Altera USB-Blaster Manuale utente
Copyright © 2004 Altera Corporation. All rights reserved. Altera, The Programmable Solutions Company, the stylized Altera logo, specific device des-
ignations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and
service marks of Altera Corporation in the U.S. and other countries. All other product or service names are the property of their respective holders. Al-
tera products are protected under numerous U.S. and foreign patents and pending applications, maskwork rights, and copyrights. Altera warrants
performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make
changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the ap-
plication or use of any information, product, or service described herein except as expressly agreed to in writing by Altera
Corporation. Altera customers are advised to obtain the latest version of device specifications before relying on any published in-
formation and before placing orders for products or services.
Printed on recycled paper
ii Altera Corporation
Altera Corporation iii
Contents
Chapter 1. Setting Up the USB-Blaster Download Cable
Introduction ............................................................................................................................................ 1–1
Device Support ................................................................................................................................. 1–1
Power Requirements ........................................................................................................................ 1–1
Software Requirements ................................................................................................................... 1–2
Hardware Setup ..................................................................................................................................... 1–2
Software Setup ....................................................................................................................................... 1–3
Installing the USB-Blaster Driver ................................................................................................... 1–3
Setting Up the USB-Blaster Hardware in the Quartus II Software ........................................... 1–5
Chapter 2. USB-Blaster Specifications
Overview ................................................................................................................................................. 2–1
USB-Blaster Connections ...................................................................................................................... 2–1
Voltage Requirements ..................................................................................................................... 2–1
Cable-to-Board Connection ............................................................................................................. 2–2
USB-Blaster Plug Connection ......................................................................................................... 2–2
Circuit Board Header Connection ................................................................................................. 2–4
Operating Conditions ........................................................................................................................... 2–4
References ............................................................................................................................................... 2–6
Revision History .................................................................................................................................... 2–7
How to Contact Altera .......................................................................................................................... 2–7
iv Altera Corporation
USB-Blaster Download Cable User Guide
Contents
Altera Corporation 1–1
December 2004 Preliminary
Chapter 1. Setting Up the
USB-Blaster Download Cable
Introduction The USB-Blaster™download cable interfaces to a standard USB PC port.
This cable drives configuration data from the PC to the device. Because
design changes are downloaded directly to the device, prototyping is
easy and multiple design iterations can be accomplished in quick
succession.
Device Support
The USB-Blaster download cable allows you to program and configure
Altera®devices. Specifically, you can do the following:
■Download configuration data to FPGA devices:
●Stratix®II, Stratix GX, and Stratix family of devices
●Cyclone™II and Cyclone family of devices
●APEX™II and APEX 20K family of devices
●ACEX®1K devices
●Mercury™devices
●FLEX™10K, FLEX 10KE, and FLEX 10KA family of devices
●Excalibur™devices
■Download configuration data to User Flash Memory (UFM) devices:
●MAX®II family of devices
■Download configuration data to EEPROM-based devices:
●MAX 3000 and MAX 7000 family of devices
■Perform in-system programming of advanced configuration devices:
●EPC2, EPC4, EPC8, EPC16, and EPC1441 devices
■Perform in-system programming of serial configuration devices:
●EPCS1, EPCS4, EPCS16, and EPCS64 devices
In addition, the USB-Blaster download cable supports target systems
using 5.0 V TTL, 3.3 V LVTTL/LVCMOS, and single-ended I/O
standards from 1.5 V to 3.3 V.
Power Requirements
The USB-Blaster download cable requires the following power sources:
■5.0 V from the USB cable
■Between 1.5 V and 5.0 V from the target circuit board
1–2 Altera Corporation
USB-Blaster Download Cable User Guide December 2004
Hardware Setup
Software Requirements
The USB-Blaster download cable is available only for Windows 2000 and
Windows XP systems.
Use the Quartus®II software version 4.0 or later to configure your device.
The USB-Blaster download cable also supports the following:
■Quartus II Programmer (for programming and configuration)
■Quartus II SignalTap®II Logic Analyzer (for logic analysis)
■Quartus II Programmer (standalone version)
■Quartus II SignalTap II logic analyzer (standalone version)
Hardware Setup This section describes how to install and set up the USB-Blaster download
cable for device configuration or programming.
1For plug and header dimensions, pin names, and operating
conditions, see Chapter 2, “USB-Blaster Specifications.”
Connect your USB-Blaster download cable to the circuit board as
instructed below.
1. Disconnect the power cable from the circuit board.
2. Connect the USB cable to the USB port on your PC and to the
USB-Blaster port.
