Ametek ABCE702-11R Manuale utente

Security II Rackmount Series

Uninterruptible Power Manager

For use with 700VA, 1000VA, 1440VA, 2200VA and 3000VA

2A01-00104 Rev A

1.0 - Introduction .................................................................... 6

2.0 - Safety Instructions ......................................................... 8

3.0 - Installation ..................................................................... 12

4.0 - Operation ....................................................................... 17

5.0 - Maintenance .................................................................. 22

6.0 - Troubleshooting ............................................................. 27

7.0 - Warranty ........................................................................ 29

8.0 - Specications ................................................................ 30

TABLE OF CONTENTS

A01-00104 Rev A

IMPORTANT NOTICE ON BATTERY WARRANTY

The warranty policy stated in Section 8 is not valid for applications in

which the UPM is regularly and intentionally disconnected from AC

mains power. The two year battery warranty applies only to products

that are properly installed and consistently connected to AC mains

power, except during utility outages.

Products regularly and intentionally disconnected from AC mains

power will experience substantially reduced battery life. The standard

warranty term does not apply in these cases and is supplanted by a

90-day warranty from time of shipment. The warranty provides for the

replacement of the battery or battery systems in the event that the

batteries do not meet performance specications as determined by our

company exclusively.

4A01-00104 Rev A

Danger- The danger symbol is used to indicate

imminently hazardous situations, locations, and

conditions which, if not avoided, WILL result in death,

serious injury, and/or severe property damage.

Caution- The caution symbol is used to in-

dicate potentially hazardous situations and

conditions which, if not avoided, may result in

injury. Equipment damage may also occur.

Warning- The warning symbol is used to indicate

potentially hazardous situations and conditions which,

if not avoided, COULD result in serious injury or

death. Severe property damage COULD also occur.

Attention- The attention warning symbol is used to

indicate situations and conditions that can cause

operator injury and/or equipment damage.

Other warning symbols may appear along with the

Danger and Caution symbol and are used to specify

special hazards. These warnings describe particular ar-

eas where special care and/or procedures are required

in order to prevent serious injury and possible death.

Electrical warnings- The electrical warning symbol is a

lightning bolt mark enclosed in a triangle. The electrical

warning symbol is used to indicate high voltage loca-

tions and conditions may cause serious injury or death.

Explosion warnings- The explosion warning

symbol is an explosion mark enclosed in a tri-

angle. The explosion warning symbol is used to

indicate locations and conditions where molten,

exploding parts may cause serious injury or death

if the proper precautions are not observed.

DANGER

CAUTION

WARNING

ATTENTION

A01-00104 Rev A

Alternating Current

Refer to instruction manual/booklet.

Two person lift.

6A01-00104 Rev A

1.0 INTRODUCTION

Thank you for your purchase of the Security II Series Rackmount UPM (

hereafter referred to as “UPM”). We manufacture two versions of the UPM

– a standard version, and a medical version listed to UL60601-1 and cUL

C22.2 No. 60601.1. In addition, all models are compatible with International

electrical distribution systems. International versions are UL listed (Medical

listed to IEC60601-1 and EN60601) and carry the CE Mark. We’ve prepared

this document to help familiarize you with the functions and controls of this

product. If, after reviewing this manual, you have any questions at all, please

feel free to contact our technical support team by phone (1-800-369-7179) or

email us at [email protected].

We are a global provider of power management solutions, headquartered in

Waukegan, Illinois, with international sales and distribution ofces in Swin-

don, United Kingdom, Toronto, Canada, Mexico City, Mexico and Germany.

All solutions incorporate a high energy surge diverter, a noise lter and a low

impedance isolation transformer. Together these components prevent pow-

er disturbances from destroying, degrading or disrupting system operations.

Registering your Product

Please take a few moments to register your product purchase. Registration

is easy and quick via the product registration page found on our website at

www.powervar.com.

A01-00104 Rev A

General

The Security II UPM (hereafter refered to as “UPM”) systems are the most

advanced, line interactive, true sinewave UPS products available for your

application. Each model is designed to provide total protection for your

system from a complete range of power quality problems. UPM systems will

protect your installation from normal mode voltage impulses, electrical noise,

sags, surges, brownouts, and blackouts. Each UPM contains a low imped-

ance isolation transformer, it completely eliminates common-mode (neutral-

to-ground) voltages that are a constant threat to the reliable operation of

microprocessor-based systems. When AC power is present, UPM constantly

lters and conditions the power supply. When AC power fails, the UPM uses

its internal, maintenance-free battery to supply reserved power to your com-

puter system. Regardless of whether or not commercial power is present, the

UPM is consistently on the job. Ensuring a fully conditioned, safely managed

interface between your computer system and its electrical power supply.

Figure 1 illustrates the basic operation of the UPM.

Figure 1

8A01-00104 Rev A

2.0 SAFETY INSTRUCTIONS

IMPORTANT - SAVE THESE INSTRUCTIONS

THIS MANUAL CONTAINS IMPORTANT SAFETY INSTRUCTIONS.

KEEP THIS MANUAL HANDY FOR REFERENCE.

CAUTION

A battery can present a risk of electrical shock. Short-circuit currents can

be extremely high and can create severe burns as well as the risk of re or

explosion from vented gases. Always observe proper precautions.

When replacing batteries, use the same quantity, rating and type of batteries

used by the company. The batteries used in this UPM are sealed lead-acid

and are maintenance free. Proper disposal of batteries is required. Refer to

your local codes for disposal of batteries.

UPM Rating Quantity and Battery Rating

700 VA 4 X 23W @ 12 VOLT

1000 VA 4 X 23W @ 12 VOLT

1440 VA 4 X 23W @ 12 VOLT

2200 VA 8 X 23W @ 12 VOLT

3000 VA 8 X 23W @ 12 VOLT

CAUTION

• This UPM contains voltages which are potentially hazardous. All re-

pairs should be performed by qualied service personnel.

• To reduce the risk of re, connect only to a circuit provided with 20 am-

peres maximum branch circuit over-current protection in accordance

with the National Electric Code, ANSI/NFPA 70.

• The UPM has its own internal energy source (battery). The output re-

ceptacles of the UPM may be live even when the UPM is not connect-

ed to an AC Supply.

A01-00104 Rev A

STATEMENT OF INTENDED USE

The medical UPMs are intended to protect medical, non-medical computer

equipment and medical devices that need battery backup, surge protection,

voltage regulation and line noise ltering in and around patient care areas.

Safe and continuous operation of the UPM depends partially on the care tak-

en by users. Please observe the following precautions. Not following these

could result in warranty being voided.

NOTE:

• The UPM is intended for stationary use.

• UPM is not intended for patient contact or for installation that will cause

accidental contact of patients.

• Do not use this UPM for life support applications in which a malfunction

or failure of the UPM system could cause failure or signicantly alter

the performance of a life-support device.

• Do not use this UPM near or around ammable gases. Do not use this

UPM within oxygen-enriched atmospheres.

• Do not disassemble the UPM.

• UPM is CLASS 1 equipment.

• Do not attempt to power the UPM from any receptacle except a proper-

ly grounded receptacle that matches the input plug provided with the

UPM.

• Do not place the UPM near water or in environments of excessive

humidity.

• Do not allow liquid or any foreign object to get inside the UPM.

• Do not block air vents on the front of the UPM.

• Do not plug appliances such as hair dryers, fans, heaters, etc. into the

UPM.

• Do not place the UPM under direct sunshine or close to heat emitting

sources (excessively warm temperatures will shorten battery life).

• This UPM is intended for installation in a temperature controlled, indoor

area free of conductive contaminants.

• The AC power source for the UPM should be conveniently near the

UPM and easily accessible – avoid extension cords or temporary pow-

er strips to power the UPM.

10 A01-00104 Rev A

• The total leakage current of the UPM and consumer connected equip-

ment should not exceed 3.5 mA for non-medical units.

• Not for use in a computer room as dened in the Standard for the

Protection of Electronic Computer/Data Processing Equipment, ANSI/

NFPA 75.

• The socket-outlet shall be installed near the equipment and shall be

easily accessible.

• The battery should be disconnected from the UPM by unplugging at its

quick connectors when maintenance or service work inside the UPM is

necessary.

• Do not dispose of batteries in a re – batteries may explode.

• Do not open or mutilate batteries. Doing so may release electrolyte or

other toxic substances, which may be harmful to the skin, eyes, or the

environment.

A battery can present a risk of electric shock and high short circuit current.

The following precautions should be observed when working with batteries:

• Remove watches, rings, or any other metal jewelry or objects which

may make contact with the battery.

• Use tools with insulated handles.

Unit is suitable for IT applications.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ametek UPS

Ametek

Ametek Surgex UPS-17202-53R Manuale utente

Ametek

Ametek Powervar Sinergy III 2kVA Manuale utente

Ametek

Ametek 387 Manuale utente

Ametek

Ametek UPS-I000-OL Manuale utente

Ametek

Ametek Powervar Security Plus II Manuale utente

Ametek

Ametek 420VA Manuale utente

Ametek

Ametek SURGEX Security Plus II UPS-42100-85R Manuale utente

Ametek

Ametek GUPS 2400A-107 Manuale utente

Ametek

Ametek Powervar Security II Series Manuale utente

Ametek

Ametek SurgeX UPS-1440-Li-ISO Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente