ApexCCTV AP-16CO Manuale utente

Page 1 of 18

Network Configuration Guide

AP-9060/AP-16CO

Page 2 of 18

Table of Contents

TABLE OF CONTENTS.............................................................................................................. 2

GETTING STARTED .................................................................................................................. 4

INTRODUCTION............................................................................................................................... 4

DISCLAIMER ................................................................................................................................... 4

QUICK SETUP GUIDE (POWER USERS ONLY) .................................................................. 4

PLANNING.................................................................................................................................... 4

EQUIPMENT NEEDED ..................................................................................................................... 4

GATHERING INFORMATION........................................................................................................... 5

INFORMATION GATHERING CHECKLIST .......................................................................................... 7

YOUR ROUTER’S INTERNAL IP ADDRESS......................................................................................... 8

YOUR ROUTER’S PUBLIC IP ADDRESS.............................................................................................. 8

YOUR ROUTER’S USERNAME AND PASSWORD................................................................................. 8

YOUR NETWORK’S DHCP RANGE ................................................................................................... 8

YOUR NETWORK’S SUBNET MASK................................................................................................... 8

THE IP ADDRESS YOU WILL GIVE YOUR AP-9060/AP-16CO.......................................................... 8

YOUR AP-9060/AP-16CO’S USERNAME AND PASSWORD............................................................... 9

EXISTING PORT FORWARD /NAT INFORMATION............................................................................. 9

PITFALLS TO AVOID....................................................................................................................... 9

IP ADDRESSES IN YOUR DHCP RANGE........................................................................................... 9

DYNAMIC IP ADDRESSES ................................................................................................................ 9

USING DYNAMIC PUBLIC IP ADDRESSES WITHOUT DYNAMIC DNS............................................... 9

CONFIGURATION.................................................................................................................... 10

CONFIGURING YOUR AP-9060/AP-16CO................................................................................... 10

USER ACCOUNTS ........................................................................................................................... 10

NETWORK SETTINGS ..................................................................................................................... 10

CONFIGURING YOUR ROUTER .................................................................................................... 12

CHECKING FOR CONFLICTS........................................................................................................... 12

FINALIZING YOUR SETUP .............................................................................................................. 12

TESTING........................................................................................................................................ 13

TESTING FROM YOUR LAN (INTERNAL)........................................................................................ 13

TESTING FROM THE WAN (INTERNET).......................................................................................... 15

ADDITIONAL RESOURCES.................................................................................................... 15

NETWORKING............................................................................................................................... 15

DYNAMIC HOST CONFIGURATION PROTOCOL (DHCP) ................................................................ 15

Page 3 of 18

IP ADDRESSING ............................................................................................................................. 15

LOCAL AREA NETWORKS (LAN) .................................................................................................. 15

NETWORK ADDRESS TRANSLATION (NAT).................................................................................. 15

PORT FORWARDING....................................................................................................................... 15

PORTS ............................................................................................................................................ 15

ROUTING /ROUTER CONFIGURATION ........................................................................................... 16

SUBNET /SUBNET MASKING ......................................................................................................... 16

TRANSMISSION CONTROL PROTOCOL /INTERNET PROTOCOL (TCP/IP) ...................................... 16

USER DATAGRAM PROTOCOL ....................................................................................................... 16

WIDE AREA NETWORKS (WAN)................................................................................................... 16

FIREWALLS................................................................................................................................... 16

GENERAL INFORMATION ............................................................................................................... 16

COMMON PORT NUMBERS............................................................................................................. 16

SOFTWARE FIREWALLS ................................................................................................................. 16

Page 4 of 18

Getting Started

Introduction

Thank you for choosing ApexCCTV. We hope that this document will assist you in

configuring your new AP-9060/AP-16CO for use on your network and via the internet.

This document follows industry standard best practices, and while you do not need to

follow every single step on this list, doing so will provide you with a reliable and secure

connection to your AP-9060/AP-16CO.

Disclaimer

This document requires a basic understanding of networking principles including, but not

limited to, network address translation (NAT), transmission control protocol/internet

protocol (TCP/IP), user datagram protocol (UDP), subnet and subnet mask configuration,

dynamic host configuration protocol (DHCP), IP addresses, routing and router

configuration, public vs. private networks, etc…

The basic knowledge described above is outside the scope of this document, and will be

covered briefly or not at all, and only as it applies to an individual step you need to take

in configuring your AP-9060/AP-16CO. Please find other resources in the “Additional

Resources” section at the end of this document.

