Altronix TROVE T1RM3F4V Manuale utente
Rev. T1RM3F4V080720 More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
Installation Guide
All registered trademarks are property of their respective owners.
T1RM3F4V
4 Door Kit with Fused Outputs
Fully assembled kit includes:
- Trove1R rack enclosure with Altronix and Mercury backplane (TM1R)
- (1) eFlow6NBV - Power Supply/Charger
- (1) VR6 - Voltage Regulator
- (1) PDS8 - Fused Dual Output Power Distribution Module
- (1) ACM4 - Fused Access Power Controller
T1RM3F4DV
4 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove1R rack enclosure with Altronix and Mercury/LenelS2 backplane (TM1R)
- (1) eFlow6NBV - Power Supply/Charger
- (1) VR6 - Voltage Regulator
- (1) PDS8CB - PTC Dual Output Power Distribution Module
- (1) ACM4CB - PTC Access Power Controller
Access & Power Integration
- 2 - T1RM3F4(D)V Installation Guide
Overview:
Altronix T1RM3F4V and T1RM3F4DV rack kits are pre-assembled and consist of Trove1M1R enclosure/backplane
with factory installed Altronix power supply/charger and sub-assemblies. These kits also accommodate various
combinations of Mercury/LenelS2 boards for up to four (4) doors in a single enclosure.
Configuration Charts:
Altronix
Model
Number
220VAC 50/60Hz
P/S Input Current (A)
Power Supply Board
Input Fuse Rating
Power Supply Board
Battery Fuse Rating
Nominal DC
Output Voltage Maximum Supply
Current for Main and
Aux. Outputs on
Power Supply board,
PDS8 Power
Distribution Module
and ACM4 Access
Power Controller’s
outputs (A)
Current Per
ACM4 Output (A)
ACM4Board
Input Fuse Rating
ACM4 Board
Output Fuse Rating
Fail-Safe/Fail-Secure or
Dry Form “C” Outputs
PDS8 Board
Input Fuse Rating
PDS8 Board
Output Fuse Rating
[DC] [Aux]
24VDC Output
Range (V)
24VDC Output
Range (V)
T1RM3F4V 2.5 5A/
250V
10A/
32V
20.28-
26.4
20.28-
26.4 24VDC @ 5.6A 2.5 10A/
250V
3A/
32V 410A/
32V
3A/
32V
Altronix
Model
Number
220VAC 50/60Hz
P/S Input Current (A)
Power Supply Board
Input Fuse Rating
Power Supply Board
Battery Fuse Rating
Nominal DC
Output Voltage Maximum Supply
Current for Main and
Aux. Outputs on
Power Supply board,
PDS8CB Power
Distribution Module
and ACM4CB Access
Power Controller’s
outputs (A)
Current Per
ACM4CB Output (A)
ACM4CB Board
Input Fuse Rating
ACM4CB Board
Output PTC Rating
Fail-Safe/Fail-Secure”
Outputs
PDS8CB Board
Input PTC Rating
PDS8CB Board
Output PTC Rating
[DC] [Aux]
24VDC Output
Range (V)
24VDC Output
Range (V)
T1RM3F4DV 2.5 5A/
250V
10A/
32V
20.28-
26.4
20.28-
26.4 24VDC @ 5.6A 2.5 10A/
250V 2.5A 4 9A 2.5A
Hardware and Accessories:
Specifications:
Agency Listings:
• CE European Conformity.
Mechanical:
• Black enclosure with ample knockouts for
convenient access.
• Includes: tamper switch, cam lock and
mounting hardware.
• Modular 2U standard EIA 19” drawer with
extendable slides up to 48”.
• Dimensions (H x W x D): 3.375” x 19.0” x 26.5”
(85.8mm x 482.6mm x 673.1mm)
Included Accessories:
• One (1) tamper switch
(Altronix Model TS112 or equivalent).
• Cam lock.
Available Accessories (not included):
• RE2: Rack Mount Battery Enclosure accommodates
up to four (4) 12VDC/7AH batteries.
• WM5, WM25, WM100: Magnetic Cable Tie Mounts
(5, 25, 100 counts).
Spacer | 5/16” Pan Head Screw | Lock Nut
T1RM3F4(D)V Installation Guide - 3 -
Installation Instructions for T1RM3F4(D)V:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local
codes and authorities having jurisdiction. These products are for indoor use only and must be installed within
the protected premises.
Note: First assemble and Install Z Bracket Wire Management Accesory
(refer to Z Bracket Installation pg. 4)
1. Remove backplane from enclosure prior to installing into rack cabinet
(do not discard hardware).
2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or
equivalent) turn the enclosure upside down. Punch out the knockout in
designated location, on the back of the unit, from outside of the drawer
(Fig. 1, pg. 3). Insert the tamper switch into the knockout from outside of the
drawer with the button facing outwards and spaded connectors inside the drawer.
Connect tamper switch wiring to the Access Control Panel input or the
appropriate UL Listed reporting device.
To activate alarm signal open the rack drawer.
3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.
4. Utilizing proper fasteners attach front ears to the rack rails.
5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.
6. Secure the rack cover (Fig. 2a, pg. 3) and rack drawer to earth ground (Fig. 2b, pg. 3).
7. Make sure that all internal cofigurations (wiring, voltage selection, switch settings, etc.) are
complete before mounting backplane back into enclosure.
8. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NBV and corresponding sub-assembly
Installation Guides for the following models: ACM4(CB), PDS8(CB), VR6 for further instructions.
Fig. 1
Back of the drawer,
viewed from outside.
Tamper Switch
mounting location
Fig. 2
Fig. 2a
Fig. 2b
- 4 - T1RM3F4(D)V Installation Guide
Assembling and Attaching
Z Bracket Wire Management Accessory (included):
Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory.
Hardware (included):
Ten (10) bolts and eight (8) lock nuts.
1. Carefully unpack Z Bracket. Do not discard hardware
(included) (Fig. 3, pg. 4).
2. Attach arms to each other using bolts and
lock nuts (Fig. 3a, pg. 4).
3. Attach the hinge brackets to the ends of
arms using bolts and nuts positioning
them as shown on (Fig. 3b, pg. 4).
4. Make sure that all nuts are tightened.
5. Attach the hinge bracket on the longer side of Z Bracket to the adjustable slide using bolts and lock nuts
(included) (Fig. 4, 4a, pg. 4).
6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts
(included).
Fig. 4
Fig. 4a
Fig. 3b
Two (2)
Fig. 3
Fig. 3a
T1RM3F4(D)V Installation Guide - 5 -
T1RM3F4(D)V: Configuration of Mercury Boards:
1. Fasten spacers onto metal pems configuration (A), (B), (C) or (D) of backplane depending on the access
controller (Fig. 5, pg. 5).
2. Position access controller module over corresponding spacers and fasten screws into spacers (Fig. 5a, pg. 5).
3. Mount backplane to enclosure with hardware.
Access Controller Position Chart for the Following Models:
Mercury/LenelS2 Access Controller Pem Mounting
LP1502, MR52, MR16IN, MR16OUT A
LP2500, MUX8 B
LP1501, MR62e C
MR50 D
Fig. 5
Altronix PDS8(CB)/VR6
OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
1 2 3 4 5 6 7 8
Common Power Outputs (NEG)
P
N
+ INP1 - + INP2 -
PWR1+
PWR2+
COM(-)
PWR1+
COM(-)
P
N
PWR1+
Altronix ACM4(CB)
--- +
Control
--- +
Power
NO C NC
FACP INTERFACE
+ INP --- T +RET ---
TRG
TRIGGER
INPUT
IN GND
1
NC C NO COM
OUTPUT 1
NC C NO COM
OUTPUT 2
NC C NO COM
OUTPUT 3
NC C NO COM
OUTPUT 4
IN GND
3
IN GND
4
IN GND
2
ACM4
ACCESS POWER
CONTROLLER
RoHS
MAIN
Altronix
eFlow6NB
AC
L G N
DCAC1 1min
enable
2hr.
disable
OFF - 24V
ON - 12V
ON
TRIGGER EOL
SUPERVISED
--- BAT+ --- DC +
NC C NO
AC FAIL
NC C NO
BATFA IL +AUX ---
NO GND
RESET
VR6 is mounted
under PDS8(CB)
A
C
D
D
C
B
B
A
To IEC connector
To LED lense
Pem
Spacer
Backplane
Pan Head Screw
Mercury Board
Fig. 5a
Altronix
eFlow6NBV
- 6 - T1RM3F4(D)V Installation Guide
Notes:
T1RM3F4(D)V Installation Guide - 7 -
Notes:
- 8 - T1RM3F4(D)V Installation Guide
Trove1R Enclosure Dimensions:
3.375” x 19.0” x 26.5” (85.8mm x 482.6mm x 673.1mm). Shown with Z Bracket attached.
0.1”
2.5mm
1.5”
38.1mm
11.175” (283.8mm)
2.4”
61mm
4.57”
116.1mm
3.375”
85.8mm
26.5”
673.1mm
19” (482.6mm)
R 1.27” (32.3mm)
1” (25.4mm)
0.55” (14mm)
3.62”
92mm
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
IIT1RM3F4(D)V I02U MEMBER
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Altronix Alimentazione elettrica
Altronix
Altronix Maximal series Manuale utente
Altronix
Altronix VertiLine563 Manuale utente
Altronix
Altronix AL300ULXD Manuale utente
Altronix
Altronix SMP10PM Manuale utente
Altronix
Altronix AL600ULX Series Manuale utente
Altronix
Altronix Vertiline24C Manuale utente
Altronix
Altronix LPS3AC Manuale utente
Altronix
Altronix AL400UL3 Manuale utente
Altronix
Altronix WayPoint10A Series Manuale utente
Altronix
Altronix eFlow102NB Manuale utente
Altronix
Altronix eFlow104NB Manuale utente
Altronix
Altronix ALTV244220 Manuale utente
Altronix
Altronix AL1024X220 Series Manuale utente
Altronix
Altronix AL175UL Manuale utente
Altronix
Altronix eFlow6N Manuale utente
Altronix
Altronix ALTV615DC8220 Istruzioni operative e di manutenzione
Altronix
Altronix VertiLine48MV Series Manuale utente
Altronix
Altronix SMP5 Manuale utente
Altronix
Altronix VB6 Manuale di servizio
Altronix
Altronix T2428100CP Manuale utente
