AMobile IOT-800 Manuale utente
IOT-800
8" Risc-based Panel PC
User Manual
Version 1.0
Copyright Notice
Copyright © 2015 Amobile Intelligent Corp. All Rights Reserved.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order
to improve the reliability, design and function. It does not represent a commitment
on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.
III
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.Operation is subject to the
following two conditions:
1) this device may not cause harmful interference and
2) this device must accept any interference received, including interference that
may cause undesired operation of the device.
FCC RF Radiation Exposure Statement:
For body worn operation, this phone has been tested and meets FCC RF
exposure guidelines when used with an accessory that contains no metal and
that positions the handset a minimum of 1.5 cm from the body. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines.
1
Open Your Box
12.0 megapixel camera 11 Panel mounting holes
2Microphone 12 10/100 Mbps RJ-45 LAN port
35-point projected capacitive touch
screen 13 2 x USB 2.0 ports
4Integrated 2W speaker 14 DB-9 RS-232 port
5NFC antenna area* 15 DB-9 RS-232/422/485 port
64x 3.3V GPIO, 1 x CAN 2.0b / OBD-II 16 Power on/off toggle switch
72-pin DC terminal connector,
12V~24V auto-detection 17 4G antenna connector*
8microSD card slot 18 Wi-Fi / Bluetooth antenna connector
9Micro SIM (3FF) slot 19 3G/4G antenna connector*
10 UART Connector 20 VESA 75 mounting holes (M3 size)
*3G, 4G and NFC are optional modules and your IOT-800 may not come with these
components.
Package Contents:
IOT-800 8" Risc-Based Panel PC
2-pin Power Terminal Block Connector
Wi-Fi/Bluetooth Antenna
1M USB Cable
User Manual
17 18 19
4
5
1
7
6
8
20
2
3
9
10
11 11
12 13 14 15 16
2
Install microSD Card
Install SIM Cards & Antenna
To install a microSD card to the device, locate
the microSD card slot on the side and insert
the card following the direction as shown in
the picture. Push the card into the slot until it
locks into place.
SIM Card Installation
The IOT-800 accepts micro SIM (3FF) card.
To install a SIM card to the device, locate the
SIM card slot on the side and insert the card
following the direction as shown in the picture.
Push the card into the slot until it locks into
place.
3G/4G Antenna Connection
According to the type of mobile network supported by your IOT-800, attach
appropriate antenna to the IOT-800.
The IOT-800 comes with a Wi-Fi/Bluetooth
antenna to help increasing the signal strength.
To use the antenna, attache the Wi-Fi/
Bluetooth antenna to the Wi-Fi/Bluetooth
antenna connector.
Wi-Fi/Bluetooth Antenna Connection
To use 4G mobile network, attach
two 4G antennas as shown below.
To use 3G mobile network, attach one
3G antenna as shown below.
Wi-Fi/Bluetooth
Antenna
3G Antenna
4G Antennas
3
Power Connection
The IOT-800 comes with one 2-pin DC terminal block connector to connect power
to DC power connector on the device. To use the block connector:
1. Use a wire-stripping tool to strip both of the wires from the DC-input
power source. Expose the wire to the appropriate length for the DC power
connector.
2. Insert the wires into the DC power connector terminals and use a
screwdriver to tighten the two captive screws on the connector.
Pin Description
1Power_GND
2+12V-
3. Connect the DC terminal block
connector to the power connector
on the IOT-800.
4. Enable DC power by plugging
in the DC power supply cord to
a power source, or by enabling
power at the designated circuit.
After power connection, toggle the
power switch to ON to turn on the
device.
12
4
Connector Pinouts
PWPIN
Description: Power Input Connector
12
Connector Type: 2-pin Terminal Block
Pin Description
1Power_GND
2+12V-
GPIO and CAN Bus
Description: Digital General Purpose
Signal Input/Output and CAN
101
Connector Type: 4x 3.3V Digital GPIO
connector and 1 x CAN 2.0b Bus
Pin Description Pin Description
1IO_GND 6GPIO_4
2GPIO_1 7IO_GND
3GPIO_2 8CANL
4IO_GND 9CANH
5GPIO_3 10 IO_GND
Note: The pin assignments of other connectors conform to the industry standard.
Warning：
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation. changes or
modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
NOTE: This device and its antenna(s) must not be co-located or operation in conjunction with any
other antenna or transmitter.
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be
installed and operated with minimum distance of 20cm the radiator your body.
This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter
Altri manuali per IOT-800
1
Indice
Altri manuali AMobile Pannello touch
