Andrew CommScope Argus Manuale utente

Argus

Installation

Instruction Manual, 353mm (13.9”) Profile Panel Antennas

General

This instruction manual contains all necessary information required to assist in the correct

installation of ARGUS Panel Antennas of 353mm (13.9") width to a 75 – 115mm (3" - 4.5")

diameter pipe when using the mounting kit with clamp bracket. These antennas can be

supplied with either fixed beam downtilt, manually adjustable electrical downtilt or AISG-

compatible remotely controlled electrical downtilt. Mechanical downtilt is also available if

required, depending on the type of mounting kit selected.

Following symbols can be found next to text outlining important information.

Please follow the procedure marked with this symbol precisely.

Non-compliance may lead to damage of the product.

Handy tips when installing product.

Unpacking

Make sure that the antenna and the accessory items listed below are provided and have not

been damaged during transport.

•Antenna

•Mounting kit (mounting kit components for each configuration are shown in Figures

2 and 3).

•Hex key 6mm AF (supplied with adjustable downtilt antennas only).

Mounting Kit

Type

600mm – 870mm

(23.6” – 34.3”)

Antennas

870mm – 1200mm

(34.3” – 43.3”)

Antennas

1200mm – 1575mm

(43.3” – 62”)

Antennas

1575mm – 2700mm

(62” – 106.3”)

Antennas

Fixed Downtilt F-042-GL-E F-042-GL-E F-042-GL-E F-042-GL-E

Mechanical

Downtilt T-095-GL-E T-045-GL-E T-041-GL-E T-029-GL-E

Tilt range 0°-15°in 3°steps 0

, 2

-10

in 1

steps 0°- 12°in 1°steps 0°- 8°in 1°steps

Mounting

Bracket Spacing

Dim A (Fig 4) 480mm (18.9") 716mm (28.2") 976mm (38.4") 1400mm (55.1")

Table 1: Mounting Kit Part Numbers for Different Antennas

Bulletin A997-0083 · Revision H · March 2015 page 1 of 7

CommScope Infrastructure Academy offers install

ation training

Instruction Manual, 353mm (13.9”) Profile Panel Antennas

Bulletin A997-0083 · Revision H · March 2015 page 2 of 7

DO NOT STACK

UNPACKED

ANTENNAS

DO NOT PLACE

POINT LOADS ON

ANTENNA RADOME

DO NOT USE ROPE

OR CHAIN OR SLING

ATTACHMENT

AROUND ANTENNA

FOR LIFTING

Installation Instructions

Ensure a torque spanner is used when tightening fasteners, see the mounting kit

diagrams on the following pages for the correct torque recommendations.

Ensure antenna is installed with the connectors at the bottom.

Bulletin A997-0083 · Revision H · March 2015 page 3 of 7

Instruction Manual, 353mm (13.9”) Profile Panel Antennas

USE MOUNTING

BRACKETS FOR

LIFTING AS SHOWN

Installation Instructions – Adjustable Downtilt Mounting Kit

T-029-GL-E, T-041-GL-E, T-045-GL-E, T-095-GL-E

Assemble mounting kits as per Figure 2 and 3 of this document.

1. Attach the mounting kit assembly to the antenna, before trying to clamp

the brackets to the pole.

2. Downtilt angles in 1°increments can be obtained with the correct

adjustment of the tilt arm bracket.

•Downtilt can be achieved by aligning the corresponding hole in the

tilt arm to the pivot bracket which mates against the mounting pole, as

shown in Figure 4. The first hole is for 1°downtilt*, with each consecutive

hole resulting in an increased inclination of 1°.

(*Note for the T-045-GL-E kit the tilt is 0°then 2°- 10°in 1°steps.

For the T-095-GL-E kit the tilt starts at 0°and increments in 3°steps)

•For finer downtilt angle adjustments the distance in between the top

and bottom mounting bracket on the pole can be adjusted.

•For 0°downtilt the tilt arm may be stowed as show in Figure 4.

•An inclinometer or other angular measuring device may be used to

verify downtilt angle as required.

The clamp brackets can clamp pipe diameters between 50 mm (2") & 115mm

(4.5"). For typical installations of antennas up to 1575mm (62") long the minimum

recommended pipe diameter is 60mm (2.4"). For antennas over 1575mm (62")

long the minimum recommended pipe diameter is 75mm (3").

Do not install near power lines. Power lines,

telephone lines, and guy wires look the same.

Assume any wire or line can electrocute you.

Do not install on a wet or windy day or

when lightning or thunder is in the area.

Do not use metal ladder.

Wear shoes with rubber soles and heels.

Wear protective clothing including a

long-sleeved shirt and rubber gloves.

