Altronix VR6 Manuale utente
Rev. 050517
VR6
Voltage Regulator
Installation Guide
More than just power.TM
- 2 - VR6 Sub-Assembly
Overview:
Altronix VR6 voltage regulator is designed to convert a 24VDC input into a regulated 5VDC or 12VDC output.
For use with Maximal, eFlow, ULX, and Trove series of power supplies.
Specifications:
Agency Listings:
• UL 294 6th Edition: Access Control System Units.*
• ULC-S319: Electronic Access Control Systems.**
Power Input / Output:
• Input: 24VDC @ 1.75A – Output: 5VDC @ 6A.
Input: 24VDC @ 3.5A – Output: 12VDC @ 6A.
Output:
• 5VDC or 12VDC regulated output.
• Output rating 6A max. non power-limited.
• Surge suppression.
LED Indicators:
• Input and output LEDs.
Electrical:
• Operating temperature: 0º C to 49º C ambient.
• Humidity: 20 to 85%, non-condensing.
Mechanical:
• Product weight (approx.): 0.4 lbs. (0.18 kg).
• Shipping weight (approx.): 0.5 lbs. (0.23 kg).
*UL 294 Levels: Attack: I, Endurance: IV, Line security: I, Stand-by power: I.
**ULC-S319: Class 1.
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI,
with Canadian Electrical Code CSA C22.1, and with all local codes and authorities having jurisdiction.
Product is intended for indoor use only and should be installed by qualified personnel.
1. Mount VR6 in the desired location/enclosure.
Note: If VR6 needs to be elevated above the mounting surface, use included spacers (regular for VR6
only, male/female for mounting with PDS8/PDS8CB). Make sure to use metal spacer under the mounting
hole with star pattern (Fig. 2b, pg. 3).
2. Connect 24VDC power source to the terminals marked [+ IN –] (Fig. 1 pg. 2).
3. Select output voltage 5VDC or 12VDC using switch [S1].
4. Connect power distribution module to the terminals marked [+ OUT –] (Fig. 1 pg. 2).
VR6
Voltage Regulator
Altronix Corp.
Brooklyn, NY 11220
Made In USA
+ OUT --
+ IN --
ON-5V
OFF-12V
S1
24VDC
Power
Supply
5VDC or
12VDC
Output non
power-
limited
Fig. 1
VR6 Sub-Assembly - 3 -
Connecting PDS8/PDS8CB Board to VR6:
Refer to PDS8/PDS8CB Installation Guide Rev. 070116
1. Mount VR6 in the desired location/enclosure.
2. Plug-in male 8-pin connector to female 8-pin receptacle on VR6 board (Fig. 2a, pg. 3).
3. Fasten spacers (Fig. 2, pg. 3). Use metal spacer over mounting hole with star pattern (Fig. 2b, pg. 3).
4. Align 8-pin male connector with female receptacle of PDS8/PDS8CB, then mount (Fig. 2, pg. 2, Fig. 3a, pg. 4).
5. Connect 24VDC power supply to terminal marked [+ IN1 –] of PDS8/PDS8CB (Fig. 2, pg. 3).
6. Set each output (OUT1-OUT8) on PDS8/PDS8CB to route power from power supply 1 or 2
(jumper positions <1 OFF 2>) (Fig. 3, pg. 4).
Note: Measure output voltage before connecting devices. This helps avoiding potential damage.
7. Turn power off before connecting devices.
8. Connect devices to terminal pairs 1 to 8, marked [P (Positive) - OUT1-OUT8, N (Negative)] (Fig. 3, pg. 4).
Note: For DC devices carefully observe polarity.
9. After all devices have been connected turn power on.
Input/Output Chart:
Input 5VDC Output 12VDC Output
24VDC @ 1.75A 6A max. N/A
24VDC @ 3.5A N/A 6A max.
Pan Head
Screw
Metal
Spacer
8-Pin
Connector
Male/Female
Spacer
Spacer
Pem
Pem
PDS8/
PDS8CB
VR6
Metal
Spacer
8-Pin
Connector
Male/Female
Spacer
Pem
Pem
VR6
Pan Head
Screw
Metal
Spacer
8-Pin
Connector
Male/Female
Spacer
Spacer
Pem
Pem
PDS8/
PDS8CB
VR6
Metal
Spacer
8-Pin
Connector
Male/Female
Spacer
Pem
Pem
VR6
Fig. 2
Fig. 2b
Fig. 2a
C20
- 4 - VR6 Sub-Assembly
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
IIVR6 I11T MEMBER
PDS8
PDS8CB
Dual Voltage
Power Distribution
Module
Power
Supply 1
Power
Supply 2
+ INP1 --
PWR1 +
OFF
IN1
IN2
Out1
<1 off 2>
PWR1 +
PWR2 +
PWR2 +
COM (--- )
COM (--- )
+ INP2 --
IN2 Fuse
IN1 Fuse
Common Power Outputs (NEG)
N
P
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
10
10
3
3
333333
Out2
<1 off 2>
Out3
<1 off 2>
Out4
<1 off 2>
Out5
<1 off 2>
Out6
<1 off 2>
Out7
<1 off 2>
Out8
<1 off 2>
PDS8CB
(N) Negative DC outputs
(P) Positive DC outputs
Fig. 3 - PDS8(CB)
Fig. 3a
PTC rated
@ 2A
Indice
Altri manuali Altronix Controllori
Altronix
Altronix ACMS8 Series Manuale utente
Altronix
Altronix ACM4E Series Manuale utente
Altronix
Altronix PT724A Series Manuale utente
Altronix
Altronix Maximal series Manuale utente
Altronix
Altronix TROVE T2ZK7F8D Manuale utente
Altronix
Altronix ACM220 Series Manuale utente
Altronix
Altronix Maximal1RHD Manuale utente
Altronix
Altronix acm8cb Manuale utente
Altronix
Altronix StrikeIt1V Manuale utente
Altronix
Altronix MaximalV Series Manuale utente
Altronix
Altronix Maximal series Manuale utente
Altronix
Altronix Maximal1RHV Manuale utente
Altronix
Altronix Maximal3F Manuale utente
Altronix
Altronix AL400ULACM Manuale utente
Altronix
Altronix STRIKEIT2 Manuale utente
Altronix
Altronix Maximal Manuale utente
Altronix
Altronix eFlowNAD8V Series Manuale utente
Altronix
Altronix T2RM7CK1 Manuale utente
Altronix
Altronix StrikeIt1 Manuale utente
Altronix
Altronix ACM4 Series Manuale utente
