Alto Professional Stealth Wireless Manuale utente

User Guide

English ( 3 – 8 )

Guía del usuario

Español ( 9 – 14 )

Guide d'utilisation

Français ( 15 – 20 )

Guida per l'uso

Italiano ( 21 – 26 )

Benutzerhandbuch

Deutsch ( 27 – 32 )

Gebruikershandleiding

Nederlands ( 33 – 38 )

Appendix

English ( 39 )

User Guide (English)

Introduction

Thank you for purchasing the Alto Professional Stealth Wireless system. Stealth Wireless is a

convenient way to carry an audio signal from the main mixing and listening location to your powered

loudspeakers. Compatible with any active loudspeaker, this system can be used to simplify a new

installation or to retrofit an existing sound system. Welcome to the sound of wireless freedom.

Features:

•Wireless audio connectivity to active loudspeakers

•Replaces up to 200' of console-to-system cabling

•No compromise in audio quality

•Reliable UHF band; 16 selectable channels

•Adjustable squelch eliminates interference

•Dual-channel transmitter: two XLR-1/4" combo inputs

•Single-channel receivers: XLR output

•Grow your system using the Stealth Expander Pack (sold separately)

Box Contents

•Stealth Wireless Transmitter (x1)

•Stealth Wireless Receiver (x2)

•Hook and Loop Strips (for receivers)

•M10 Screws (x2)

•Machine Screws (x2)

•Power Adapters (x3)

•User Guide

•Safety & Warranty Manual

Support

For complete system requirements, compatibility information, and product registration, visit the Alto

Professional website: altoprofessional.com.

For additional product support, visit altoprofessional.com/support.

Important

CAUTION! Permanent hearing loss may be caused by exposure to extremely high noise levels. The

U.S. Government's Occupational Safety and Health Administration (OSHA) has specified permissible

exposures to certain noise levels.

According to OSHA, exposure to high sound pressure levels (SPL) in excess of these limits may result

in hearing loss. When using equipment capable of generating high SPL, use hearing protection while

such equipment is under operation. The table below defines exposure for a given duration.

HOURS PER DAY SPL EXAMPLE

890 Small gig

692 Train

495 Subway train

397 High level desktop monitors

2100 Classical music concert

1.5 102 Riveting machine

1105 Machine factory

.50 110 Airport

.25 or less 115 Rock concert

Transmitter Features

Rear Panel

1. Antennas – Place the antennas in a vertical position for best

results in transmitting the wireless signal. If the wireless signal

quality is poor, change the position of the antennas.

2. Combo Inputs – Connect balanced or unbalanced 1/4” or XLR

line-level sources here.

3. Power Connector –Connect the included 12V DC, 300 mA power

adapter here.

Front Panel

1. Power Button –Press this button to turn the

transmitter on/off.

2. Mono/Stereo Select –Adjust this switch to

change the wireless signal that is sent to the

receiver to be either mono/stereo.

3. Signal Clip Indicator –The LED will turn red when the signal is close to peaking (clipping).

Note: The LED will begin to flicker red at -4 dB before clipping and become solid red if clipping

occurs.

4. Channel Select –Adjusts the frequency band range.

•Match channels on the transmitter and receiver in order to get a signal.

•Watch the receiver’s AF indicator and RF indicator to make sure a signal is being received.

•If you receive interference, change to another channel until a clean signal comes through.

•To change the channel:

a. Press and hold the Channel Select button for approximately 1 second until the

channel number flashes.

b. While the channel number is flashing, tap the Channel Select button to cycle

through the 16 available channels. Set the transmitter and receiver(s) to the same

channel.

c. When the desired channel number is shown, wait for 3 seconds. When the channel

number stops flashing, that channel is now selected.

d. Use the Left/Right Selector switches to set which receiver receives the left and right

signals, since the left and right signals are sent on the same channel.

5. Trim – Adjusts the signal level.

POWER MONO/ STEREO

MIN MAX MIN MAX

CHANNEL

2 2 3

Receiver Features

Bottom Panel

1. Output –Connect this XLR output to the input of your speaker.

2. Power –Connect the included 12V DC, 300 mA power supply here.

Front Panel

1. Antenna – The wireless receiver’s 2 antennas receive the signal that is

sent from the transmitter. Place the antennas in a vertical position for the

best signal quality.

2. AF Indicator –When illuminated, this LED indicates that an audio signal is

being detected by the receiver. If this LED does not turn on, check your

power connection and channel settings and try again.

3. RF Indicator –When illuminated, this LED indicates that the receiver is

receiving a signal. If this LED does not turn on, check your power

connection and channel settings and try again.

4. Power Indicator –When illuminated, this LED indicates the unit is

powered on.

5. Channel Select – To change the channel:

a. Press and hold the Channel Select button for approximately 1 second until the channel

number flashes.

b. While the channel number is flashing, tap the Channel Select button to cycle through

the 16 available channels. Set the transmitter and receiver(s) to the same channel.

c. When the desired channel number is shown, wait for 3 seconds. When the channel

number stops flashing, that channel is now selected.

d. Use the Left/Right Selector switches to set which receiver receives the left and right

signals, since the left and right signals are sent on the same channel.

