdriver

6Level

75/16 Inch Socket Wrench

8Duct Tape

9Teflon Tape (Gas Models)

123

Any disassembly requiring the use of

tools must be performed by a suitably

qualified service person.

W299

WARNING

802715

Installation

Step 1: Position Unit Near Installation

Area

Move unit as close to the desired area of installation as

possible.

NOTE: For best performance and to minimize

vibration or movement, install washer on a solid,

sturdy and level floor. Some floors may need to be

reinforced, especially on a second floor or over a

basement. Do not install the washer on carpeting,

soft tile, a platform or other weakly supported

structures.

Step 2: Connect Fill Hoses

Water Supply

Water supply faucets must fit standard 3/4 inch

(19.1 mm) female garden hose couplings. DO NOT

USE SLIP-ON OR CLAMP-ON CONNECTIONS.

Water supply faucets should be readily accessible to

permit turning them off when washer is not being

used.

Recommended cold water temperature is 60o to

80oFahrenheit (16oto 27oCelsius). Recommended

hot water temperature is 120oto 140oFahrenheit

(49oto 60oCelsius). Warm water is a mixture of hot

and cold water. Warm water temperature is dependent

upon water temperature and pressure of both the hot

and cold water supply lines.

Water pressure must be a minimum of 20 to a

maximum of 120 pounds per square inch (138 to

827 kPa) static pressure measured at the faucet.

NOTE: Water pressure under 20 pounds per

square inch (138 kPa) will cause an extended fill

time in the washer and may not properly flush out

the detergent dispenser.

Turn on the water faucets and flush the lines for

approximately two minutes to remove any foreign

material that could clog the screens in the water

mixing valve.

NOTE: When installing in newly constructed or

renovated buildings, it is very important to flush

the lines since build-up may have occurred during

construction.

Washer and dryer are not designed to be

operated as separated, side-by-side units.

W187

WARNING

Under certain conditions, hydrogen gas

may be produced in a hot water system

that has not been used for two weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If

the hot water system has not been used

for such a period and before using the

washer, turn on all hot water faucets and

let the water flow from each for several

minutes. This will release any

accumulated hydrogen gas. The gas is

flammable. Do not smoke or use an open

flame during this time.

W029

WARNING

Connecting Hoses

Remove the two plain rubber washers and two filter

screens from the accessories bag. Install them into

each end of the fill hoses as shown in Figure 2. The

screen must be facing outward.

Screw hose couplings with the filter screens onto the

water faucets until they are finger-tight. Then, using a

pliers, screw approximately 1/4 turn.

Screw hose couplings from other end of hoses onto the

water mixing valve until they are finger-tight. Then,

using a pliers, screw approximately 1/4 turn. Refer to

Figure 3.

IMPORTANT: Do not cross thread or overtighten

couplings. This will cause them to leak.

Turn water on and check for leaks. If leaks are found,

turn off the water, unscrew hoses and reinstall them

until there are no leaks.

IMPORTANT: Turn off water supply whenever

there will be an extended period of non-use.

IMPORTANT: Hoses and other natural rubber

parts deteriorate after extended use. Hoses may

develop cracks, blisters or material wear from the

temperature and constant high pressure they are

subject to.

All hoses should be checked on a yearly basis for

any visible signs of deterioration. Any hose showing

the signs of deterioration listed above should be

replaced immediately. All hoses should be replaced

every five years.

IMPORTANT: Turn off water supply faucets after

check-out and demonstration. Owner should turn

off water supply whenever there will be an

extended period of non-use.

NOTE: Longer fill hoses are available (as optional

equipment at extra cost) if the hoses supplied with

the washer are not long enough for the installation.

Order hoses as follows:

No. 20617 Fill Hose (8 feet) (2.44 m)

No. 20618 Fill Hose (10 feet) (3.05 m)

TLW1976N

1 Water Faucet

2Fill Hose

3Plain Rubber Washer

4Hose Coupling

5Filter Screens

Figure 2

HOT

COLD

SWD596N

1 Water Faucets

2Cold Water Connection

3Hot Water Connection

4Water Fill Hoses

Figure 3

SWD596N

WATER

MIXING VALVE

802715

Risers

Risers (or air cushions) may have to be installed if the

pipes knock or pound when flow of water stops. The

risers are more efficient when installed as close as

possible to the water supply faucets (refer to Figure 4).

Step 3: Connect Drain Hose to Drain

Receptacle

Remove the drain hose from its shipping position on

the rear of the washer by unhooking the hose from the

retainer clamp and by removing the shipping tape.

Install the drain hose into the drain receptacle

(standpipe, wall or laundry tub) following the

instructions below.

