Altinex Pop 'N Plug Tower PNP400 Manuale utente
DESIGNER SOLUTIONS
MANUAL PART NUMBER: 400-0109-006
Shown with a silver finish.
POP ‘N PLUG®TOWER
USER’S GUIDE
PNP400
DESIGNER SOLUTIONS
400-0109-0061
TABLE OF CONTENTS
Page
PRECAUTIONS / SAFETY WARNINGS................ 2
GENERAL..........................................................2
HANDLING ........................................................2
CLEANING.........................................................2
FCC NOTICE .....................................................2
ABOUT YOUR PNP400............................................ 3
TECHNICAL SPECIFICATIONS.............................. 3
PRODUCT DESCRIPTION ...................................... 4
APPLICATION DIAGRAMS...................................... 5
DIAGRAM1: TYPICAL SETUP ..........................5
DIAGRAM2: CUTOUT.......................................6
DIAGRAM3: TOP VIEW.....................................7
DIAGRAM4: FRONT VIEW................................8
DIAGRAM5: SIDE VIEWUP..............................9
DIAGRAM6: MOUNTING ................................10
DIAGRAM7: INSTALL ASECTIONAL PLATE .11
DIAGRAM8: CABLES/ACCESSORIES ...........12
INSTALLING YOUR PNP400................................13
OPERATION.............................................................14
INSTALL SECTIONAL PLATES.......................14
TROUBLESHOOTING GUIDE...............................14
ALTINEX POLICIES................................................14
LIMITEDWARRANTY/RETURN POLICIES.....14
CONTACT INFORMATION..............................14
DESIGNER SOLUTIONS
400-0109-0062
PRECAUTIONS / SAFETY WARNINGS 1
Please read this manual carefully before using your
PNP400 and keep it handy for future reference.
These safety instructions are to ensure the long life
of your PNP400 and to prevent fire and shock
hazards. Please read them carefully and heed all
warnings.
1.1 GENERAL
•There are no user serviceable parts inside.
Qualified ALTINEX service personnel must
perform all service on the PNP400.
1.2 HANDLING
•For best results, place the PNP400 on a flat,
leveled surface in a dry area away from dust and
moisture.
•To prevent fire or shock, do not expose this unit
to water or moisture. Do not place the PNP400
in direct sunlight, near heaters,or heat-radiating
appliances, or near any liquid. Exposure to direct
sunlight, smoke, or steam can harm internal
components.
•Handle the PNP400 carefully. Dropping or
jarring can damage the unit.
•Do not pull any cables that are attached to the
PNP400.
•Do not place heavy objects on top of the
PNP400.
•Do not use excessive force to push down on the
top of the unit.
•Be careful. Serious injury could result because
of the sharp edges inside of the PNP400.
•To turn off main power, disconnect the power
cord powering the PNP400outlets.
•We recommend using wall outlets with a Ground
Fault Circuit Interrupter (GFCI) for maximum
protection.
1.3 CLEANING
•Unplug the PNP400 before cleaning.
•Clean only with a dry cloth. Never use strong
detergents or solvents such as alcohol or
thinner. Do not use a wet cloth or water to clean
the unit. Do not open the unit to clean.
1.4 FCC NOTICE
•This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
•This equipment has been tested and found to
comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and if
not installed and used in accordance with
instructions found herein, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
•Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.
DESIGNER SOLUTIONS
400-0109-0063
ABOUT YOUR PNP400 2
PNP400
POP 'N PLUG TOWER
The PNP400 Interconnect Tabletop Solution is
designed for installation into a conference room
table. The PNP400 provides a means of connecting
audiovisual, network,and power sources into a
presentation system. It is ideal for use with
ALTINEX computer video interfaces like the
VA6804FC. The PNP400 can “pop up” into a raised
position to provide access to connectors,or it can
be lowered into a table when not in use. The
PNP400 uses a tower-type construction with a gas
spring to raise the interface into position above the
tabletop.
The PNP400 Interconnect has two openings on
either side of the unit, servicing both sides of a
table. Several optional sectional plates are
available for the following: AC power, computer
video (15-pin HD), composite video (RCA), audio
(RCA), computer audio (3.5 mm stereo),
phone/modem (RJ-11), RS-232 (9-pin D-sub),
network (RJ-45), etc. Contact the ALTINEX Sales
Department for additional information regarding
optional connectors.
The PNP400 Interconnect is designed for use with
tables ranging from 0.25-4.0 in (6-102 mm) thick.
The PNP400 comes in a standard matte black
finish. Custom finishes for the top of the PNP400
allow the unit to accent any tabletop and are
available on a custom order basis for an additional
charge.
TECHNICAL SPECIFICATIONS 3
Specifications are subject to change.
See www.altinex.com for up-to-date information.
MECHANICALPNP400 (standard)
Maximum Table Thickness 4.00 in (102 mm)
Minimum Table Thickness 0.25 in (6 mm)
Height Above Table (open) 2.909 in (74 mm)
Height Below Table Surface 5.760 in (146 mm)
Base Width 6.674 in (170 mm)
Base Depth 4.840 in (123 mm)
Finish Black
T°Operating 10°C-35°C
T°Maximum 50°C
Humidity 90%non-condensing
Table 1. PNP400 Mechanical
DESIGNER SOLUTIONS
400-0109-0064
PRODUCT DESCRIPTION 4
CHASSIS
BEZEL
POP-UP LID
GAS SPRING MOUNTING HOLES
FOR ACCESSORY PLATES
(front and back)
TABLETOP
THUMB SCREW
BRACKET
MOUNTING
DESIGNER SOLUTIONS
400-0109-0065
APPLICATION DIAGRAMS 5
DIAGRAM 1: TYPICAL SETUP
DESIGNER SOLUTIONS
400-0109-0066
DIAGRAM 2: CUTOUT
DESIGNER SOLUTIONS
400-0109-0067
DIAGRAM 3: TOP VIEW
7.860"
[200mm]
6.530"
[166mm]
DESIGNER SOLUTIONS
400-0109-0068
DIAGRAM 4: FRONT VIEW
2.909"
[74 mm]
5.760"
[146 mm]
6.674"
[170 mm]
DESIGNER SOLUTIONS
400-0109-0069
DIAGRAM 5: SIDE VIEW
2.909"
[74 mm]
5.760"
[146 mm]
4.840"
[123 mm]
Altri manuali per Pop 'N Plug Tower PNP400
1
Indice