Instruction Manual, 353mm (13.9”) Profile Panel Antennas

Bulletin A997-0083 · Revision H · March 2015 page 4 of 7

Upper Mounting Bracket Assembly

( To Suit Pipes OD 75-115 mm)

Lower Mounting Bracket Assembly

(To Suit Pipes OD 75-115 mm)

Figure 1: Correctly Assembled Mounting Kit Using Clamp Bracket for Mechanically

Adjustable Downtilt Antenna

Figure 2: Typical Exploded Assembly for Upper Mounting Bracket using Clamp

Bracket

Bulletin A997-0083 · Revision H · March 2015 page 5 of 7

Instruction Manual, 353mm (13.9”) Profile Panel Antennas

Figure 3: Exploded Assembly for Lower Mounting Bracket using Clamp Bracket

(This configuration should also be used for the upper Mounting Bracket when 0° tilt is

required)

Figure 4: Typical Example of Upper Bracket Placement for Various Downtilts

Operation of Antennas

Fixed Downtilt

Antennas The beam downtilt is factory set.

Manual

Electrically

Adjustable

Downtilt

Antennas

The beam downtilt below the horizon is adjusted by rotating the hex

socket located at the bottom of the antenna - Figure 5). Turning the hex

socket in a clockwise direction increases the beam downtilt below the

horizon. Turning the hex socket in an anti-clockwise direction decreases

the beam downtilt below the horizon. Beam downtilt setting in degrees

below boresight can be read off the scale at the base of the antenna.

The downtilt setting is read from the face of the antenna bottom end cap

at the point where the scale protrudes.

AISG Compliant

RET Antennas AISG Compliant antennas are compatible with AISG compliant control

unit equipment. For operation of downtilt using AISG compliant

controllers see the controller documentation. Where manual override of

RET control is provided at the antenna bottom end cap, operation is

identical to that described above for MET antennas.

WARNING: During downtilt adjustment ensure the hex socket is not

turned past the minimum and maximum positions as shown on the

downtilt indicator scale. Forcing the hex adjustment beyond this point

may lead to damage of the downtilt mechanism. Using power drills

and electric screwdrivers to adjust downtilt may also lead to

damage of the downtilt mechanism.

OPTIONAL: THE TILT ARM AND EXTRA HARDWARE

CAN BE STOWED IN THE POSITION SHOWN WHEN IN

0° DOWNTILT CONFIGURATION

USING A CLAMP

BRACKET.

Instruction Manual, 353mm (13.9”) Profile Panel Antennas

Bulletin A997-0083 · Revision H · March 2015 page 6 of 7

Port and Band

Identification

Each RF and/or AISG port on the antenna is numbered and identified in

accordance with AISG Standard “AISG Antenna Port Color Coding”.

Each RF band in the antenna corresponds with a pair of ±45° polarized

RF ports (an array), with the band numbers rising in step with the port

numbers, ie Band 1 corresponds with Ports 1 & 2, Band 2 corresponds

with Ports 3 & 4 etc.

Ports are numbered starting with RF low frequency band(s) first,

followed by higher frequency bands. For bands operating at the same

RF frequency, ports associated with arrays at the bottom of the antenna

are numbered before ports associated with arrays at the top.

For remote tilt antennas, depending on the configuration of AISG

employed, the antenna will report the bands differently to the primary

controller as follows:

SRET: For either AISG1.1 or 2.0, a multiband antenna configured as

cascaded SRET will report to the primary controller as multiple

antennas, each with a single band. Each band of the antenna will report

a different serial number. For example, a tri band antenna with serial

number 60051007 will report to the controller three individual antennas

with serial numbers 600510071, 600510072, 600510073, where the last

digit represents the band of the antenna.

MRET: When using AISG2.0, a multiband antenna will report to the

primary controller as a single antenna with multiple bands. Each band of

the antenna is accessible through the controller.

Remote

Electrical Tilt

Connection

RF Cable

Connection

The AISG connector fitted to the antenna is designed to accept any

AISG compliant cable assembly. After ensuring both connectors are dry,

push in the mating connector, then tighten the screw lock to between 0.7

and 1.1 Nm (0.5 -0.8 ft.lb). If needed or required by local procedures

apply mastic (or similar waterproofing) to the mating connectors.

Tighten the AISG mating connector by hand only. Do not apply any more

rotational force to the AISG mating connector than needed to properly

mate the seal and do not exceed 1.1 Nm. Using excessive torque may

damage the AISG connection in the antenna.

The 7-16 female connectors fitted to the antenna are designed to fit

jumper cables with a standard 7-16 RF male connector. After ensuring

both mating connectors are dry push the male connector in and tighten

the connector coupling to 23 - 28Nm (17 -21 ft.lb).

If needed or as required by local procedures a weatherproofing kit may

then be fitted to the connection.

If the RF connectors are tightened beyond the recommend torque the

RF connection to the antenna may be damaged.