Quick Setup Guide (Power Users Only)

The gist of setting up your AP-9060/AP-16CO for network use is very straightforward.

1) Configure your AP-9060/AP-16CO with an appropriate network address (use best

practices).

2) Forward ports 80, 5000, 5001 through one or more routers, starting with your

internet gateway.

Planning

Equipment Needed

1) Your network enabled AP-9060/AP-16CO from ApexCCTV, with working

cameras connected.

2) The CD that came with your AP-9060/AP-16CO.

3) Your AP-9060/AP-16CO manual (may be on your CD)

4) A Television monitor, hooked up to the DVR.

5) A Network cable connecting your DVR to your network.

6) A router.

7) An additional PC on your network with Windows (Preferably XP) installed.

Page 5 of 18

Gathering Information

Before continuing, you will need to gather the following information. If you do not know

or cannot find some of this information, please contact your network administrator or

your internet service provider (ISP).

There is some specific network information you will need to have readily available

before you start configuring your network and surveillance product. You can find much

of this information (in Windows XP) by clicking Start ÆAccessories ÆCommand

Prompt. If there is no option under accessories for “Command Prompt,” you can also

click on Start ÆRun. A dialog box will appear:

Type “cmd” in the dialog box and click the OK button to continue. A command prompt

will appear that looks similar to this:

Once you have a command prompt up, type the following line and press the Enter key:

ipconfig /all

Page 6 of 18

You should have some information similar to what is below on your screen:

Please take special note of the Subnet mask, Default Gateway, and DNS Servers.

The complete list of information you will need is listed below. We recommend using the

checklist on the following page as you gather information to be sure you will have

everything you need before you begin. If you are unsure of how to find some of this

information, there are tips for each item following the Information Gathering Checklist.

Page 7 of 18

Information Gathering Checklist

Your router’s internal IP address

Your router’s public IP address

Your router’s username and password

Your network’s DHCP range

Your network’s DNS server addresses

Your network’s subnet mask

Your AP-9060/AP-16CO’s username and password

The IP Address you will give your AP-9060/AP-16CO

Existing forwarded ports or NAT entries from your router

Page 8 of 18

Your router’s internal IP address

This is typically the same as the “default gateway” from the above information.

Your router’s public IP address

You can find this by visiting www.whatismyip.com.

Your router’s username and password

If you do not know this information, you will need to look in your router’s manual or

contact your network administrator or internet service provider. If you have not changed

your router’s default username and password, you can probably find it on the internet.

Try looking at your router, jotting down its manufacturer and model number, and then

doing a search on Google for the model number, plus “default username.” For instance,

if my router is a D-Link DFL-200, I would search for:

DFL-200 default username

You can also use find your Router’s default guide on www.portforward.com.

Either of these will more likely than not help you find the login information you need.

Your network’s DHCP range

Most networks employ DHCP. Typically, your router doubles as your DHCP server. To

find your network’s DHCP range, you will need to log into your router (or other DHCP

server) and find the page containing those settings. If you cannot find these settings,

contact your network administrator or internet service provider.

Your network’s subnet Mask

A subnet mask (this is a VERY short simplification) is used to “subdivide” your network

into segments. You should be able to find your network’s subnet mask in the settings

you saw earlier when you ran “ipconfig /all” from a command prompt. You can also find

these under Control Panel ÆNetwork Connections ÆLocal Area Connection (or your

network adapter’s name) ÆProperties ÆInternet Protocol (TCP/IP) Properties.

The IP Address you will give your AP-9060/AP-16CO

You should first log into your router (or other DHCP server) and determine your DHCP

range. You need to pick a valid static IP address that is outside your DHCP range. You

should also (as a minimum) ping the IP address your have selected to make sure another

network device it not occupying it. On windows XP:

Start ÆAccessories ÆCommand Prompt ÆType:

ping [IP Address]

If you get a valid response, you should choose another address.

Page 9 of 18

Your AP-9060/AP-16CO’s password

You will need the administrative password for your AP-9060/AP-16CO so that you can

log into it and make changes. Your default user password is 111111. If your defaults

have been changed, you will need to get this information from within your organization.

