Alphatronics UNii Manuale utente

Alphatronics BV l Boekdrukker 5-7 l 3861 SE Nijkerk l Tel.: 033-2459944 l [email protected]

User manual

Handleiding voor de gebruiker

English page 4

Nederlands pagina 21

User manual UNii Rev.2.11 – 14-07-2022 2

Table of contents

INTRODUCTION...............................................................................................................................................................................4

Purpose of this manual _________________________________________________________________________________________4

General guidelines for use of the system ________________________________________________________________________4

Keypad...............................................................................................................................................................................................5

Keys____________________________________________________________________________________________________________5

Proximity sensor________________________________________________________________________________________________5

Display...............................................................................................................................................................................................6

Card reader.......................................................................................................................................................................................6

Sections and Groups......................................................................................................................................................................6

Operation ..........................................................................................................................................................................................7

Arming _________________________________________________________________________________________________________7

Disarming ______________________________________________________________________________________________________7

Hot keys ________________________________________________________________________________________________________7

Status __________________________________________________________________________________________________________7

Menu ___________________________________________________________________________________________________________8

Arming with a tag_______________________________________________________________________________________________8

Information_____________________________________________________________________________________________________8

Time switches __________________________________________________________________________________________________8

Test mode______________________________________________________________________________________________________8

Installer authorised _____________________________________________________________________________________________8

Audible signals of the system.......................................................................................................................................................8

User Menu ........................................................................................................................................................................................9

Information_____________________________________________________________________________________________________9

Notifications____________________________________________________________________________________________________9

Open inputs ____________________________________________________________________________________________________ 9

Section status __________________________________________________________________________________________________9

Event log _______________________________________________________________________________________________________9

System info_____________________________________________________________________________________________________9

UNii manager key_______________________________________________________________________________________________9

Overtime _______________________________________________________________________________________________________9

(Un)-Bypass ____________________________________________________________________________________________________9

Users__________________________________________________________________________________________________________10

Add user_______________________________________________________________________________________________________10

Edit existing user ______________________________________________________________________________________________10

Change name__________________________________________________________________________________________________10

Change code __________________________________________________________________________________________________10

Change code functionality _____________________________________________________________________________________10

User manual UNii Rev.2.11 – 14-07-2022 3

Change language ______________________________________________________________________________________________11

Change profile _________________________________________________________________________________________________11

Add tag________________________________________________________________________________________________________11

Remove tag ___________________________________________________________________________________________________11

Advanced settings ........................................................................................................................................................................11

Keypad settings _______________________________________________________________________________________________11

LED brightness ________________________________________________________________________________________________11

Display brightness _____________________________________________________________________________________________11

Key volume ____________________________________________________________________________________________________11

Buzzer volume_________________________________________________________________________________________________11

Proximity sensor_______________________________________________________________________________________________11

Doorbell _______________________________________________________________________________________________________11

mySmartControl _______________________________________________________________________________________________11

Change Date/Time_____________________________________________________________________________________________12

System test menu _____________________________________________________________________________________________12

Access installer________________________________________________________________________________________________12

Input test ______________________________________________________________________________________________________12

General ............................................................................................................................................................................................12

mySmartControl _______________________________________________________________________________________________12

Screensaver ___________________________________________________________________________________________________13

Alarm in a 24-hour zone _______________________________________________________________________________________13

Protection against the ‘unauthorised’ entering of PIN codes ____________________________________________________13

Menu overview ________________________________________________________________________________________________14

Definitions.......................................................................................................................................................................................15

European norms and security classes......................................................................................................................................15

APPENDIX A: DETECTOR DEPLOYMENT (can be filled in by the installer)........................................................................16

User manual UNii Rev.2.11 – 14-07-2022 4

INTRODUCTION

Purpose of this manual

The purpose of this manual is to help the user get familiar with the UNii intrusion system. The manual explains

about how to operate and control the control panel. Several of the special options explained in this manual can

only be executed by the main user (supervisor).

