APG Ice Genie Manuale utente
Step 2: Fill water into the channel at the top
of the Outer Chamber. Fill until water reaches
just above the top row of cubes.
*Be careful not to put water directly into the
Inner Chamber.
Note: Pour out any water that overflows into
the upper part of the channel.
USING THE ICE GENIE™ICE CUBE MAKER
Step 1: Insert the Inner Chamber into the bottom of
the Outer Chamber, creating a seal. Feel around the
base of the Outer Chamber to see if the Inner
Chamber is properly seated.
Note: If base is not flat with bottom of Outer
Chamber, water will leak into the Inner Chamber.
Tip: Make sure it “pops” into place!
IMPORTANT SAFETY INSTRUCTIONS:
• Only use Ice Genie™ Ice Cube Maker as described in this manual
• Always store in a clean and dry place when not in use
• Ice Genie™ Ice Cube Maker is top rack dishwasher safe
• Keep away from extreme heat
• Ice Genie™ Ice Cube Maker is NOT microwave safe
For more tips and instructional videos, visit: www.IceGenieTips.com
INSTRUCTION MANUAL
COMPONENTS
Step 1 Step 2 Step 3
Step 3: Snap the Lid onto the Ice
Genie™ Ice Cube Maker.
Place into freezer upright until all
the water is frozen. (4-6 hours)
Inner Chamber Outer Chamber Lid
Fill to
this point
Middle
Area
Channel
IM5
©2018 APG. All Rights Reserved. | Patents Pending | Ice Genie is a trademark of APG.
ADDITIONAL BATCHES OF ICE
Users may find it easier to place a
standard sized can directly under
the Chamber. Push down on the
edge of the Chamber, causing the
Cylinder to move upwards away
from the Chamber.
Alternative Method
Step 4: Once frozen, remove Ice Genie™
Ice Cube Maker from the freezer, remove
the Lid, then firmly squeeze the Outer
Chamber from all sides.
Step 4
Step 5: Remove any loose ice that
has formed on the upper part of
the channel. Twist the Inner
Chamber left/right until it is free.
Then pull upward to remove it from
the Outer Chamber.
Tip:
If the Inner Chamber is
difficult to remove, wait 30
seconds and repeat step 4/5.
Step 5
Step 6: Once Inner Chamber is
removed, squeeze the Outer
Chamber, releasing all the ice
cubes into the middle area. Make
sure all of the ice cubes are
pushed out of the cavities prior
to reinserting the sleeve.
Note: Any remaining ice might
affect the efficiency of the sleeve
to keep water from leaking into
the center.
Step 6
Step 2: After the Inner
Chamber is fully in place,
simply refill the channels,
leaving the already made
cubes in the middle area
of the Ice Genie™ Ice
Cube Maker.
Once the Outer Chamber
is fully filled, repeat steps
3-6.
Ice Genie™ Ice Cube
Maker can store up to
three batches of ice. (120
cubes!)
Ice Genie™ Ice Cube Maker
can be hand washed with
warm soapy water or placed
in the top rack of a
dishwasher.
Step 2 CLEANING
Step 1 Alternative Method An alternative method
youmay find more
convenient,isto move
the cubes out of the way
by twistingthe Inner
Chamber back and forth
as youwork your way
around the ice cubes.
Note:Feel around the
base of the Outer
Chamber to see if the
Inner Chamber is properly
popped into place.
Step 1:Remove the ice
cubes from the unit and
place them into a
separate bowl. Next,
insert the Inner Chamber
back into the Outer
Chamber, then place the
ice cubes back into the
middle area of the Ice
Genie™ Ice Cube Maker.
Note:Users may find that
after emptying the ice
cubes, rinsing out the
chamber with water might
dispose of any unwanted
ice left over.
Altri manuali APG Macchina per il ghiaccio
