Aperia Technologies Halo Connect GW-10 Manuale utente
Halo connect INSTALLATION
GUIDE for SLEEPER cab vehicles
© 2022 Aperia Technologies, Inc.
Aperia Technologies, Inc.
1616 Rollins Rd.
Burlingame, CA 91040
Phone: (650) 741-3231
Fax: (415) 524-2449
www.aperiatech.com
Document Number: 91-00008374 Rev. R01
June 2022
3
2
SAFETY WORDS AND SYMBOLS
Please pay attention to special symbols used through this manual to convey important information. Hazard sig-
nal words such as WARNING, CAUTION, or NOTICE are used throughout this manual. Information accented by
these words indicates a point of emphasis and importance. The following denitions comply with ANSI Z535.6
and indicate the use of signal words as they appear within this manual.
This is the safety alert symbol. It is used to alert you of potential physical injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING indicates a hazardous situation that, if not avoided, could result in serious
injury or death.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or
moderate injuries.
NOTICE is used to address practices which could result in damage to equipment or
property.
IMPORTANT SAFETY INFORMATION
The Halo Connect Gateway and its components should be installed in accordance with the instructions
in this manual. Proper installation of the Halo Connect system is critical to ensure safe use of the device.
Failure to do so may result in injury or death, damage to equipment, material or property. Carefully read,
understand and follow all safety related information within this manual.
Exercise caution when working with the vehicle power sources to avoid injury.
customer support
Phone +1 844-RUN-HALO
Website www.aperiatech.com
Sales [email protected]
Technical [email protected]
Contents
2 Important Safety Information
3 Section 1: Components & Tools
4 Section 2: Block Diagram & Install Layout
5 Section 3: Plan component installation
6 Section 4: Where to Find Power Sources
7 Section 5: Mount GPS antenna mounting and route cable
9 Section 6: Mount TPMS antenna
10 Section 7: Route GPS and TPMS antenna cables into the cab
11 Section 8: Apply gateway ID label to door
12 Section 9: Mount the gateway
13 Section 10: Connect power harness to vehicle
16 Section 11: Route cables and connect to gateway
18 Section 12: Prepare for activation
19 Section 13: Begin activation & install sensors
20 Section 14: Gateway activation workow
22 Section 15: Regulatory Information
1. Gateway
2. LTE antenna
3. GPS antenna
4. TPMS cable w/ antenna
5. Power harness*
6. Gateway ID label
7. TPMS sensor kit
Halo Connect system components
*Power harness connector will vary based on
vehicle type (RP1226 connector shown)
# TOOL/CONSUMABLE DESCRIPTION PURPOSE
1Small Impact Driver Self-tapping screws, cabin panels
2Bits for small impact driver (5/16 hex, phillips, torx) Self-tapping screws, various cabin panels
3 2-3" impact extension (compatible with small impact) Tool clearance - gateway screws
4 Drill Make cab access hole
51/2" drill bit or hole saw Make cab access hole
6 Debur tool Debur cab access hole
7Micro ush cutters Cutting zip ties
8 Channel lock pliers Tighten TPMS antenna onto cable
95/8" wrench Tighten TPMS antenna cable to bracket
10 Aperia SMA 4 in-lb torque wrench (P/N: TK-104SMA) Tightening SMA connections onto gateway
11 Mobile device (iOS or Android 6.0 or later) Activate gateway
12 Multimeter Check power source voltage
13 Misc. standard tools Gain access to dash and route cables
14 Isopropyl alcohol (or other residue free cleaner) Clean body panels for adhesives
15 1/4" loom Protect cable routed on exterior of cab
SECTION 1. Components & Tools
Required tools and other consumables
www.aperiatech.com
+1 (650) 741-3231
Model: GW-20
S/N: 031776
MAC: 11-22-33-44-EE-FF
Gateway Information
6
1
43
2
*
5
7
3
4
SECTION 2. BLOCK DIAGRAM & INSTALL LAYOUT
GATEWAY
GATEWAY
GPS
TPMS
TPMS
GPS
POWER
OPTION 2 POWER
OPTION 1
GATEWAY
POWER
OPTION 2
POWER
OPTION 1
GPS
TPMS
Install Layout Option 1
Alternative Layout
GATEWAY
GPS TPMS
TPMS
POWER
GATEWAY
GPS
TPMS
POWER
Gateway: On B-Pillar
GPS Antenna: On Dashboard
Power Source: Under Dashboard
TPMS Antenna: Low on rear of truck
Gateway: Under sleeper bunk
GPS Antenna: Top fairing bracket
Power Source: Under sleeper bunk
TPMS Antenna: Low on rear of truck
5
GPS
Transmissions are blocked by
metal, but will pass through
berglass, plastic, or glass.
Preferred Location: Top faring bracket or roof
Alternative Location: Top of dashboard
SECTION 3. PLAN COMPONENT InstallATION
GPS Antenna
TPMS
POWER
GPS
Preferred Source: Inverter power & ground studs
Alt. Source 1: Direct to battery
Alt. Source 2: Fuse panel
Power Source
TPMS Antenna
TPMS Antenna
Gateway
Cable routes & cab acess hole
GATEWAY
Gateway power source should be:
• Continuous, 12V or 24V power source
• Grounded to the vehicle chassis
• Find an existing cab access hole, or a location to
make a 1/2 inch hole, to route the external cables to
the inside of the cab.
