ALTAI VX200 Manuale utente
1
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Altai VX200Dual-Band CPE/AP
_____________________________________________
Qui
ck Setup Guide
Version 1.1
2
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Introduction
Thank you for purchasingthe Altai VX200 product. This guide
providesinstructions to install the product and set it up as CPE (Station mode)
with minimal effort.
Package Contents
12
3
4576
3
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
1 - -VX200 Main Unit;
-DC Terminal Block Connector (3-
Contact);
-Chassis Ground Screw (Phillips, 3
x 6mm, with Square Washer)
1 pc
2 35mm DIN-railMounting Kit 1 pc
3 Wall-mounting Plate 2
pcs
4 Wall Mount Anchor & Long Screw
(Phillips, 3 x 19mm) 4
pcs
5 Short Screw (Phillips, 3 x 5mm)
(For both DIN-rail Mount and Wall
Mount)
6
pcs
6 Foot Pad (For Desk Mount) 4
pcs
7 Quick Setup Guide 1 pc
4
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Hardware Overview
Front View Right Side View
Top View Bottom View
Back View Left Side View
A
G
D
E
F
C
B
H
I
J
5
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
A: LED Panel
Power Off: No power
Flashing: AP booting up
Steady:AP boot up finished and ready for
service
LAN (Ethernet) Off: LAN (Ethernet) disconnected
Flashing: Data transmitting/receiving
2.4G/5G WiFi Radios
(Station/Repeater/
AP/Bridge Mode)
Off: Radio disabled
Steady:
1. Station/Repeater Mode on but not
connected to remote AP
2. AP Mode on but with no clients
associated
3. Bridge Mode on but not connected to
remote peer
Flashing:
1. Station/Repeater Mode on and
connected to remote AP
2. AP Mode on with clients associated
3. Bridge Mode on and connected to
remote peer
B: RP-SMA RF Port 1 (Female)
Used with Port 2 together to attach 2 x 2.4G/5G antennae (purchased
separately) for 2x2 MIMO WiFi connection.
6
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
C: Reset Button
Serves two functions below.
Reboot: Press and hold the Reset Button for 1-2 seconds until the power
LED blinks once.
Factory Reset: Press and hold the Reset Button for 5-8 seconds until the
power LED blinks twice consecutively.
D: RS232 DB9 SerialPort (Male)
Used to connect with a peripheral RS-232 serial device so that you can
access the serial device, via the VX200, from anywhere over TCP/IP network.
E: Ethernet Port (PoE In)
Used to connect to power source (seelater section forPower Options) and
provides 10/100/1000 Mbps network interface for LAN connection.
F: DC Terminal Block Receptor (3-Contact: Ground/+/-)
Used to connect to DC power source (seelater section forPower Options).
G: RP-SMA RF Port 2 (Female)
Used with Port 1 together to attach 2 x 2.4G/5G antennae (purchased
separately) for 2x2 MIMO WiFi connection.
Power LED Indicator
0s
Factory Reset
Reboot
1-2s 5-8s
7
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
H: Ground Point
Used for AP chassis grounding. Use size 14 AWG of ground wire (not included)
and attach it to the chassis with the provided ground screw. Connect the
other end of ground wire to a reliable earth ground point at site.
I: Screw Holes for Wall Mount
See later section forInstallation Options.
J: Screw Holes for DIN-rail Mount
See later section forInstallation Options.
Setup Requirements and Preparation
A computer with web browser: Google Chrome, Mozilla Firefox, or
Microsoft Internet Explorer 8 (or above)
Two Cat 5e/6 Ethernet cables
Aground wire (AWG: 14) for chassis grounding
Three wires (AWG: 12 – 24) for DC power; Or alternatively an 802.3af/at-
compliant PoE switch to power up VX200
Two 2.4G/5G external antennae (not provided)
Screw drivers (Phillips, and flat-blade) and a drill
Ground Point
Ground Screw
Ground Wire
(size of 14 AWG
recommended)
8
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Installation Option 1: DIN-Rail Mount (For 35mm Rail)
To mount the VX200 unit on the rail, follow the steps below.
1. Drive the short screws to attach the DIN-rail mounting bracket to the back
of the unit.
2. Insert the upper bracket lip into the DIN rail. Make sure the rail lies
between the bracket body and the spring.
3. Press the unit towards the rail until it snaps into place.
To remove the VX200 unit from the rail, follow the steps below.
1. Press the unit down so that the lower bracket
lip slightly detaches from the rail.
2. Pull the unit out to remove it from the rail.
Bracket
Spring
Rail
2
3
3
1
1
2
9
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Installation Option 2: Wall Mount
1. Drive the short screws to attach the two wall mounting plates to the unit.
2. Determine where the device is to be placed and mark location of the
mounting holes on a wall surface. Use an appropriate drill bit to drill the
holes, each with 1/3” (8.1mm) in diameter and 1” (26mm) deep, on the
markings.
3. Insert the anchors into the holes.
4. Insert the long screws through the mounting plates into the anchors.
5. Tighten the screws to secure the unit in place.
Four-Hole Installation
2
3
4Wall
5
Wall
10
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Power Options and Cable Connection Instructions
Follow one of the options below to power upVX200 for configuration.
-DC input:12~48VDC 1.25A
- PoE input:54VDC, 0.6A
Option 1: 12-48 VDC Power
1. Insert Ground/DC positive/DC negative wires (recommended AWG range: 12 -
24) into the terminal block. Use a small flat-blade screwdriver to tighten the wire-
clamp screws so as to prevent the wires from loosening.
VX200
V-
V+
Ethernet Cable
Two-Hole Installation
2
3
4Wall
5
Wall
Indice
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