IMPORTANT: Drain receptacle must be capable of

handling a minimum of 1-1/4 inch (32 cm) outside

diameter drain hose.

Standpipe Installation:

Place the drain hose into the standpipe.

Remove the beaded strap from accessories bag and

place around standpipe and drain hose and tighten

strap to hold hose to standpipe. Refer to Figure 5. This

will prevent the drain hose from dislodging from drain

receptacle during use.

W005I

1 Water Supply Faucets

2Risers (Air Cushions)

Figure 4

W005I

SWD598N

1 Drain Hose

2Beaded Tie-Down Strap

3Standpipe 2 in. (5.08 cm) or 1-1/2 in. (4 cm)

Figure 5

SWD598N

24 in. to 36 in.

(61 to 91.44 cm)

Recommended

Height

Wall Installation:

For installations of this type, the drain hose MUST be

secured to one of the fill hoses using the beaded strap

from accessories bag. Refer to Figure 6.

NOTE: End of drain hose must be below 24 in.

(61 cm).

Laundry Tub Installation:

For this type of installation, the drain hose MUST be

secured to the stationary tub to prevent hose from

dislodging during use. Refer to Figure 7. Use the

beaded strap (supplied in accessories bag) to secure

hose.

H023I

1 Drain Hose

2Beaded Strap (tape if necessary)

3Fill Hoses

Figure 6

SWD600N

1 Drain Hose

2Tie-Down Strap (tape if necessary)

Figure 7

SWD600N

802715

Step 4: (Gas Dryer Only) Connect Gas

Supply Pipe

1. Make certain your dryer is equipped for use with

the type of gas in your laundry room. Dryer is

equipped at the factory for Natural Gas with a

3/8 inch NPT gas connection.

NOTE: The gas service to a gas dryer must

conform with the local codes and ordinances, or in

the absence of local codes and ordinances, with the

latest edition of the National Fuel Gas Code ANSI

Z223.1/NFPA 54 or the CAN/CGA-B149, National

Gas Installation Code.

Natural Gas, 1000 Btu/ft3(37.3 MJ/m3) service must

be supplied at 6.5 ± 1.5 inch water column pressure.

For proper operation at altitudes above 3000 feet

(915 m) the natural gas valve spud orifice size must be

reduced to ensure complete combustion. Refer to

Table 1.

2. Remove the shipping cap from the gas

connection at the rear of the dryer. Make sure you

do not damage the pipe threads when removing

the cap.

3. Connect to gas supply pipe.

NOTE: When connecting to a gas line, an

equipment shut-off valve must be installed within

6 feet (1.8 m) of the dryer. An 1/8 in. NPT pipe plug

must be installed as shown for checking inlet

pressure. Refer to Figure 8.

4. Tighten all connections securely. Turn on gas and

check all pipe connections (internal & external)

for gas leaks with a non-corrosive leak detection

fluid.

To reduce the risk of gas leaks, fire or

explosion:

• The dryer must be connected to the type

of gas as shown on nameplate located in

the door recess.

• Use a new flexible stainless steel

connector.

• Use pipe joint compound insoluble in L.P.

(Liquified Petroleum) Gas, or Teflon tape,

on all pipe threads.

• Purge air and sediment from gas supply

line before connecting it to the dryer.

Before tightening the connection, purge

remaining air from gas line to dryer until

odor of gas is detected. This step is

required to prevent gas valve

contamination.

• Do not use an open flame to check for gas

leaks. Use a non-corrosive leak detection

fluid.

• Any disassembly requiring the use of

tools must be performed by a suitably

qualified service person.

W316

WARNING

Natural Gas Altitude Adjustments

Altitude Orifice Size Part No.

feet m No. inches mm

3000 915 43 0.0890 2.26 503778

6000 1830 44 0.0860 2.18 58719

8000 2440 45 0.0820 2.08 503779

9000 2740 46 0.0810 2.06 503780

10,000 3050 47 0.0785 1.99 503781

Ta bl e 1

D434I

1New stainless steel flexible connector -

(Use design CSA certified connector)

Use only if allowed by local codes

21/8 in. NPT Pipe Plug

3Equipment Shut-Off Valve

4Black Iron Pipe Shorter than 20 ft. (6.1 m) -

Use 3/8 in. (9.5 mm) pipe

53/8 in. NPT Gas Connection

Figure 8

NOTE: The dryer and its appliance main gas valve

must be disconnected from the gas supply piping

system during any pressure testing of that system

at test pressures in excess of 1/2 psi (3.45 kPa).

Refer to Step 12 (Check Heat Source).

L.P. (Liquefied Petroleum) Gas, 2500 Btu/ft3

(93.1 MJ/m3) service must be supplied at 10 ± 1.5 inch

water column pressure.