6. Power Button –Press this button to turn on the receiver.

Side Panel

1. Left/Right Selector –Selects which stereo channel the receiver receives from the

transmitter. This only applies if both receivers are being used in a stereo application.

On both receivers, set the switch to the appropriate positions that match the L/R

speaker configuration. The Trim controls are directly connected to the L/R receiver

settings.

2. Squelch – Sets a noise limit. Signals must come in above that noise limit in order to

pass through the squelch filter. There are three settings to choose from depending

on how much noise there is. Set this switch to the position that most effectively

eliminates noise while allowing the signal to come through.

Connection Diagrams

Single Channel Setup

To send mono signals through the Stealth Wireless transmitter to a single receiver:

1. Connect your mixer’s main output to an input on the Stealth Wireless transmitter, and connect

the receiver’s output to your loudspeaker’s input. Keep all mixer volume and transmitter Trim

controls their minimum settings.

2. Power on the Stealth Wireless transmitter and receiver. Set their channels to matching numbers.

3. Adjust the transmitter and receiver antennas to a vertical position.

4. Set the transmitter to “mono” and adjust the Trim control to get a strong signal without clipping.

5. Turn on your loudspeaker, adjust the output level on your mixer, and adjust the Trim controls on

the transmitter to hear the audio signal. If you hear noise in the signal, change to a different

channel until a clean signal comes through.

Receiver

Powered

Speaker

Mixer

This diagram shows

the signal flow from a

mixer, through Stealth

Wireless, to a speaker.

Transmitter

Dual Channel Setup

To send stereo signals through the Stealth Wireless transmitter to two receivers:

1. Connect your mixer’s main outputs to the input channels on the Stealth Wireless transmitter, and

connect the Stealth Wireless receivers’ outputs to your loudspeaker’s inputs. Keep all mixer

volume and transmitter Trim controls at a minimum.

2. Power on the Stealth Wireless transmitter and receiver. Set their channels to matching numbers.

3. Adjust the transmitter and receiver antennas to a vertical position.

4. Set the transmitter to “stereo” and adjust the Trim controls to get a strong signal without

clipping.

5. Turn on your loudspeaker, adjust the output level of your mixer, and adjust the Trim controls on

the transmitter to hear the audio signal. If you hear noise in the signal, change to a different

channel until a clean signal comes through.

Transmitter

Receiver

Powered

Speaker Powered

Speaker

Receiver

Mixer

This diagram shows the

signal flow from a mixer,

through Stealth Wireless,

to speakers.

Speaker Mounting Diagram

See below for three ways to mount Stealth Wireless receivers to powered speakers:

1. M10 Screw: Use the supplied M10 screw to connect the Stealth Wireless receiver to the

powered speaker’s fly point.

2. Hook and Loop Strips: Use the Hook strip and Loop strip to mount the Stealth Wireless receiver

to any flat, stable surface.

3. Machine Screws: Caution: When using the supplied machine screws, check with a qualified

technician as improper installation can destroy internal speaker components.

Troubleshooting

No signal:

•Make sure both the transmitter and receiver are set to the same channel.

•Check the power LEDs on both the receiver and transmitter. If one of them is off, check that the

device’s power adapter is connected correctly.

•Make sure the volume controls on your mixer and speakers are turned up.

Weak signal:

•Make sure there are no objects (computers, walls, pipes, etc.) between the transmitter and

receivers.

•Change the channel on both the transmitter and receiver (to the same channel).

Poor signal quality:

•Make sure the receiver antennas do not touch each other.

•For best signal reception, provide at least 10 feet (3 meters) of separation between the

transmitter and the receiver.

•Keep any connected audio cables away from the antennas.

•Make sure no other devices are sending signals on the same frequency channel that you are

using.

•Change the channel on both the transmitter and receiver (to the same channel).

•Adjust the squelch control setting. A higher squelch setting provides better protection against

interference but may also reduce signal range. Choose a setting that most effectively mutes

interference yet allows the true signal to pass through. If poor signal quality requires a higher

squelch setting, try to eliminate the interference or switch the transmitter/receiver channel to

avoid a loss of signal range.

Mounting screw

Fly Point Hook Strip

Loop

Strip

M10 screw

Guía del usuario (Español)

Introducción

Gracias por comprar el sistema Stealth Wireless de Alto Professional. El Stealth Wireless es una

manera conveniente de transportar una señal de audio desde el lugar de mezcla y escucha principal

hasta sus altavoces alimentados. Compatible con cualquier altavoz activo, este sistema se puede

usar para simplificar una nueva instalación o retroinstalar un sistema de sonido existente. Bienvenido

al sonido de la libertad inalámbrica.

Características:

•Conectividad de audio inalámbrica a altavoces activos

•Reemplaza a hasta 60 m (200 pies) de cableado entre la consola y el sistema

•No compromete la calidad del audio

•Banda de UHF confiable, 16 canales seleccionables

•Silenciador de ruidos ajustable que elimina la interferencia

•Transmisor de doble canal: dos entradas combo XLR-1/4 pulg.

