Anderson STACKPRO Series Guida all'installazione

DIAGNOSTIC GUIDE FOR STACKPRO

When navigating the pages you will see buttons that send you to the

corresponding procedures / sections of the troubleshooting table. You can also

use the shortcut from the table of contents (procedures) to obtain a specific

procedure. At any time you may click on the Anderson logo at the top of any

page to return to this page.

Table of contents
2
List of all sensors, functionnalities and location # 001
Search by « error code » what is my problem # 006
Search by « fault error » what is the problem # 011
How to test a sensor in order to know if it still work # 007
Protocol to inspect bad wired blowing up the fuses # 003
My stacked bales are falling down # 005
Protocol to install chain link with magnet on Stackpro 7200 #002
Adjusting the Danfoss variable displacement pump pressure and the main
valve relief pressure on a ECO80 valve # 004
Adjusting the Danfoss variable displacement pump pressure and the main
valve relief pressure on a PVG32 valve # 010
Electrical diagram 7200 2.0 # 008
Electrical diagram 5400 2.0 # 009

Model(s) : Stackpro
Bale are not 
centered on the 
loading table
Click here to 
continue
STACKPRO 5400
STACKPRO 7200
Bale carrier
Diagnostic procedure
Cannot get the 
Stackpro
started to work
Click here to 
continue
Problem with 
loading arm
Click here to 
continue
Problem with 
loading table
Click here to 
continue
Problem with 
bale pusher of 
the loading 
table
Click here to 
continue Problem with 
rolling fork
Click here to 
continue
Problem with 
unloading 
platform
Click here to 
continue
Problem with 
rear squizzer of 
the dumping 
table 
(Stackpro7200 
1st generation 
only)
Click here to 
continue
3
Problem with 
the rear-end 
pusher when 
unloading
Click here to 
continue
My stacked 
bale are falling 
down
Click here to 
continue
Search by “error 
code” what is 
my problem
Click here to 
continue
Search by “fault 
error” what is 
my problem
Click here to 
continue

Model(s) : Stackpro

Cannot get the

Stackpro started to

work

Bale carrier

Diagnostic procedure

The Stackpro dont

work when i engage

manually the lever

valve from the side

Click here to

Continue

The Stackpro move

when i engage the

lever valve from the

side, but cannot get it

move through the

Danfoss Controller

Click here to

Continue

The Danfoss touchscreen

dont want to turn ON.

Click here to continue

Model(s) : Stackpro

The Stackpro dont work when i

engage manually the lever valve

from the side

Bale carrier

Diagnostic procedure

Ensure your Danfoss

Controller is powered on

Make sure your Danfoss

Controller is « connected »

to the trailer

Make sure the Stackpro oil

tank is full as per factory

specification and oil tank

main valve is « open », and

your tractor PTO 1000 RPM

is engage

Make sure the loading arm

is in working position

From the Danfoss

Controller screen,

engage the « manual

mode » function. You

shall be able to use the

lever from the valve

From the Danfoss

Controller screen, I

engage the « manual

mode » function, but

i’m still unable to move

any function from the

controller, or from the

lever of the valve

Click here to continue 5

The Danfoss touchscreen

dont want to turn ON.

Click here to continue

Model(s) : Stackpro

The Stackpro move when i engage

the lever valve from the side, but

cannot get it move through the

Danfoss Controller

Bale carrier

Diagnostic procedure

Ensure your Danfoss

Controller is powered on

Make sure your Danfoss

Controller is « connected »

to the trailer

Make sure the Stackpro oil

tank is full as per factory

specification and main

valve is « open », and your

tractor PTO 1000 RPM is

engage

Make sure the loading arm

as been extended out

From the Danfoss

Controller screen, I

engage the

« automatic loading »

mode and everything

work.

From the Danfoss

Controller screen, I

engage the

« automatic loading »

mode but the screen

dont let me do it.

Click here to continue

The Danfoss touchscreen

dont want to turn ON.

Click here to continue

Model(s) : Stackpro

The Danfoss touchscreen display

dont want to turn ON

Bale carrier

Diagnostic procedure

Inspect the fuse located next to the

« kill switch » to turon ON/OFF the

computer. Replace if needed

The fuse is burned. I putted a

new one and it burned out

instantly when i turn the

computer ON

Protocol to inspect bad wired

blowing up the fuses #003

Use a voltmeter to test your battery

port connection. A minimum voltage

a 12V is required

Use a voltmeter to test your battery

port connection. A minimum voltage

a 12V is required for the touchscreen

Danfoss display to work properly.

Inspect the wires from the battery,

and search for a cutted wired, or

improperly inserted wired in the

connectors.

