Alula RE703 Manuale utente

Doorbell Camera

Quick Start Guide

SAVE THIS MANUAL FOR FUTURE REFERENCE

Quick Setup

Power Kit Installation

Doorbell Mounting

Doorbell Setup

1

What's in the Box

Doorbell (x1)

Faceplate (x3)

Pick the one that

best matched

your home from

three faceplates.

Mounting Plate (x3)

Pick the one for best

surveillance angle.

Screwdriver (x1)

Plate Foam (x1)

Stabilize the

mounting plate when

installing it in the

rough surface. Drill Bit (x1)

Power Kit (x1)

Wire Harness (x1)

Fuse Wire (x1)

Wire Connectors (x4)

Mounting Screws (x3)

Anchors (x3)

Mini-Level (x1) U-shaped Wires (x2)

Security Screws (x2)

Fixing Screws (x2)

Doorbell Screws (x2)

Tools You May Need

Pencil

Drill

2

•If you have the mechanical chime in your home, start from Step 1 here.

•If you have the electronic chime in your home, please refer to its manual for detailed

operations.

•If you do not have any chime, skip power kit installation and follow the Option B in page 5.

2 Insert one end of the wire harness the power kit.

3 Remove the cover from your mechanical chime. 4 Remove the existing chime wires in

the terminals named TRANS and FRONT.

REAR TRANSF RONT

Power Kit Installation

1 Shut off the electricity at the breaker that

controls doorbell's circuit.

REAR TRANS FRONT

3

Wire Connector

Wire Harness

Chime Wire

Wiring Overview

DO NOT OIL

REAR TRANS FRONT

REAR TRANS FRONT

Chime Wire

7. Mount the power kit to the side of the chime.

Chime Wire

5 Connect the wire harness to the chime's

terminals named TRANS and FRONT.

6 Insert the existing chime wire and the other

end of the wire harness into the wire

connector and twist it tightly. Repeat this

step with the other chime wire.

8. Put back the chime cover.

4

2 (Optional) Paste the plate foam to the

mounting plate.

Mini-Level

Remove the mini-level when drill points are marked.

Use the plate foam when your wall is uneven.

4 Drill holes according to drill points

and insert anchors.

Anchor

5 Fix the mounting plate to the wall.

Mounting Screw

Doorbell Mounting

1 Shut off the electricity at the breaker that

controls doorbell's circuit.

3 Insert the mini-level into the mounting plate and

mark the drill points when its bubble stays in the middle.

5

6 If power kit is installed, follow Option A; If not, follow Option B.

Option A Connect doorbell with your existing doorbell wires.

Option B Connect the fuse wire with your existing doorbell wire.

Fixing Screw

U-Shaped Wire

Fixing Screw

U-Shaped Wire

6

7 Fix the doorbell to the mounting plate by

inserting the doorbell screws.

Doorbell Screw

8 Restore the electricity at the breaker.

Doorbell is powered on when its indicator flashes blue quickly. If not, make sure your electricity

is off and check the wiring. If yes, proceed to doorbell setup.

9 Add to Alula app.

- On the Cameras tab, tap “+” on the upper-right corner to go to the scan QR code page.

- Scan the QR code on the device or the cover of this manual when the indicator flashes blue.

- Follow the app wizard to finish Wi-Fi configuration.

If you want to change your camera's Wi-Fi, press and hold the reset button for 5s and repeat this part.

Doorbell Setup

7

10 Put the faceplate back and insert two security screws into the bottom of the doorbell to secure the

faceplate.

Security Screw

Appendix

Basics

Mounting Holes Terminals

micro SD

Card Slot

Reset Button

Hold for 5s to reset and

enter to AP mode.

LED Indicator

Blue Light Flashing Doorbell AP Mode is on.

Steady on Doorbell is working.

Red Light Flashing Fast Device Exception

Steady on Doorbell is powering on.

SD Card Management

If the memory card status displays as

Uninitialized, tap to initialize it.

Indice

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente