Amico LightMaster Multifunction Switch Manuale
Operating and Maintenance Instructions
LightMaster Multifunction Switch
www.amico.com
Contents
Introduction 3
Symbols Used in This Manual 4
Safety Instructions 5
Tool and Material Required 6
Installing the LightMaster Multifunction Switch 7-9
Mounting Drawings 10-11
Wiring Drawing 12-13
Disinfecting, Cleaning and Sterilization 14
Technical Data of the LightMaster Multifunction Switch 15
Warranty 16
www.amico.com 3
Introduction
Thank you for your purchase of the Light Master Multifunction Switch. This installation manual gives you instructions
on how to install the Light Master Multifunction Switch. Please read the following instructions very carefully and
follow the safety instructions and requirements.
4Amico Lighting Solutions
Symbols Used in This Manual
The warning symbols indicate all instructions that are important for safety. Failure to comply with them can lead
to injury, damage to the luminaire or the equipment. In combination with the following signal words the warning
symbols means:
Trademarks: All trade names mentioned in these instructions are the exclusive property of the relevant manufacturers.
DANGER Can lead to death or serious injury.
WARNING Can lead to injury.
ETL certication mark
www.amico.com 5
Safety Instructions
Intended use
The Amico LightMaster Multifunction switch is designed to improve day-to-day operation of your room lighting. With
advancements in room lighting, Amico has made it easy to operate each function of single or multiple light fixtures
with one intuitive keypad. Incorporated in a single gang space, the LightMaster keypad can control the Reading,
Ambient, Direct Light and Spot Lights that may be in the room. With infection control in mind, Amico uses a Mylar
Overlay on each keypad for ease of cleaning. The LightMaster keypad is also designed as a low voltage device to
ensure the highest levels of safety are met.
User Proles
No modifications can be carried out by the end user. Doing so will void warranty, ETL approval, and may cause severe
risks. Serviceable parts must be replaced with factory OEM parts. The user must comply with all building safety codes
and disinfection requirements.
Warning Levels
DANGER
Indication of hazards that can lead to death or serious injury if measures are disregarded.
WARNING
Indication of hazards that can lead to injury if measures are disregarded.
CAUTION
Indication of hazards that can lead to damage to property if measures are disregarded.
ELECTRIC SHOCK
The above is an electric shock warning symbol. Non-compliance with this symbol may result in damages or injuries
due to electric shock.
6Amico Lighting Solutions
Tools/Material Required
1. 1/8” Flat Head Screwdriver
2. #2 Phillips Screwdriver
3. Silicone Wire Nuts
4. Single gang electrical box for wall installation (Box provided with headwall)
NOTE: Before proceeding with the installation, make sure to remove the power to the electrical power supply.
Light Master Controller is mounted in electrical box or light xture as per the mounting drawing shown in this manual.
www.amico.com 7
Installing LightMaster Multifunction Switch
1. Remove 3 screws and take the cover o.
2. Connect the Master Controller input wires
(Black= Line/White=Neutral) to the line
voltage using silicone wire nuts.
NOTE: Do not turn the power on during the
wiring work.
3. Connect the ground wire from the main line
power to the ground wire in the xture.
8Amico Lighting Solutions
Installing the LightMaster Multifunction Switch
NOTE: Correct Polarity must be observed in order for the switch to operate. The Master Controller can be severely
damaged by reverse polarity. Ensure that all electrical connections are secured properly and have proper connection.
4. Connect low voltage output wires from
Master Controller to the keypad using silicone
wire nuts. Each keypad will connect to one
Red one Blue wire provided and labeled in
light xture. Wiring should be done as per the
wiring diagram provided.
5. Connect wires for loads and dimmings as per
provided wiring diagram.
6. Connect two wires from the Master
Controller low voltage output to the top
terminal block on the keypad. (The bottom
terminal block is used for the nurse call
pillow speaker connection only).
www.amico.com 9
Installing the LightMaster Multifunction Switch
7. Connect two wires from the nurse call to the bottom
terminal block in the keypad in order to operate two
functions through the pillow speaker. (Optional)
NOTE: The nurse call should be connected to only one
keypad in the room.
8. Once powered the keypads should communicate with
each other as shown below. After installing the keypad,
check all functions work properly.
10 Amico Lighting Solutions
Mounting Drawings
# 6 screws can be used to mount the Light Master controller and keypad.
LightMaster Controller
Security Power Unit
6.63"
3.82"
1.97"
0.31"
0.31"
6.24"
3.43"
Ø0.17"
Ø0.17"
1.97"
Indice
Altri manuali Amico Attrezzature mediche
Amico
Amico HMA-WT-LEDMNT Specifiche tecniche
Amico
Amico ALERT- 2 Manuale
Amico
Amico Exergen 134201 Manuale del prodotto
Amico
Amico ADULT 11 Manuale utente
Amico
Amico ATA-8-32 Manuale utente
Amico
Amico Diagnostic Station Manuale utente
Amico
Amico ICU Series Manuale
Amico
Amico Majestic Series Manuale utente
Amico
Amico Falcon Manuale utente
Amico
Amico Apollo MS-SC Manuale
Amico
Amico S-M-100 Manuale
Amico
Amico ARM Istruzioni per l’uso
Amico
Amico S-H-300 Manuale
Amico
Amico Mira LED Exam Light Manuale
Amico
Amico CS-SLVP-ADA-00 Manuale del prodotto
Amico
Amico Mira LED Exam Light Manuale
Amico
Amico Majestic Series Manuale utente
Amico
Amico GoLift Manuale utente
Amico
Amico Reflection Series Manuale utente
Amico
Amico AC-200C Manuale di installazione e funzionamento
