Amonstar GLUE BINDING MACHINE Manuale utente
UKAS
QUALITY
MANAGEMENT
Registra tion No. 14-A
GLUE BINDING MACHINE
OPERATION MANUAL
1
1.Control section
1).This section consist of control panel , digital screen, key of “conrm”,”
+””-” ,etc .
2)”Txx” on digital screen indicate the environmental temperature before
heating .
2.Setting of temperature controller
1).Press the key of “ok”, video indicate setting temperature ,then adjust
the temperature to around 150 by pressing “+”, “-”.
2).seconds after nish setting ,the showing temperature
Notice
2
Notice
will back to current temperature and show
“HXX” .In the meantime ,relay pick-up and
glue box start heating ,the showing
temperature rise gradually and up to the
setting 150°during 15-20 minutes. The relay
close at this moment .Showing temperature
continue to rise then go down gradually till
1-3°under the setting , the relay pick-up and
heating again. Time after time ,the temperature
of melting glue can be maintained .The key
“ok ” should be pressed if temperature need
remain the
3.Turn on the machine after setting.same .
Phenomena Reason Solution
1 Indicate:ER-01 Thermal Tube
Malfunction
Replace thermal
tube
2 Indicate:er-02 Thermal couple
malfunction
Replace thermal
couple
List
List ......................................................... 1
Packing list and installation .................... 2
Precautious ............................................. 2
Operate parts ............................. 3
Operation manual(soft cover) ................. 4
Operation manual(hard cover) .................. 8
Adjustment of gluing roller .................... 11
Adjustment of milling blade ................... 12
Using of creasing setting ........................ 13
Using of hard back setting ...................... 14
Malfunctions, causations and solution .... 16
HONEST AND BOON
Thanks for choosing binding machine.
For operation easily and better binding result,
now promote new model of 4 machine, it is
binding, creasing, cutting perfect all in one.
Please read operation manual carefully before
operate. If any problem else, please contact
supplier.
Model Milling
cutter
Telmperature
controller
Hardback
setting
Creasing
setting
RD-JB-2
RD-JB-3
RD-JB-4
RD-JB-5
√√
√
√
√
√√√
3
√ √
√
√
Binding Machine Packing list Installation and Precautios
Packing list
1. 1 unit of machine
2. 1 set of soft cover template
3. 1 pcs of cable
4. 1 pcs of cross screw-driver
5. 1 pcs of M5 hexagonal socket spanner
6. 1 operate manual
7. 1 bag of glue
Installation
Please put this machine onto a stable worktop, avoid
approaching any humidity. Certain space should be kept to
operate the machine
Precaution
1. Connect to the specied power supply(220V/50Hz or 110V/60Hz).Open glue box cover, put in the solid glue. Note:
A.The glue should be clean and without any sundries.B Regularly add the glue particles into the glue box according to glue slurry
consumption. Thus a proper amount of glue slurry can be continuously supplied.
2. Turn on the switch, the glue to be heated under 170 degree about 15-20 minutes. During heating, don’t move the glue
box to avoid damage. Pay special attention to avoid the glue box touching hard thing during operating.
3. Make sure the template on the machine is accordant to the cover of binding file.(e.g. soft cover matches soft cover
template and hard cover le matches hard cover template)
4. Put the paddle on “N” position.
5. During the installation, if the gluing roller on the glue box is not parallel to the spine of the binding book, please adjust it
according to “Adjustment of the gluing roller” section in this manual. (page 11)
6. Milling cutter’s position can be adjusted by adjusting four screws. (page12)
4
OPERATION PARTS
图A 图B
long shaft
cap short handle
glue box
glue receiving tray
allocation shaft
round button
paddle
switch
push board
front bafe
pressure plate
short handle
backing board
temperature
controller
clamp plate
front board
milling cutter
handle
vernier adjust
bolt for gelatinize
Height adjust
bolt for gelatinize
adjust bolt for allocation shaft
Height adjust bolt for gelatinize
Height adjustbolt for gelatinize
fuse
outlet
5
Operation manual(soft cover)
1. Press the handle and draw out the
paper Pressurer
2 .Put the cover in-between the paper
pressurer and platform, and keep it
close to the localizer.The platform
could be raised so that the cover could
be easily placed.
3. Put the paper in-between the cover
and paper pressurer, piling it up neatly.
6
4. Push the paper pressurer down
against the paper and rotate the handle
up, locking the paper in as the picture
shows.
5. Press paddle down to “DN”
position, so that a crease can be made
on the bottom cover.And then push
paddle back to “N” position.
6. Push paddle to “UP” position, rotate
the platform upwards and make sure the
bottom side of les is at.
Operation manual(soft cover)
7
Operation manual(soft cover)
7. Push the milling cutter back and
forth on the bottom side of les
8. Gelatinize by moving glue box 9. After gelatinizing, Immediately
draught the back cover slightly by left
hand, press the paddledown to “N”
position by right hand, and then to
“DN” position, sustaining for around
6---8 seconds.
8
Operation manual(soft cover)
10. Push the paper pressurer down
against the paper and rotate the handle
up, turn the book to back face and put in
again, sustain about 3seconds
11. Press the handle down, draw the
paper pressurer open, and take out the
made-book. Cut the untidy edges of the
book to neatly by the paper cutter
9
Indice