3. Connect the USB-Blaster download cable to the 10-pin header on the
device board. Figure 1–1 shows the USB-Blaster download cable
and the circuit board connector.
Altera Corporation 1–3
December 2004 USB-Blaster Download Cable User Guide
Setting Up the USB-Blaster Download Cable
Figure 1–1. The USB-Blaster Download Cable
4. Reconnect the power cable to reapply power to the circuit board.
1The Found New Hardware wizard may open and prompt you
to install a new hardware driver. Close the wizard and install
the hardware driver using the instructions provided in
“Installing the USB-Blaster Driver” below.
Software Setup This section describes the following:
■Installing the USB-Blaster driver
■Setting up the USB-Blaster hardware in the Quartus II software
Installing the USB-Blaster Driver
This section describes how to install the USB-Blaster driver.
Before you begin the installation, verify the USB-Blaster driver is located
in your directory: \<Quartus II system directory>\drivers\usb-blaster
1If the driver is not in your directory, download the USB-Blaster
driver from the Altera web site:
www.altera.com/support/software/drivers
P
I
N
1
T
A
R
G
E
T
B
L
A
S
T
E
R
S
I
D
E
S
I
D
E
10-pin Female Connector
(connects to target printed
circuit board 10-pin male
header)
1–4 Altera Corporation
USB-Blaster Download Cable User Guide December 2004
Software Setup
To install the driver, follow the directions below:
1. For Window 2000, choose Settings > Control Panel (Windows Start
menu).
or
For Windows XP, choose Control Panel (Windows Start menu).
2. Click Switch to Classic View if necessary (Control Panel window).
3. Double-click the Add Hardware icon to start the Add Hardware
wizard and click Next to continue.
4. Select Yes, I have already connected the hardware and click Next.
5. Select Add a new hardware device from the Installed hardware list,
and click Next to continue.
6. Select Install from a list or specified location (Advanced) and click
Next to continue.
1Depending on your system, the wording of this option may
vary slightly.
7. Select Sound, video and game controllers, and click Next to
continue.
8. Select Have Disk and browse to the location of the driver on your
system: \<Quartus II system directory>\drivers\usb-blaster
Click OK.
9. Select Altera USB-Blaster and click Next to continue.
10. Click Next to install the driver.
11. Click Continue Anyway when the Hardware Installation warning
appears.
12. Click Finish in the Completing the Add/Remove Hardware Wizard
window. Reboot your system.
Altera Corporation 1–5
December 2004 USB-Blaster Download Cable User Guide
Setting Up the USB-Blaster Download Cable
Setting Up the USB-Blaster Hardware in the Quartus II Software
Use the following steps to set up the USB-Blaster hardware in the Quartus
II software:
1. Start the Quartus II software.
2. Choose Programmer (Tools menu).
3. Click Hardware Setup. The Hardware Settings tab of the Hardware
Setup dialog box is displayed. USB-Blaster is visible in the
Available hardware items list of the Hardware Setup dialog box, as
shown in Figure 1–2.
Figure 1–2. Hardware Setup Dialog Box
4. Click USB-Blaster to highlight it and then click the Select Hardware
button.
5. Click Close to close the Hardware Setup dialog box.
6. In the Mode list, select the desired mode (Programmer window).
Table 1–1 describes each mode.
1–6 Altera Corporation
USB-Blaster Download Cable User Guide December 2004
Software Setup
1The USB-Blaster supports the Joint Test Action Group (JTAG),
Passive Serial Programming, and Active Serial modes.
fFor details about programming devices and creating secondary
programming files, see the “Programming & Configuration” chapter of
the Introduction to Quartus II Handbook.
For further information, see the Programming module of the Quartus II
online tutorial.
For further information, refer to the following topics in the Quartus II
software Help menu:
■Changing the Hardware Setup
■Programmer Introduction
■Overview: Working with Chain Description Files
■Overview: Converting Programming Files
Table 1–1. Programming Modes
Mode Mode Description
Joint Test Action Group
(JTAG)
Programs or configures all Altera devices
supported by Quartus II software, excluding
FLEX 6000.
In-Socket Programming Not supported by the USB-Blaster.
Passive Serial Programming Configures all Altera devices supported by
Quartus II software excluding MAX 3000 and
MAX 7000 devices.
Active Serial Programming Programs a single EPCS1 or EPCS4 serial
configuration device.
Altri manuali per USB-Blaster
1
Indice
Altri manuali Altera Cavi e connettori
