ALM Tyso Daiko Manuale utente
ALM-031 - ‘Tyso Daiko’
Manual Version: 0.1
ALM031
TYSO!
DAIKO
USER
GUIDE.
of1 12
ALM-031 - ‘Tyso Daiko’
Introduction 3.......................................................................................
Features 3--------------------------------------------------------------------
Technical Specifications 4----------------------------------------------------
Operation 4...........................................................................................
Panel Layout 4----------------------------------------------------------------
General Usage 5---------------------------------------------------------------
Patch Ideas 7........................................................................................
Dual Drum Voices (Kick + Snare) 7---------------------------------------------
Stacking Voices 8-------------------------------------------------------------
Limited Warranty 9................................................................................
Support 10............................................................................................
APPENDIX 11...........................................................................................
I. Calibration 11----------------------------------------------------------------
II. Firmware Updates 11--------------------------------------------------------
of2 12
ALM-031 - ‘Tyso Daiko’
Introduction
The ‘Tyso Daiko’ is a dual 12-bit digital wavetable drum voice with full voltage
control and an analog EQ output path.
The twin voices are independently triggered and output, but share pitch,
envelope and other parameters of a swept wavetable oscillator. One voice is output
through a voltage controlled analog tilt EQ emphasising upper or lower frequencies.
The other voice is output through a digital wavefolder which adds increasing
timbral complexity (to noise).
Both voices respond independently to an accent input and the first voice is able
to be 'choked' . A surface control allows for fine control of additional transients
from a click to a slow attack. Full voltage control including a V/Oct pitch input
makes the Daiko an expressive and wide ranging drum module with extremely wide
pallet of sounds with lots of modulation possibilities.
Features
•Twin wavetable drum voices run through an analog tilt EQ and a digital
wavefolder respectively.
•Frequency swept oscillator with 1V/Oct tracking, morphing wavetables (11
waves) and self FM capability
•Attack and Release envelopes.
•Dual trigger, accent and choke inputs.
•Surface control for additional ‘punch’ or reduced attack.
•External mix input through tilt the EQ.
•Full voltage control of all params.
•Skiff friendly with reverse power protection.
•Made in England!
of3 12
ALM-031 - ‘Tyso Daiko’
Technical Specifications
•Supply: +12V 70mA Max / -12v 35mA
•Size: 14 HP
•Depth: 32mm
Operation
Panel Layout
of4 12
V/Oct
Start
Choke
Trig 1 Trig 2
Acc
Rate Release
Wave Surface
End
Fold 2
-TYSO-DAIKO-
EQ
Outs
1. 2.
Ext in EQ
→1.
PITCH
↗
→
Pitch Sweep
Section
Trigger, Accent and
Choke inputs
Waveform selection
and release controls
Main CV Inputs
(All approx -5-5v)
Surface control
(Add clicks/attack)
Wave folder Control
(Voice 2 only)
Tilt Filter EQ control
section
(Voice 1 only)
Voice 1 & 2 Outputs
ALM-031 - ‘Tyso Daiko’
General Usage
‘Tyso Daiko’ produces a drum ‘hit’ sound when a trigger signal (approx. +3v rising
edge) is applied to either trigger input. Trig 1 is normalised to Trig 2 meaning it will
trigger both voices when Trig 2 is unpatched. The two other trigger inputs - Acc
(Accent) and Choke - respectively either further (de)emphasise the hit sound or
immediately stop it in the presence of a trigger signal.
The actual ‘hit’ sound is defined by the control knob positions and associated
control voltage input levels. All control knobs are offsets - any incoming control
voltage is added to them. They do not attenuate incoming control signals. Control
inputs are all approx -5v to +5v.
Each voice’s sound is produced by a ‘ramped’ wavetable oscillator changing
pitch between the defined start and end frequencies at a rate set by the rate
control. The surface control optionally then adds a ‘click’ or attack envelope to the
sound and the release controls the sounds release envelope. All these parameters
are shared between both voices but voice one is passed through an analog EQ
whilst voice 2 is passed through a wave folder - each of these sections have their
own controls and inputs also.
Pitch Section Controls
A ‘ramped’ oscillator provides waveforms for both voices sweeping between
start and end pitches at a defined rate and offset via a base pitch.
The ‘Rate’ control sets the rate of travel between the start and end pitches,
looping back around once a sweep is completed. Pitch sweep is disabled with the
Rate control fully counter clock wise (CCW).
The Start control sets the start frequency of the sweep or a fixed offset if pitch
sweep is disabled (rate full CCW).