General guidelines for use of the system

Do not panic when the alarm goes off. Disarm the system with your PIN code, access tag or wireless remote

control (keyfob) and read the information that is shown on the display of the keypad.

The system works with a keypad that has an OLED display. The OLED displays information about the status of

your system. If the information on the display is not clear, first consult this user manual.

Never hand your PIN code, access tag or keyfob over to another user, this can lead to unpleasant situations.

If a malfunction occurs, first consult this user manual. If the fault persists, contact your installer immediately. Your

installer will give you further instructions.

Note important events (false alarm, user error, etc.) in a logbook including zone number, date, and time. During

annual maintenance, the installer may be able to take measures to prevent these situations in the future.

The UNii intrusion system is an advanced electronic device that has been professionally installed and

commissioned by a professional installer. This device is called the "control panel". The detection components,

optical and acoustic alarm devices such as strobe lights, sirens and alarm diallers are connected to the control

panel. The UNii is equipped with an integrated IP dialler that is connected to a free LAN port of your broadband

modem / router for reporting alarms to, for example, a monitoring station.

The UNii security alarm system is armed and disarmed via the connected keypad using a PIN code or access tag.

It is also possible to arm and disarm the security system via a (user) APP on the smartphone or tablet.

The system has been designed and tested according to the European standards regarding stability, reliability, and

insensitivity to external electrical interference.

User manual UNii Rev.2.11 – 14-07-2022 5

Keypad

Below is a picture of the UNii keypad.

Keys

The numerical keys 0 to 9 are used to enter a PIN code or numerical values in the menus.

The keypad has 4 black function keys, these keys are located above the numeric keys and have no fixed function.

Depending on the status of the system, the operation being performed or the menu in which the user is located,

the function of the function key may change. The function of the key is indicated by a text directly above the key in

the display. The 3 left function keys can also be used as a shortcut. A hotkey can perform a specific action, such

as switching on a certain section immediately in the night situation or activating an output. Ask your installer

about the options.

The keypad has Navigation keys, the numeric keys 2, 4, 6 and 8 are next to numeric keys also a navigation key.

When navigation is possible or desired, the key illumination will go out under all other keys. With the navigation

keys, only the keys of the navigation directions that are currently possible will light up.

Proximity sensor

The keypad is equipped with a proximity sensor. The proximity sensor causes the key backlight illumination and

OLED display to light up as soon as movement is detected in the nearby vicinity of the keypad. The sensitivity of

the proximity sensor can be set by the supervisor in the user menu. See keyboard settings later on in this manual.

1. OLED display

2. Keys

3. Function keys

4. Proximity sensor

5. Card reader (optional)

6. Navigation keys

User manual UNii Rev.2.11 – 14-07-2022 6

Display

In the picture below the OLED display of the UNii keypad is shown.

1. System name (2 lines)

2. Function of the function keys

3. Local Time

4. Indication that there is a message in the system.

5. Indication that the installer is authorised to enter the programming.

6. System is in test mode (contact your installer)

Card reader

The keypad of the UNii security system is available in 2 versions: a standard version and a luxury version with a

built-in card reader. The card reader is located directly under the numeric key 5. The card reader uses the latest

DESFire EV2 reading technology, the most secure reading technology at this moment. The reading distance of the

card reader is approximately 5 cm above the numeric key.

Sections and Groups

The UNii security system uses Sections and Groups.

A section is a part of the security system and can be armed and disarmed independently from the rest of the

system. An example of a section is for example, the ground floor of a residential house, a wing of an office

building or the warehouse of a company. Each section has a name that is programmed by the installer during

installation.

Groups can also be created above the section structure. A group can be created to arm or disarm multiple

sections simultaneously. An example of a group is complete floor of a building of the entire house, a group also

has a name that is programmed by the installer during installation.

Groups and sections can be armed and disarmed by a user by means of a PIN code or DESFire tag.