Bulletin A997-0083 · Revision H · March 2015 page 7 of 7

Instruction Manual, 353mm (13.9”) Profile Panel Antennas

End Cap Layout for Typical Antennas

Figure 5: Typical 6-port

(CVVPX) with internal

bias tee on Port 1.

Figure 6: Typical 8-port

(CV3PX) with internal

bias tee on Port 1.

Note: The phase center of Band 4

is situated above that of Band 3.

Tilt adjust and scale

(Band 1)

Tilt adjust and scale

(Band

)

Tilt adjust and scale

(Band 3

)

Instruction Manual, 353mm (13.9”) Profile Panel Antennas

Bulletin A997-0083 · Revision H · March 2015 page 8 of 7

Figure 7: Typical 10-port

(RV4PX).

Note: The phase center of Band 4

(ports 7 and 8) is situated above

that of Band 2 (ports 3 and 4).

The phase center of Band 5 (ports

9 and 10) is situated above that of

Band 3 (ports 5 and 6).

CommScope Customer Service 24 hours

1100 CommScope Place SE P.O. Box 339, Hickory, NC 28603-0339 North America: +1-800-255-1479 (toll free)

(828) 324-2200 (800) 982-1708 Any country: +1-779-435-6500

www.commscope.com/andrew email: acicustomersupportcenter@commscope.com

Notice: CommScope disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.

Aviso: CommScope no acepta ninguna obligación ni responsabilidad como resultado de prácticas incorrectas o peligrosas de instalación, inspección, mantenimiento o retiro.

Avis : CommScope décline toute responsabilité pour les conséquences de procédures d’installation, d’inspection, d’entretien ou de retrait incorrectes ou dangereuses.

Hinweis: CommScope lehnt jede Haftung oder Verantwortung für Schäden ab, die aufgrund unsachgemäßer Installation, Überprüfung, Wartung oder Demontage auftreten.

Atenção: A CommScope abdica do direito de toda responsabilidade pelos resultados de práticas inadequadas e sem segurança de instalação, inspeção, manutenção ou remoção.

Avvertenza: CommScope declina eventuali responsabilità derivanti dell’esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.

注意: CommScope 公司申明对于不恰当或不安全的安装、检验、维修或拆卸操作所导致的后果不负任何义务和责任。

Indice

Altri manuali Andrew Antenna

Andrew

Andrew APC300 Manuale utente

Andrew

Andrew 4.9-Meter ESA Manuale

Andrew

Andrew CommScope Sentinel SHP 4 Series Manuale utente

Andrew

Andrew CommScope Metro Cell Series Manuale utente

Andrew

Andrew 75E LFL Antenna Manuale utente

Andrew

Andrew TYPE 100 Manuale utente

Andrew

Andrew DB201 Series Manuale utente

Andrew

Andrew Grid Sectional Parabolic Antennas Manuale utente

Andrew

Andrew 75E LFL Antenna Manuale utente

Andrew

Andrew 75E LFL Antenna Manuale utente

Andrew

Andrew OMACS3000 Manuale utente

Andrew

Andrew Type 960 Class I & II Manuale utente

Andrew

Andrew 7.6-Meter ESA Istruzioni operative

Andrew

Andrew 7.3-Meter ESA Istruzioni per l'installazione e il funzionamento

Andrew

Andrew ES45T Istruzioni per l'installazione e il funzionamento

Andrew

Andrew DB860 Manuale utente

Andrew

Andrew ValuLine VHLP2-10-IT1B Manuale utente

Andrew

Andrew TYPE 900 Manuale utente

Andrew

Andrew 3.7-Meter Earth Station Antenna Manuale utente

Andrew

Andrew OM24SNG-RC Guida all'installazione

Andrew

Andrew 960 .96 Meter Class II Manuale utente

Andrew

Andrew DB404 Manuale utente

Andrew

Andrew 18T Series Manuale utente

Andrew

Andrew 9.3-Meter ESA Manuale utente

Manuali Antenna popolari di altre marche

Alfa Network

Alfa Network APA-L01 Manuale utente

Naval

Naval PR-422CA Manuale utente

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuale utente

TERK Technologies

TERK Technologies TV44 Manuale utente

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuale utente

HP J8999A Manuale utente

MobilSat

MobilSat MSP-S Manuale utente

Steren

Steren ANT-UHF 13 Manuale utente

Novatel

Novatel 600-G Manuale operativo

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuale utente

TRENDnet

TRENDnet TEW-AO12O Manuale utente

Radio Shack

Radio Shack 15-1837 Manuale utente

CommScope

CommScope CMAX-OMFX-43M-I53 Manuale utente

Ramsey Electronics

Ramsey Electronics DAP25 Manuale utente

COBHAM

COBHAM SAILOR 800 VSAT Manuale per l'uso e la cura

Trango Systems

Trango Systems AD900-9 Manuale utente

Steren

Steren ANT-100 Manuale utente

Proxim

Proxim 5054-PA-23 Manuale utente