The End control sets the end frequency of the pitch sweep. It is inactive when
the sweep is disabled.
The V/Oct input adds a base pitch offset to both the start and end frequencies. It
tracks approx 5 octaves.
of5 12
ALM-031 - ‘Tyso Daiko’
Wave Control
Selects the source wave for both voices. Morphs between 11 different
waveforms which are:
noise > sine > tri > saw > pulse > voice > bell1 > bell2 > cymbal > spectra > buzz.
Release Control
The release time of the exponential volume envelope applied to both voices.
Ranges from approx 2ms - 14 seconds. Release time is doubled and halved by the
‘Accent’ input for Voice 1 and Voice 2 respectively.
Surface
Switches in a resonant click attack at the start of the sound, as the control is
turned up the click becomes sharper and quieter. After crossing the mid point, the
surface control becomes a slow volume attack envelope. Surface control has no
effect when set fully CCW.
Fold
Amount of wavefolding applied to the Voice 2 output. Ranges from no folding
(CCW), increasing brightness and harmonics into noise (CW).
EQ Control and input
An analog tilt style EQ filter emphasising either high (CCW) or low (CW)
frequencies on the Voice 1 output.
External Input - connect any audio signal to be mixed with Voice 1 pre EQ. For a
single dual voice output patch Out 2 back to the external input.
Accent & Choke Inputs
Accent - Alters the release time to approx. twice as long for Voice 1 and half as
long for Voice 2 with a high gate at the accent intput.
Choke - Stops audio immediately when a trigger is received. Only applies to
Voice 1. !
of6 12
ALM-031 - ‘Tyso Daiko’
Patch Ideas
Dual Drum Voices (Kick + Snare)
1. Patch a x1 clock from Pam (or other trigger sequencer) to the ‘Trig 1’ input.
Patch ‘out 1’ into a mixer and monitor the output.
2. Set ‘wave’ to a sine and ‘release’ to a shorter time.
3. Initiate a pitch sweep by turning up the ‘rate’ control. Set ’start’ to around 12
o’ clock and ‘end’ fully counter clockwise, then dial in the sweep time with ‘rate’.
Set the sweep time long enough that it does not loop over before the next hit.
4. Turn the EQ control clockwise until the low frequency is nicely emphasised.
5. To create a snare patch a half speed clock (i.e. /2 clock from Pam) to the Trig
2 input.
6. Patch ‘out 2’ to another channel of the mixer.
7. Turn the ‘fold’ control clockwise until the sound becomes more snare like
and noisy. Adjust release to taste.
Tips
1. Patching a high gate to ‘accent’ doubles the release time of voice 1 and
halves the release time of voice 2. Try using accent to further separate the
voices and make a more natural kick and snare.
2. For a harder hitting kick, try using the ‘surface’ control to dial in a sharper
transient click at the start of the hits.
of7 12
ALM-031 - ‘Tyso Daiko’
Stacking Voices
1. Patch a trigger sequence or clock to the ‘trig 1’ input, leave the ‘trig 2’ input
unpatched.
2. Monitor the audio from ‘out 1’.
3. Patch ‘out 2’ back to the ‘external in’ of the EQ section.
4. The voices now act as one, sharing the trigger input, tilt EQ, and audio
output.
5. Dial in a tonal sound to act as the ‘drum body’ and set ‘fold’ fully CW to act as
the noise element. Stacking voices works nicely for classic snare and tom like
sounds as well as other complex percussion.
Tips
1. Try slightly delaying a copy of the trigger source using a gate delay or
envelope’s ‘end of’ output. Patch the delayed copy to trigger voice 2 just after
voice 1 for clap like doubled sounds.
2. Patch ‘out 2’ through an attenuator prior to the ‘ext in’ for fine control over the
mix between voices.
of8 12
ALM-031 - ‘Tyso Daiko’
Limited Warranty
From the date of manufacture this device is guaranteed for a period of 2 years
against any manufacturing or material defects. Any such defects will be repaired or
replaced at the discretion of ALM. This does not apply to;
•Physical damage arising for mis treating (i,e dropping, submerging, etc).
•Damage caused by incorrect power connections.
•Overexposure to heat or direct sunlight.
•Damage caused by inappropriate or mis-use.
•Use of incorrect or non official firmware
No responsibility is implied or accepted for harm to person or apparatus caused
through operation of this product.
By using this product you agree to these terms. !
of9 12
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali ALM Sintetizzatore