User manual UNii Rev.2.11 – 14-07-2022 7

Operation

Arming

To arm the system, press the function button "Arm", You will now be asked to enter a valid PIN code. Once the

valid PIN code has been entered, the section or group for which the user is authorized will be displayed and can be

armed. An open circle is shown in front of the name of the section or group, this indicates that the section or

group is disarmed, if the circle is flashing the section or group is not ready to be armed. If the circle is closed, then

the section or group is already armed.

Select the section or groups to be armed by using the "Select" function key, a tick () will appear behind each

section or group. Multiple section or groups can be selected. When all section or groups are selected press the

"Arm" function key to arm the selected sections or groups.

After starting the arming procedure, the exit delay is heard (if set) via the buzzer of the keypad. The buzzer beeps

faster during the last 5 seconds of the exit time. Opening a delayed zone after the exit time has expired will start

the entry procedure.

If an arming cannot be successfully completed (e.g., if an input remains open) then the system will not be armed.

At that moment, a double beep will be heard via the buzzer of the keypad and on the loudspeaker output of the

UNii.

In addition to using a PIN code, it is also possible to arm with a tag/card if the keypad is equipped with a built-in

card reader. For arming with a tag/card, see "Arming with a tag" later in this manual.

NB. When the system is configured by the installer for arming without a PIN-code, the step to request a PIN-code

will be skipped.

Disarming

To disarm the system, press the function button "Disarm", you will now be asked to enter a valid PIN code. After

entering a valid code, the sections or group that can be disarmed are displayed. A closed circle is displayed in

front of the name of the section or group, indicating that the section or group is armed. Use the "Select" function

key to select the section or group to be disabled, a tick () will appear after each section or group. Multiple

sections or groups can be selected. If all sections or groups are selected press the "Disarm" function key to

disarm the selected sections or groups.

Hot keys

The 3 left function keys can also be used as a hotkey. For example, your installer can program a hotkey to be used

to arm certain sections in the night mode or activate an output to open the gate. Ask your installer about the

options.

Status

The section statuses of the system can be viewed using the section function key. An open circle means section or

group disarmed, a flashing circle means section or group not ready to arm, and a closed circle means section or

group armed.

User manual UNii Rev.2.11 – 14-07-2022 8

This function key opens the user menu where several functions and menus can be found. See the “User

menu” chapter for more explanation about individual functions and menus.

Arming with a tag

If the keypad is equipped with a built-in card reader, it is possible to arm and disarm the system using a DESFire

EV2 tag or card. Depending on the tag settings (direct arm/disarm or normal), the tag will work as if a normal

(PIN) code has been entered and the user must first select the relevant sections or groups and press the "arm"

function key to arm. If direct is programmed the system will be armed immediately if all sections or groups linked

to the tag are disarmed. If one or more sections or groups are already armed, the system will disarm, arming will

be done by presenting the tag again.

Information

If information is present, the system will indicate this by showing the "i" symbol on the right-hand side of the

display and an audible beep via the buzzer of the keypad. With function key 3 (info) the information can be

displayed and possibly deleted. When all messages have been deleted, the "i" symbol will disappear from the

display.

Time switches

The system can be programmed to arm and disarm automatically, for an explanation see chapter "Time switch" in

the User menu.

Test mode

When the installer has placed the system in the test mode, the ‘!’ Symbol is shown in the display. For more

information consult your installer.

Installer authorised

If the installer is authorized by the supervisor (main user code) to access the system, a tool symbol is shown on

the right of the display. The supervisor has the choice to give the installer only installer rights or to give installer +

user rights. A time limit can also be entered for how long the installer has authorization for the system.

If the installer is not authorized by the supervisor, he cannot do anything in the system.

Audible signals of the system

Alarm: Alarm siren sound will be heard via the connected siren or speaker.

Fire: Slow-whoop fire sound will be heard via the connected siren or speaker.

Key stroke: Short tone 0,5 seconds.