•Receptores monocanal: Salida XLR

•Haga crecer su sistema utilizando el Stealth Expander Pack (que se vende por separado)

Contenido de la caja

•Transmisor Stealth Wireless (1)

•Receptor Stealth Wireless (2)

•Fijación tipo Velcro (para receptores)

•Tornillos M10 (2)

•Tornillos para metal (2)

•Adaptadores de alimentación (3)

•Guía del usuario

•Manual sobre la seguridad y garantía

Soporte

Para obtener información completa sobre requisitos del sistema, compatibilidad y registro del

producto, visite el sitio web de Alto Professional: altoprofessional.com.

Para soporte adicional del producto, visite altoprofessional.com/support.

Importante

PRECAUCIÓN La exposición a niveles muy altos de ruido puede causar pérdidas auditivas

permanentes. La Administración de Seguridad y Salud Ocupacional del gobierno de EE.UU. (OSHA)

ha especificado los niveles de exposición permisibles a ciertos niveles de ruido.

Según la OSHA, la exposición a niveles de presión sonora (SPL) elevados que excedan estos límites

puede causar pérdidas auditivas. Cuando utilice equipos capaces de generar SPL elevados, use

protecciones auditivas mientras dichos equipos están en funcionamiento. La tabla siguiente define la

exposición en función de la duración.

HORAS DIARIAS SPL EJEMPLO

890 Música de bajo volumen

692 Tren

495 Tren subterráneo

397 Monitores de escritorio de alto nivel

2100 Concierto de música clásica

1.5 102 Remachadora

1105 Máquina fabril

.50 110 Aeropuerto

0.25 o menos 115 Concierto de rock

Características del transmisor

Panel trasero

1. Antenas – Coloque las antenas en posición vertical para

lograr los mejores resultados en la transmisión de la señal

inalámbrica. Si la calidad de la señal inalámbrica es

pobre, cambie la posición de las antenas.

2. Entradas combo – Conecte aquí las fuentes de nivel de

línea de 1/4 pulg. o XLR balanceadas o desbalanceadas.

3. Conector de alimentación –Conecte aquí el adaptador

de alimentación de 12 V CC, 300 mA incluido.

Panel frontal

1. Botón de encendido – Pulse este

botón para encender y apagar el

transmisor.

2. Selector mono/estéreo –Ajuste

este interruptor para cambiar la

señal inalámbrica que se envía al

receptor al modo mono o estéreo.

3. Indicador de recorte de señal –El LED se enciende con luz roja cuando la señal está cerca de

producir picos (recorte).

Nota: El LED comienza a parpadear en rojo a -4 dB antes del recorte y queda encendido

permanentemente si se produce el recorte.

4. Selección de Canal – Ajusta la gama de la banda de frecuencias.

•Haga coincidir los canales del transmisor y receptor a fin de obtener una señal.

•Observe el indicador de AF y de RF del receptor para asegurarse de que se reciba una

señal.

•Si recibe interferencia, cambie a otro canal hasta que obtenga una señal limpia.

•Para cambiar de canal:

a. Pulse y mantenga pulsado el botón de selección de canal durante

aproximadamente 1 segundo hasta que destelle el número de canal.

b. Mientras destella el número de canal, toque el botón de selección de canal para

recorrer los 16 canales disponibles. Ajuste el transmisor y el o los receptores al

mismo canal.

c. Cuando se muestra el número del canal deseado, espere 3 segundos. Cuando el

número de canal deja de destellar, significa que ese canal está seleccionado.

d. Use los interruptores selectores de sector izquierdo/derecho para configurar qué

receptor recibe las señales derecha e izquierda, puesto que las señales derecha e

izquierda se envían por el mismo canal.

5. Ajuste – Permite ajustar el nivel de volumen.

2 2 3

POWER MONO/ STEREO

MIN MAX MIN MAX

CHANNEL

Altri manuali per Stealth Wireless

Indice

Lingue:

Altri manuali Alto Professional Impianto stereo

Alto Professional

Alto Professional Stealth 1 Manuale utente

Manuali Impianto stereo popolari di altre marche

LG CM3330B Manuale utente

Sony

Sony SS-CEP50 Manuale utente

Cetacea Sound

Cetacea Sound CVS-II Manuale utente

Aiwa

Aiwa XR-H66MD Manuale utente

Denon

Denon UCD-250 Manuale utente

Sanyo

Sanyo DC-MX41i Manuale utente

Sharp

Sharp CD-ES600V Manuale utente

Exibel

Exibel BDX600-UK Manuale utente

Sanyo

Sanyo DC-F320 Manuale utente

Philips

Philips FWM583X Manuale utente

Sharp

Sharp CD-C462 Manuale utente

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Manuale utente

Aiwa

Aiwa XR-EM70 Manuale utente

Cyrus

Cyrus Lyric Manuale utente

Philips

Philips MCM159/98 Manuale utente

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Manuale utente

RCA

RCA RS3965SB Manuale utente

Sharp

Sharp XL-UH240 Manuale utente