• Power harness and externally mounted antennas
must have enough length to reach the gateway.
• Excess cable put into service loop and stored in an
open volume behind a trim panel or other safe spot.
• Right, Left, or Center of cab
• Points DOWNWARD
• Protrudes below bottom of cab
• Does not contact anything when
cab airbags deated.
GPS Antenna on top fairing bracket
min. 6" from vertical metal
Antenna performs best in
horizontal orientation
Preferred Location: Under sleeper bunk
Alternative Location: Behind seat
on B pillar panel
SECTION 4. WHERE TO FIND POWER SOURCES
Preferred Power Source: Power & ground studs on power inverter under bunk
Power Harness PN: CB-DC10A
3/8" ID ring terminals w/
5/16" ID conversion washers
Common location Vehicle Side Of Power Harness
Alternative Power Source 1: RP1226 Telematics Connector
KW T680
Pete 579
Volvo VN
Cascadia
Pete 579
Power Harness PN: CB-RPS16A and CB-RPS16A-P1
Common locations in dash* Vehicle Side Of Power Harness
Alternative Power Source 2: Fuse panel under bunk
Power Harness PN: CB-FT10A
Common location Vehicle Side Of Power Harness
6
*RP1226 connector became available as an
option in 2019 model years and is becoming a
standard feature in most class 7/8 tractors.
+
7
Step 5.1: Clean and prepare the GPS antenna mounting surface and cable routing area
A. Clean the surfaces where the GPS adhesive and adhesive cable tie mounts attach.
SECTION 5. MOUNT GPS ANTENNA AND ROUTE CABLE
• Avoid placing GPS less than 6" away from
any vertical metal plates, including the back
wall of the cab as it can aect GPS signal.
• DO NOT put tight bends in cable near anten-
na. Let the cables follow a natural path.
Too close to rear of cab (vertical metal)
1-4"
min. 6"
Step 5.2: Attach the GPS antenna
A. Apply loom to the GPS antenna cable.
B. Remove the 3M adhesive backing and place
the antenna in the desired location.
C. Secure cable with zip tie 1-4" from antenna.
D. Apply rm pressure to any adhesive mounted
components for approximately 15 seconds to
ensure optimal adhesion.
Preferred GPS Location: Top Fairing Bracket
Alternative GPS Location: On top of dashboard
GPS
Step 5.3: Route GPS antenna to bottom of cab
A. Route the loomed antenna cable to the bottom of the cab, towards the cabin access hole, securing
the cable at least every 12 inches.
GPS CABLE ROUTING GUIDELINES
• Do not bend or stretch antenna cables too tightly when routing.
• Keep a minimum bend radius of 1/2" for GPS to prevent signal transmission issues
• When routing the cables avoid sharp edges that may cut or abraid the cable or heat sources that
may melt the cable.
• Only attach adhesive cable tie mounts to flat, clean surfaces. Do not mount them on curved or dirty surfaces.
SECTION 5. MOUNT GPS ANTENNA AND ROUTE CABLE (CONT'D)
8
9
Step 6.1: Install TPMS bracket
A. Attach the provided TPMS bracket to the rear of the cab in your previously selected location. Be
sure the TPMS antenna will protrude below the bottom of the cab
Step 6.2: Attach TPMS antenna to bracket
A. Loom TPMS cable enough to reach to cab access hole.
B. Attach the TPMS antenna cable to the bracket and tighten.
TIGHTEN: Finger tight + 1 turn
C. Attach the TPMS antenna onto the cable then carefully tighten.
TIGHTEN: Finger tight + 1/4 turn, until snug.
The TPMS antenna
must be oriented pointing DOWN-
WARD to ensure good reception
from the TPMS sensors.
TPMS CABLE ROUTING GUIDELINES
• Do not bend or stretch antenna cables too tightly when routing.
• A minimum bend radius of 1" for TPMS must not be violated to prevent signal transmission issues.
• When routing the cables avoid sharp edges that may cut or abraid the cable or heat sources that may melt the cable.
• Do not use adhesive cable tie mounts on curved surfaces. Only attach them to clean, flat surfaces.
SECTION 6. MOUNT TPMS Antenna
Test t the TPMS antenna prior to attaching bracket
to make sure it will protrude past the bottom of the cab and will
not contact anything, even when cab airbags are deated.
TIGHTEN:
Finger tight + 1 turn
with 5/8" wrench
TIGHTEN:
Finger tight + 1/4 turn
with pliers
TPMS
Step 7.1: Find or make the cab access hole
A. Use the existing access hole located during the planning
step, or make a 1/2 inch access hole, in the bottom of the
cab to route cables for externally mounted antennas into
the cab.
CAB ACCESS HOLE GUIDELINES
• Conrm that no airlines, wiring, or other items on the exterior of the vehicle will be damaged when the drill punctures
the oor. Failure to do so may cause damage to the vehicle.
• The cab access hole should be in a location where stored items or foot trafc won't repeatedly smash or bend the
cable where it enters the vehicle.
SECTION 7. ROUTE GPS & TPMS ANTENNA CABLES INTO THE CAB
CAB ACCESS HOLE
10
Preferred cabin access hole: Exisiting grommeted hole
Alternative cabin access hole: Make 1/2 hole and use provide grommet
Questo manuale è adatto per i seguenti modelli
1
Indice
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