For proper operation at altitudes above 3000 feet

(915 m) the L.P. gas valve spud orifice size must be

reduced to ensure complete combustion. Refer to

Table 2.

NOTE: DO NOT connect the dryer to L.P. Gas

Service without converting the gas valve. Install

L.P. Gas Conversion Kit 649P3, available at extra

cost.

Step 5: (Electric Dryer Only) Connect

Electrical Plug

Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz,

3 or 4 wire electrical suppy. Refer to serial plate for

specific electrical requirements.

NOTE: The wiring diagram is located behind the

control panel, inside the control cabinet.

Grounding Information

•This dryer must be connected to a grounded

metal, permanent wiring system; or an

equipment-grounding conductor must be run

with the circuit conductors and connected to the

equipment-grounding terminal or lead on the

dryer.

•The dryer has its own terminal block that must be

connected to a separate branch, 60 Hertz, single

phase circuit, AC (alternating current) circuit,

fused at 30 Amperes (the circuit must be fused

on both sides of the line). Electrical service for

the dryer should be of maximum rated voltage

listed on the nameplate. Do not connect dryer

to 110, 115, or 120 volt circuit.

•Heating elements are available for field

installation in dryers which are to be connected to

electrical service of different voltage than that

listed on nameplate, such as 208 Volt.

•If branch circuit to dryer is 15 feet (4.57 m) or

less in length, No. 10 AWG wire (copper wire

only), or as required by local codes. If over

15 feet (4.57 m), use No. 8 AWG wire (copper

wire only), or as required by local codes. Allow

sufficient slack in wiring so dryer can be moved

from its normal location when necessary.

•The power cord connection between wall

receptacle and dryer terminal block IS NOT

supplied with dryer. Type of power cord and

gauge of wire must conform to local codes.

L.P. Altitude Adjustments

Altitude Orifice Size Part No.

feet m No. inches mm

3000 915 55 0.0520 1.32 58755

8000 2440 56 0.0465 1.18 503786

Ta bl e 2

To reduce the risk of fire, electric shock,

serious injury or death, all wiring and

grounding MUST conform with the latest

edition of the National Electrical Code,

ANSI/NFPA 70, or the Canadian Electrical

Code, CSA C22.1, and such local

regulations as might apply. It is the

customer’s responsibility to have the wiring

and fuses installed by a qualified electrician

to make sure adequate electrical power is

available to the dryer.

W521

WARNING

Indice

Altri manuali Alliance Laundry Systems Rondella

Alliance Laundry Systems

Alliance Laundry Systems SF7000WE Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems StGeorge Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems W446I Guida

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen LFNE5B Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems Frontload Washer Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems Cygnus Premium Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems HC20BC2 Manuale

Alliance Laundry Systems

Alliance Laundry Systems HWFB61WN1102 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems LWS02M series Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems PHM1401C Manuale del proprietario

Alliance Laundry Systems

Alliance Laundry Systems HF455 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems AWN43RSN115CW01 Istruzioni operative

Alliance Laundry Systems

Alliance Laundry Systems 800138R2 Manuale del proprietario

Alliance Laundry Systems

Alliance Laundry Systems HF18VCV Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems POCKET HARDMOUNT UW50P4 Guida alla manutenzione e all'assistenza

Alliance Laundry Systems

Alliance Laundry Systems UW35PV Series Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems 802749r1 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems WF150 Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems HA1000 Istruzioni per il montaggio

Alliance Laundry Systems

Alliance Laundry Systems H370I Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems LWS16A series Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems HCL020HDF Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems Frontload Washer Manuale utente

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen TV2000WN Manuale utente

Manuali Rondella popolari di altre marche

Tricity Bendix

Tricity Bendix AW 1000 W Guida del prodotto

Panasonic

Panasonic NA-F60L5WRB Manuale utente

GE WSLP1500 Manuale

Electrolux

Electrolux EWF1284EDW Manuale utente

Bosch

Bosch WAN2829BSN Manuale utente

LG TV2516DV3B Manuale utente

LG TH2517DSAV Manuale utente

VESTEL

VESTEL CMH-XL 7510 TE Manuale utente

AEG

AEG 74335 Manuale operativo

Johnson

Johnson JWF721A Manuale utente

Beko

Beko WTE7604XLW0 Manuale utente

Danby

Danby DTT100A1WDB Istruzioni per il montaggio

Amica

Amica WA 14 Ex Manuale utente

Daewoo

Daewoo DWD-F1222 Manuale utente

Bosch

Bosch WAS28461AU Manuale utente

Miele

Miele PW 6080 Vario Manuale utente

Finlux

Finlux FLX108CF220 Manuale utente

Whirlpool

Whirlpool 3LBR5132AN0 Manuale utente