Trouble buzzer: ●□●□● short tone every 10 seconds

(can de set to no sound during the night).

Entry buzzer: Constant tone (during programmed time).

Exit buzzer: □□□●□●□●□intermitted tone (last 5 seconds faster).

Tones ●= 0,5 sec. tone

= 1 sec. tone

□= pause

User manual UNii Rev.2.11 – 14-07-2022 9

User Menu

In this chapter the different programming options and functions of the (user) menu are explained. Depending on

the rights (set in the profile of users), some options may or may not be visible.

Information

The following functions are available under the "Information" sub-menu:

Notifications

The notifications menu shows the alarm and / or system events that are still present in the system's memory. The

messages can be deleted using the "Delete all" function key, provided the alarm situation has been removed. If

notifications cannot be deleted, a new notification will be given.

Open inputs

Using this menu option, it is possible to see which inputs (sensors) are still open (in alarm).

Section status

The status section is displayed in this option. An open circle indicates section is disarmed, a flashing circle

indicates section not ready to arm, a closed circle means section armed.

Event log

The last 1000 system events are stored in the Event log menu and cannot be deleted. By selecting a log line with

function key "Select", detailed information can be displayed if available.

System info

This screen shows the software version of the system and the IP address.

UNii manager key

This screen shows the unique key of your UNii security system. The installer needs this key to connect to the UNii

manager tool to program the system.

Overtime

With this option an overtime time can be programmed for the automatic arming function, if used. Select the

correct time switch from the list and enter the time you would like the system to stay disarmed.

(Un)-Bypass

A list of inputs is displayed in the bypass menu, a selected input can be bypassed or un-bypassed. By bypassing

an input, it is temporarily disabled. Not all inputs can be bypassed, this is determined by the installer during

installation.

User manual UNii Rev.2.11 – 14-07-2022 10

Users

In the user menu you can, if permitted, modify your own user settings, or create a new user (only possible for

supervisors). Depending on the UNii control panel model, the system has a maximum of 2,000 users. A code

consists of 6 digits, with which 999,999 different code combinations can be made. A code with only 000000 is

invalid.

In the usermenu the following main options are available:

-Change own data.

-Edit existing user.

-Add user.

Add user

Only possible for a user with administrator rights (Default this is User 1), this is normally only the supervisor of the

system. A new user code can be created with this option. You will be asked twice to enter the new (PIN) code.

After the (PIN) code has been created, the user settings can be changed via the "Change own data" or via the "Edit

existing user"

Edit existing user

Only possible for a user with administrator rights (Default this is User 1). If the 'Change existing user' is selected, a

list of users is shown in the display. Use the arrow up (key 2) and arrow down (key 8) to find the desired user and

press the key or "Select" function key to view and / or modify the settings for this user.

If tags are used to arm and disarm the system, the user can also be searched in the system by presenting his /

her tag. Once the list of users is displayed press the "Search" function key and present the tag to the reader on the

keypad, the display will now jump to the user associated with this tag. Press the key or "Select" function key to

view and / or modify the settings for this user.

The following user settings are present in the ‘Change own data’ of ‘Edit existing user’ menu’s:

Change name

Change the username. The username is displayed in the logbook and reported to a monitoring station.

Change code

Change the PIN-code you use to arm/disarm the system. The code cannot be changed to a code that already

exists or to a duress code. The code 000000 code is an invalid code.

Change code functionality

Changing the function of the (PIN) code. Options are:

•Code Direct arm and disarm

•Code to menu.

Code Direct arm and disarm ensures that all sections or groups linked to this user code are armed or disarmed

directly, Code to menu instructs the user to first select the section or groups and use the 'arm' or 'disarm' function

keys to arm or disarm the sections or groups.

Altri manuali per UNii

Indice

Lingue:

Altri manuali alphatronics Sistema di sicurezza

alphatronics

alphatronics AlphaVision ML Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente

alphatronics UNii Manuale utente

Manuali Sistema di sicurezza popolari di altre marche