ANTAIRA Msc-116a Manuale utente

Congratulation on purchasing the high performance PCI multi-serial

host adapter. The adapter is high speed PCI bus based and

plug-and-play compliant. Its serial ports are fully 16C550 UART

compatible with most of the RS232C devices available from the

market.

Features:

Fully PCI Specifications 2.3 Compliant

Supports 16S RS232 ports over one single PCI slot.

16-byte deep FIFO per transmitter and receiver

Supports 5V or 12V on its VHDCI-68 connectors, provides an option to

supply power to all DB9 Connectors via the octopus cable

16C550 UARTs, Baud Rate up to 921.6Kbps

Automated in-band flow control using programmable Xon/Xoff in both

directions

Supports Windows 2000, XP, 2003, Vista, Win7 and Linux

16-Port RS-232 Multi Serial PCI Card

Installation Guide

1. Introduction

2. Board Layout

J3: Aux. Power

Connector

JP4: Aux Power

Source Selector

JP3, JP2: Power over External

Connector Enable/Disable

J1: S1~S8 VHDCI-68

External Connector

8-port VHDCI-68 to

DB9MX8 Octopus

Cables

S16

JP1: S1~S8 and

S9~S16 Swap

Jumpers

J2: S9~S16 VHDCI-68

External Connector

16-Port RS-232 Multi Serial PCI Card

JP3, JP2 and JP4 - External Power Selector: These jumpers were

used to provide the external power to the VHDCI-68 external

connector. JP3 enables or disables the power of S1~S8, JP2

enables or disables the power of S9~S16 over their octopus

cables. JP4 is used to select the power source (5V or 12V? from

PCI golden finger or J3 AUX power connector?).

JP3(JP2)

Settings

No power supplied to the VHDCI-

connector(s).

(default)

The VHDCI-

68 external connector will

be p

owered by the DC power source.

The power source will be determinted

by the JP1. The VHDCI-

68 octopus

cable will route the power to the pin

#9 of each DB9 male connectors

JP1

Settings

Internal 12V:

Power source is +12VDC,

from PCI golden finger (motherboard’

PCI slot)

(default)

External 12V: Power source is +12VDC,

from J2 AUX power connector.

External 5V: Power source is +5VDC,

from J2 AUX power connector.

3. Jumper Settings

DIS PWR

I5V

X5V

X12V

I12V

I5V

X5V

X12V

I12V

I5V

X5V

X12V

I12V

16-Port RS-232 Multi Serial PCI Card

Internal 5V:

Power source is +5VDC,

from PCI golden finger (motherboard’

PCI slot)

JP1- COM Ports Swapping Selector: These jumpers were used to

swap Serial Ports S1-S8 and S9-S16. Please keep them at the

default factory settings since it may confuse you about the COM

Port Numbers.

JP1

Settings

No Swapping. The COM ports will be

mapped to S1 to S16 normally.

(default)

The COM ports wil

l be swapped as

follows:

S1 S9

S2 S10

S3 S11

S4 S12

S5 S13

S6 S14

S7 S15

S8 S16

Note 1:

PLEASE DO NOT LET WINDOWS AUTO SEARCH THE DRIVERS ON THE CD, it will

cause problems because the INF files will be conflict in this case. Instead,

please browse to the correct location (folder) manually to make sure the

correct drivers are chosen and installed correctly.

Note2: Windows NT driver Installations

To install the Windows NT driver, please go into WinNT4 sub-directory and run

(double click) Install_Serial.exe to install all Serial Port Drivers.

I5V

X5V

X12V

I12V

4. Software Installation

16-Port RS-232 Multi Serial PCI Card

Type

Specifications

Connectors

Cable

Bus Interface

Number of Ports

RS-232 Signals

Baud Rate

Data Bits

Stop Bits

Parity

Flow Control

Power Requirement

Operating Temperature

Operating Humidity

Storage Temperature

VHDCI-68 Female X2

VHDCI-68M-to-DB9MX8 Octopus type

32-bit PCI

TXD, RXD, RTS, CTS, DTR, DSR, DCD, GND

110 bps to 921.6Kbps

5,6,7,8,9

1, 1.5, 2

None, Even, Odd, 1, 0

RTS/CTS, XON/XOFF

3.3V/800mA

0 to 55°C(32 to 132°F)

5 to 95% RH

-20 to 85°C (-4 to 185°F)

5. Specification

Drivers are in each

corresponding folder

Indice

Altri manuali ANTAIRA Scheda PCI

ANTAIRA

ANTAIRA MSC-102B1 Manuale utente

ANTAIRA

ANTAIRA MSC-202AL Manuale utente

ANTAIRA

ANTAIRA MSC-208A Manuale utente

ANTAIRA

ANTAIRA RS232 Manuale utente

ANTAIRA

ANTAIRA RS232 Manuale utente

ANTAIRA

ANTAIRA SC-102AL-1 Manuale utente

ANTAIRA

ANTAIRA MSC-102B1-SI Manuale utente

ANTAIRA

ANTAIRA MSC-202ALP Manuale utente

ANTAIRA

ANTAIRA MSC-202B1 Manuale utente

ANTAIRA

ANTAIRA Dual Channel Gigabit Ethernet PCIe Card Manuale utente

ANTAIRA

ANTAIRA MSC-204A2 Manuale utente

ANTAIRA

ANTAIRA msc-216a Manuale utente

ANTAIRA

ANTAIRA MSC-204A1-S Manuale utente

ANTAIRA

ANTAIRA RS232 Manuale utente

ANTAIRA

ANTAIRA MSC-204B1 Manuale utente

ANTAIRA

ANTAIRA MSC-102B1L Manuale utente

ANTAIRA

ANTAIRA MSC-202A-V2 Manuale utente

ANTAIRA

ANTAIRA MSC-104B Manuale utente

ANTAIRA

ANTAIRA msc-401a1 Manuale utente

Manuali Scheda PCI popolari di altre marche

ERMA

ERMA SSI 1417 Manuale utente

SIIG

SIIG CyberSerial Dual PCI Istruzioni per il montaggio

Moxa Technologies

Moxa Technologies CP-102E Manuale utente

I-Bus

I-Bus IBC2602 Manuale utente

Exsys

Exsys EX-60102 Manuale utente

Chelsio Communications

Chelsio Communications T5 Series Manuale utente

Conrad Electronic

Conrad Electronic 97 46 71 Manuale utente

Micro Innovations

Micro Innovations USB650A Manuale utente

KTI Networks

KTI Networks KF-310 Manuale utente

Asus

Asus SpaceLink WL230 Manuale utente

SIIG

SIIG SC2475 Manuale utente

TRENDnet

TRENDnet TEW-703PI Manuale utente

Belkin

Belkin F5D7000F Manuale utente

Pericom

Pericom PI7C7100 Manuale utente

ADLINK Technology

ADLINK Technology cPCI-3548 Manuale utente

Digium

Digium TE200 Series Manuale utente

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuale utente

Western Digital

Western Digital FireWire PCI Adapter Manuale utente

ANTAIRA msc-116a Manuale utente

Manuali Scheda PCI popolari di altre marche