Amina FD39C Manuale utente
WIRELESS FISH FINDER
FOR BAITBOAT USING
OPERATION GUIDE
FD39C
-1-
Components list--------------------------------------3
Mounting the transducer----------------------------4
Assembling the transmitter-------------------------5
Powering the display ON ---------------------------8
Operational Instruction-----------------------------------8
What you see on screen-----------------------------8
Accessing menu features------------------------- ---9
Charge the battery of the receiver-----------------7
Assembling the receiver-----------------------------6
Remarks and Tips-----------------------------------------14
Specification-----------------------------------------------2
Installation guide -----------------------------------------3
Contents
-4 to 158°F (-20—70°C)
DC12V
200KHz
Depth Range Max :
Operational Temperature:
YesTransmitter Low Battery Alarm:
45 degrees
433MHz
Feet and meters
100ft (30.4M)
Specification:
Power Requirement of Receiver:
Power Requirement of
Transmitter:
Measure Units:
Sensor Beam Angle:
-2-
Depth Range Min : 2ft (0.6M)
Water Temperature Indicator: Yes
Radio Frequency:
400MOperational Range Max:
Sensor Frequency:
Backlighting : White LED
Display : FSTN LCD 128Vx64H
4-AA Rechargeable Batteries
Installation guide
-3-
1 Components list
1
3
2
5
4
8
6
910
7
11
1, Receiver
2, Power cable
3, Antenna of receiver
4, 4 "a" rechargeable battery of receiver
5, Charger of receiver
6, Transmitter
7, Power cable of transmitter
8, Antenna of transmitter
9, Sonar senser(transducer)
10
,
Ma
g
net for mountin
g
transducer
11, Tripod(optional)
-4-
2.2 Method II: Stick the magnet on the bottom of boat by glue (see
illustration), make the the magnet on the transducer magnetize with
the one on the boat.
Note: Tightening the screws.
2 Mounting the transducer
2.1Method I:Remove the cover under the bait boat, put the
transducer into the hole and keep the bottom of transducer to face
outside (see illustration), fixing it by the screws.
Note: Make sure the magnet is kept to be horizontal with
bottom of boat when it is fixed.
Fixing Magnet Magnetize
Remove Fixing
-5-
3.2 Assembling the antenna on the transmitter (see illustration).
3.1 Assembling the transmitter on the top of the bait boat (see
illustration).
2.3 Fixing the transducer signal cable on the tail of the bait
boat(see illustration)
3 Assembling the transmitter
3.3 Plug the transducer cable connector into the transmitter (see
illustration)
Fixing
Plug into
Plug into
3.4 Connect the power cable to the transmitter and socket of boat
power.
4.2 Assembling the antenna
4 Assembling the receiver
4.1 Installing the batteries
-6-
When you first use the Fish Finder you will need to installing the
batteries. Slide the Battery Door, and insert 4 "AA" batteries to
the battery compartment.
Be certain to align the batteries as per the diagram within the
battery compartment.
Plug the antenna into the socket on the back of display tightly(see
illustration)
Plug into
Plug into
Plug the power cable connector into the socket on the back of the
display tightly and another side to the battery compartment.
-7-
Plug one side of charger's cable
connector into the DC socket of
receiver, another side into the AC
power, the red indicator light and
charging is started. The indicator
turns green when power is full.
Warning!!! The chargers are different for transmitter and
receiver. Correct using must be requested according to the
instruction on the charger and this guide, otherwise the
damage will be caused!
4.3 Connecting the Power Cable
4.4 Assembling the tripod(tripod is optional)
5 Charge the battery of receiver
Screw the tripod in the screw thread socket on the bottom of
battery compartment tightly(see illustration)Screw tightly
Plug into
1 POWERING ON AND OFF
6 Water Temperature
Operation Guide
3 Sensitivity Indicator
-8-
2 WHAT YOU SEE ON SCREEN
Press and release POWER-MENU to power the unit on.
Press and hold POWER-MENU until the unit shuts down to power
off. When Unit powers on, the Start Up menu temporarily appears.
From this menu, select either Start-Up for on-the-water use, or
Simulation for learning to use the system with simulated sonar
data.
The Start-Up menu disappears after several seconds and the Unit
starts to work.
1 Water Surface Line
2 Battery Strength Indicator
9 Fish Icon with Fish Depth
5 Water Depth
8 Lower Zoom Range
7 Bottom Contour
4 Upper Zoom Range
4213
6
9
5
8
7
3.1 Light
-9-
3.2 Sensitivity
3 ACCESSING MENU FEATURES
NOTE: Continuous backlight operation significantly
decreases battery life on Unit Portables.
A easy to use menu system
accesses unit's adjustable
funtion.To activate the menu
system, press Menu Hot Button
directly to access main menus or
press POWER-MENU repeatly to
access all menus. When the
menu is on the display, use the
right and left keys to adjust the
menu. Menus automatically are
removed from the screen after
several seconds.
(Setting Saved in Memory)
When you press the LIGHT , the LIGHT menu temporarily appears.
Select either OFF or ON to activate the backlight at the desired
level.
(Setting Saved in Memory, 1 to 5)
When you press the SENSITIVITY , the SENSITIVITY menu
temporarily appears. Select a higher level to show smaller sonar
returns on-screen, or a lower level to remove clutter on the screen.
Indice
