Andover Controls xPDISPLAY Manuale operativo
SENSOR
DISPLAY
Keypad/Display Module
Installation & User Guid
e
Andover Controls Corporation
©2003, Andover Controls Corporation
All Rights Reserved
No part of this publication may be reproduced, read or stored in a retrieval
system, or transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without prior written permission of
Andover Controls Corporation.
Produced in the United States of America.
Infinity is a trademark of Andover Controls Corporation. All other trademarks
are the property of their respective owners.
xPDISPLAY Installation & User’s Guide, Version: A July, 2003
Andover Controls part number: 30-3001-839
The information in this book is furnished for informational purposes only, is
subject to change without notice, and should not be construed as a commitment
by Andover Controls Corporation. Andover Controls Corporation, assumes no
liability for any errors or inaccuracies that may appear in this document.
Andover Controls Corporation
300 Brickstone Square
Andover, MA 01810
(978) 470-0555
fax: (978) 470-0946
http://www.andovercontrols.com/
xPDISPLAY Installation & User’s Guide
Radio Interference
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to FCC CFR47 Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions in this manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Note
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
Avis
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la class A prescrites dans le
Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada.
Andover Controls Corporation
xPDISPLAY Installation & User’s Guide
Contents
Introduction ......................................................................1
xPDISPLAY Features .......................................................2
Mechanical Installation (Remote Version) .....................3
Expansion Bus Connection ............................................6
Pre-Operation ...................................................................7
Keypad ..............................................................................7
Setup Mode.......................................................................8
Display Configuration......................................................9
Plain English Display Manipulation..............................10
Display Programming ....................................................16
Keypad Programming....................................................19
Troubleshooting.............................................................21
Andover Controls Corporation
xPDISPLAY Installation & User’s Guide 1
TCX 865
xPDISPLAY
Keypad/Display Module
This manual describes the installation, care and use of the xPDISPLAY Module.
The Continuum xPDISPLAY Module provides a convenient, programmable interface to your
Continuum facility automation system. Authorized operators or tenants in your facility can
easily arm or disarm a security zone, quickly view HVAC or security information and/or
adjust personal comfort levels with little or no training.
The xPDISPLAY Module includes a four-line, 16-character backlit LCD display and a 21-
button ergonomically-designed keypad. The keys can be custom programmed using
Andover’s powerful programming language, Plain English®, to perform a wide variety of
functions, including switching a specific zone to occupied mode, signaling an alarm
condition, adjusting the amount of override time, and arming or disarming intruder alarm
points, utilizing password security.
Cost-effective and compact, the xPDISPLAY may be mounted directly on dry wall, or any
suitable electrical outlet box, and is intended for indoor use only.
2Andover Controls Corporation
xPDISPLAY Features
16 Character x 4 Line LCD Display with LED Backlight
21-key Custom Keypad with tactile feedback
3 programmable “soft” keys
Plain English software control of display backlight
Internally mounted within the i2920, b3920 or b4920 case (Internal Display)
Wall-mounted aluminum base with custom plastic cover (External Display)
xPDISPLAY Installation & User’s Guide 3
Mechanical Installation (Remote Version)
The module may be mounted directly on dry wall, or on any suitable electrical outlet box.
This module is for indoor use only and is not suitable for use where condensation may
occur.
1. Locate an appropriate area for the module.
2. Place the base plate on the surface of the wall area or electrical box where the
module is to be mounted and mark the location of the four mounting holes.
3. Drill the marked holes and insert wall anchors into the surface.
Note: Never drill directly into the mounting plate. Metal debris may enter and damage
the xPDISPLAY electronics.
4. If you are mounting the module to an electrical box:
Mount the base plate to the electrical box.
Temporarily hook the module to the base plate
as shown.
5. Guide the expansion cable from the controller through the opening in the back of the
module. Use the internal strain relief of the electrical box or the Heyco strain relief
supplied with the unit.
6. Expansion cable connection details can be found elsewhere in this manual.
Expansion
Cable
4Andover Controls Corporation
7. Mount the display to the base plate using the three supplied nuts as shown below.
8. Place the plastic cover over the module. The cover is fastened by inserting a #6
Allen tool (Andover Controls part # 30-3001-350) into the Allen fastener found at the
bottom of the case as shown. Turn the screw counter-clockwise, backing it out until
it is flush with the case.
Indice
