Andersson BEH-G2000 Manuale utente
Blue Flame Heater
USER MANUAL
BEH-G2000
TABLE OF CONTENT /
INNEHÅLLSFÖRTECKNING /
INNHOLDSFORTEGNELSE
ENGLISH
Safety instructions 4-5
Overview 6
Operation 7-9
Maintenance 10
Specifications 11-13
Others 14
SVENSKA
Säkerhetsinstruktioner 15-16
Översikt 17
Användning 18-20
Underhåll 21
Specifikationer 22-24
Övrigt 25
NORSK
Sikkerhetsinstruksjoner 26-27
Oversikt 28
Bruk 29-31
Vedlikehold 32
Spesifikasjoner 33-35
Annet 36
4
SAFETY INSTRUCTIONS
Read the instructions before using this appliance
–This appliance requires installation by a competent
person.
–This appliance requires a hose and regulator, check with
your gas supplier.
–Use only in a well ventilated area.
–Do not use in leisure vehicles such as caravans and auto-
caravans.
–Refer to the instruction manual for exchange of gas
cylinder.
–In the event of gas leakage, the appliance gas supply shall
be turned o at the gas cylinder valve.
–Position the heater so that the heat is directed towards
the center of the room and, at any rate, towards an open
space; the front (radiant) part must be at least 2 meters
from curtains, sofas, furniture or other objects.
–After use turn o the appliance at the gas container valve.
–The room where the appliance is installed must have
enough air circulation for normal ventilation and
combustion.
–Advice that the appliance shall not be used in high rise
flats, in basements, bathrooms or bedrooms;
–The guard on this appliance is to prevent risk of fire or
injury from burns and no part of it should be permanently
removed. It doesn’t give full protection for young children
or the infirm.
–Do not move the appliance when operating, shocks and
5
bumps may activate the safety device.
–Do not operate the heater with the gas cylinder outside of
its compartment.
–The appliance should be 1 meter from the side wall.
–The heater must not be close to other sources of heat (at
least 1 meter away) or inflammable or explosive materials
and must not face objects that can be damaged or
burned (for example, not facing curtains, easy chairs or
furniture).
6
OVERVIEW
1. Front top panel
2. Front housing panel
3. Tank cover assembly
4. Wheels
5. Ignition button
6. Control knob
7. Gas valve
8. Gas pipe A
9. Electric ignition wire
10. Gas pipe B
11. Blue flame burner
12. ODS
(Oxygen Depletion System)
1
5
9
10
11
5
6
2
4
3
7
6
8
12
7
OPERATION
Installing:
1. Before assembly, make sure all packaging and transit protection
material is removed.
Note: After removing the heater from its packaging, check it for
damage: if you are unsure, do not use the appliance and contact
qualified service personnel. The packaging materials should not
be left within the reach of children because they are potentially
dangerous; dispose of them in conformity with the local regulations.
2. Unscrew the 2pcs M8 screws and washers which were pre-installed
on the base.
3. Insert the rear base into the slots of front base along the arrow
direction. Push on the rear base to fix it. Attach 2 pcs M8 screws and
washers.
4. Attach the tank cover to the slots in the housing side sections.
5. Install the battery
Remove the cap of ignition button by rotating it anti-clockwise. Install
1 piece AAA battery (not included). The negative end of battery goes
in first. Then replace the ignition button cap by rotating it clockwise.
8
Get started:
1. Open the valve on the gas cylinder.
2. To turn on, rotate the control knob to the
ignition position “ ”. Push down fully on the
control knob (this will allow gas to flow from
the pilot and the burner). While still holding
down the control knob fully, immediately
push the “IGNITION” button to light the
heater.
3. If the pilot does not ignite, release the control knob and “IGNITION”
button, wait 30 seconds and repeat the procedure.
4. Once the pilot is lit, continue to hold the knob for 20 seconds until the
heater remains lit.
Note: Do not hold the knob for longer than 40 seconds.
5. Push down and rotate the control knob to
(Max) or (Min) position to ignite the big blue
flame.
Note: Do not move the heater when it is
operating.
6. To turn o, push down and rotate the control knob to the ignition
position “ ”, and then completely shut o the valve at the gas
container.
9
Gas cylinder installation/replacement:
1. The appliance must only be powered with LPG gas less than or equal
to a 15 kg cylinder.
2. The regulator must be EN16129 approved and the hose must be
EN16436-1 approved with a length of 50 cm.
3. Connect one end of the hose to the pressure regulator and the other
end of the hose to the tap. Make sure that the connections are tight
and there is no damage to any component or fitting.
4. Before connecting the cylinder, make sure that its tap is closed and
there are no open flames (lit oven, etc.) in the vicinity and the gasket
seal is in good condition. Then screw the pressure regulator onto the
cylinder.
5. Attach the regulator to the tap, screw the nut tightly anti-clockwise.
6. Carefully check that there is no gas leaking from the connection
using soapy water (one part detergent and three parts water). If
there is a leak, bubbles will form; tighten the connection more or seek
professionally qualified service.
7. Place the cylinder in its compartment, taking care that the tube is not
twisted or choked and doesn’t touch any hot parts.
8. Align the rear cylinder cover onto the main body.
9. To replace the cylinder, make sure that its tap is closed and that there
are no open flames (lit oven, etc.) or sources of heat in the place
where you are working.
10. The hose used for this appliance must be replaced every two years.
11. Check the gas hose once per month and each time the cylinder is
changed, if it shows cracking, splitting or other deterioration, it should
be replaced with a new one.
12. Do not mishandle the connections or other components.
13. Do not turn the cylinder upside down to completely use its contents,
the releases liquid residues left in the tank that will irreparably
damage the heater.
10
MAINTENANCE
1. Keep exterior surfaces clean.
2. Clean the outside of the heater by using a soft cloth soaked with
water and a liquid detergent. Do not use scouring pads or abrasive
products.
3. Do not use water, inflammable or abrasive cleaners.
4. Regularly inspect the atmosphere analyzer and the aeration holes; if
there is dust or lint, remove it without damaging the burner or tubing.
5. Take care not to hit or damage the surface of the burner (it is
delicate), the fittings and gas tubes, the tap and all the other
components of the gas circuit.
6. We recommend that you have the heater inspected once a year by
authorized personnel.
7. If you decide not to use the heater for an extended period, it is a
good idea to follow the instructions below:
a. Close the tap on the cylinder and disconnect the regulator from the
cylinder.
b. Store the cylinder in a well-ventilated room, far from inflammable or
explosive materials and preferably outside your home; never store
the cylinder in a basement or attic.
c. The heater must be stored in a dry place and protected from dust
(and even better in its original packaging).
Indice
Lingue:
Manuali Stufa popolari di altre marche
Empire Heating Systems
Empire Heating Systems WCC65 Manuale utente
Wetekom
Wetekom 92 86 43 Manuale utente
Desa
Desa SPC170-F Manuale utente
Watlow
Watlow Watrod Electric Tubular Heaters Manuale utente
Haverland
Haverland ECO-DRY GPS Series Manuale elenco delle parti
Stelpro
Stelpro ASILVC2060 Series Manuale utente