Model(s) : Stackpro

From the Danfoss Controller

screen, I engage the « manual

mode » function, but i’m still

unable to move any function from

the controller, or from the lever of

the valve

Bale carrier

Diagnostic procedure

Near the main valve, there is a

« load sensing » valve. Unplug

the electrical connector and test

if there is power coming out of

that connector.

There is NO power

coming out of that

connector.

There is Power

coming out of that

connector.

Inspect the wire

connection from

that connector up to

the power source

Use a screw driver to

bypass the « load

sensing » valve

Procedure #0000

While pressing on

the « load sensing »

valve bypass, i can

run the lever and

move any function

of the Strackpro

The load sensing

valve is broken and

need to be replace

Model(s) : Stackpro

From the Danfoss Controller screen, I

engage the « automatic loading »

mode but the screen dont let me do it.

Bale carrier

Diagnostic procedure

Verify that the loading arm as been fully extended out

to the right side, and you dont see the « LS Transport »

message on the main screen of the controller

The arm is fully

extended out to the

right, but i still see

the « LS TS » error

message on the main

screen.

Inspect the « LS

Transport » sensor

and make sure it is

powered and

functionnal when the

arm is extended.

The arm is fully extended

out to the right and the

« LS_TS » message DO NOT

appear on the main screen.

Go in the setting of the

controller under section

« bale corrector » and reset

the bale that is on the unit

if it show that it is fully

loaded. Often this is cause

by skipping some step

during the « unloading

mode »

When i engage the

« automatic loading »

mode, the computer screen

bring me automatically in

manual mode.

When i engage the

« automatic loading »

mode, the screen remain in

the « main screen menu »

You need to position

manually every Stackpro

movement accordingly so

at least one sensor of each

possible movement is

activate. It wont engage the

« automatic loading »

mode if one function is in

mid-run position. 9

Model(s) : Stackpro

Problem with

loading arm

Bale carrier

Diagnostic procedure

The bale are

slipping off the

loading arm

clamp when

Click here to

continue

The bale are

not centered on

the “loading

table”

Click here to

continue The bale hit the

loading table

before the arm

is horizontally

above the

loading table

Click here to

continue

The bale hit the

loading arm but

it wont pick it

automatically.

Click here to

continue

The loading

arm don’t want

to move down,

even when

running the

lever directly

Click here to

continue

Questo manuale è adatto per i seguenti modelli

Altri manuali Anderson Attrezzature agricole

Anderson

Anderson M-160 Manuale utente

Anderson

Anderson RB580 Manuale utente

Anderson

Anderson RBM1400 Manuale utente

Anderson

Anderson RBM Series Manuale utente

Anderson

Anderson RB 680 Manuale utente

Anderson

Anderson GB series Manuale utente

Anderson

Anderson Hybrid-X Guida all'installazione

Anderson

Anderson Fusion720 Manuale utente

Anderson

Anderson 680HS Manuale utente

Anderson

Anderson NWS-660 Manuale utente

Anderson

Anderson RBMPRO Guida all'installazione

Anderson

Anderson Fusion720 Manuale utente

Anderson

Anderson IFX720 Manuale

Anderson

Anderson RB-200 Manuale utente

Anderson

Anderson 590HS Manuale utente

Anderson

Anderson RB580 Manuale utente

Anderson

Anderson RB-200 Manuale utente

Anderson

Anderson WRAPTOR Manuale utente

Anderson

Anderson A-INL-032 Manuale utente

Anderson

Anderson TRB1000 Guida all'installazione

Anderson

Anderson NutriWrap 780 SB Manuale utente

Anderson

Anderson RB-200 Manuale utente

Anderson

Anderson Double stretcher Manuale utente

Anderson

Anderson ROUND BALE WRAPPER HYBRID Manuale utente

Manuali Attrezzature agricole popolari di altre marche

GSi

GSi PNEG-2314 Manuale utente

Checchi & Magli

Checchi & Magli TEXDRIVE Manuale utente

Amazone

Amazone Cenius 4003-2TX Manuale utente

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manuale utente

Cima

Cima BLITZ Istruzioni operative e di manutenzione

Amazone

Amazone CombiDisc 3000 Istruzioni per l'installazione

HE-VA

HE-VA Disc-Roller XL Contour Manuale utente

AGT

AGT AGT-SSFM Manuale utente

Milestone

Milestone 72-84 Manuale utente

KUHN

KUHN Hector 3000 Manuale utente

Krone

Krone X-Disc 6200 Manuale utente

Eliet

Eliet DZC450 Manuale utente

Taarup

Taarup BIO+ B4000 Manuale utente

Garland

Garland SHAKER 310 DPG Manuale utente

stable comfort

stable comfort StableWall System Manuale utente

Raven

Raven AccuBoom Manuale utente

International

International 710 Manuale utente

Ashland

Ashland HDW-3217-14 Manuale utente