Existing port forward / NAT information

You need know your existing port forward and/or NAT settings before adding new ones

in order to avoid conflicts. If you use point of sales software on your network you

should call your vendor and make CERTAIN you have the settings and know how

to avoid creating conflicts with them. Failing to do so could threaten your ability to

create new transactions for a significant period of time.

Pitfalls to Avoid

IP Addresses in Your DHCP Range

DHCP servers are used for giving out temporary IP addresses to devices on your network

that need them. This means that the IP address of any DHCP on your network can and

will change as these IP address leases expire.

Your DHCP server will have a range of IP addresses that it can use for this purpose. If

you set your AP-9060/AP-16CO’s static IP address to be within this range, you are

creating the possibility that another device will be will be given the same IP address by

your DHCP server. Should this occur, both of your devices will cease to function on

your network until the problem is resolved.

A best practice is to set the static IP address of your AP-9060/AP-16CO to be outside of

your DHCP server range, avoiding the possibility of this type of conflict. For example, if

your DHCP server’s IP address range was 192.168.1.100 – 192.168.1.200, good IP

addresses for your AP-9060/AP-16CO would be 192.168.1.50 or 192.168.1.250, but not

192.168.1.105.

Dynamic IP Addresses

If you leave your AP-9060/AP-16CO set to acquire a dynamic IP address, its IP address

is likely to change over time, nullifying the effects of any forwarded ports or NAT routes

to your AP-9060/AP-16CO and breaking access to it from the internet. If this occurs,

you will have to re-configure your router to pass the correct ports to it again.

A best practice is to use static IP addresses that are outside your DHCP range for all AP-

9060/AP-16COs that will have ports forwarded to them.

Using Dynamic Public IP Addresses without Dynamic DNS

If your Internet Service Provider has given you a dynamic IP address with your internet

connection, it is best, if possible, to acquire a static IP address from them. This way, you

can browse to your AP-9060/AP-16CO on the internet by simply using your public IP

address. For example, if your public IP address (from your information gathering

Page 10 of 18

checklist) is 96.226.2.104, you would simply open Internet Explorer and enter http://

96.226.2.104/ in your address bar to view your AP-9060/AP-16CO.

If you cannot acquire a static IP address, there are two possibilities. First, if your public

IP address changes and you can no longer view your AP-9060/AP-16CO, simply browse

to www.whatismyip.com from within your network to see your new public IP address,

and use that one until it changes again (usually several months).

If you do not like this option, you can use a dynamic DNS service. This way, you can

browse to a name, rather than address, such as http://mydvr.mydomain.com. There are

several of these services that offer free accounts. We prefer www.dyndns.org, and

wholeheartedly recommend them. Their setup is easy and free, and they offer software

that prevents your free account from expiring if your public IP address does not change

often enough. Please visit their site for more information.

Configuration

Configuring your AP-9060/AP-16CO

User Accounts

First and foremost, if you are exposing your DVR to the internet, as a best practice

you should change your default password to protect yourself from malicious

individuals.

You should change your password every 90 days.

Network Settings

Before beginning this section, please make sure your AP-9060/AP-16CO is connected to

your network.

By now you should have determined the following settings to your AP-9060/AP-16CO.

IP Address

Subnet Mask

Default Gateway (or just Gateway)

Go to the DVR, press the stop button to stop recording, and press the “Menu” button.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ApexCCTV Registratore digitale

ApexCCTV

ApexCCTV AP-7216 Manuale utente

Manuali Registratore digitale popolari di altre marche

FLIR

FLIR M3100E Series Manuale utente

VTRACKPRO

VTRACKPRO FPRO300 Manuale utente

Swann

Swann NVR-7085 models Manuale utente

XtendLan

XtendLan DVR-1670C Manuale utente

urmet domus

urmet domus 1093/004AHD Manuale utente

Holux

Holux M1 Manuale utente

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuale utente

Whistler

Whistler D16VRS Manuale utente

Defender Security

Defender Security 82-20235 Manuale utente

MISUMI

MISUMI MP-WF100M Manuale utente

Speco

Speco D8HU Manuale utente

UST

UST DDR-E04AA Istruzioni per l’uso

Consolidated

Consolidated Digital Video Recorder Manuale utente

Mace

Mace DVR0404RW Guida rapida

RCA

RCA RTD315W Manuale utente

FSM

FSM Colibri Grande PRO Manuale utente

Hauppauge

Hauppauge HD PVR 2 Manuale utente

Identivision

Identivision ICR-PH161i PIONEER Manuale utente