Aquatica Digital Olivia Manuale utente

www.aquaticabath.com

E: [email protected]

Olivia™

Corner acrylic bathtub

Installation & Care Manual

USA and CANADA

www.aquaticabath.com

E: [email protected]

P-Trap

(not supplied)

Olivia™

Corner acrylic bathtub

Aquatica®Freestanding

Bath Installer™

(not supplied)

1½” ﬂanged brass

tube for Aquatica®

cable-drive and

concealed bath

wastes.

PLEASE NOTE: Parts marked with are supplied as part of Aquatica®Freestanding Bath Installer™ Kit (NOT included with bathtub)

57.5”

55.0”

30.0”

55.0”

30.0”

41.75”

22.5”

26.75”

20.0”

16.5”

SIDE ELEVATION

Use “1 1/2” PVC or ABS Female Adapter

(use of PVC or ABS depends on your local or state

plumbing codes) Hub x FIPT

he ABS or PVC female adapter features a hub x female NPT thread

connection and provides a means for adapting a solvent weld

connection to a threaded connection.

Home Depot PART

1 1/2” ABS

Female Adapter

Hub x FIPT

3Fully tile the bathroom ﬂoor and walls behind the bathtub

Olivia™

Corner acrylic bathtub

6 & 7

1Choose appropriate area for bathtub installation

Drill bolts through side lip into

fully ﬁnished bathroom wall

ii) Silicone seal around the top edges

2Complete ﬂoor plumbing & water supply lines for faucets

i) Use Aquatica®Installation Kit

ii) Check Page x for detailed instructions

on how to use the Aquatica Installation kit

Attach the Side Panel

i) Leave 0.5” space between bottom of side panel and bathroom ﬂoor.

ii) Fit the top of the panel between ﬁtting and base frame.

iii) Secure in place with ﬁtting bolts.

4Place tub in position

TYPICAL FREESTANDING BATHTUB INSTALLATION PROCEDURE

Before you start:

• Ensure that the floor is even.

• The waste-overflow fitting is supplied with the product, however other accessories like the slip joint and

adaptors are not included and must be purchased separately.

• Because of the technical features of the product, it should be used only with the supplied waste-overflow

or specific 3rd party models that have been tested and approved by us.

• Place the bathtub by raising it up 4” with 4x4 pieces of lumber so you can have access from the bottom

of the bathtub.

• The bath must rest on its feet, not the monobloc sides. The feet must be adjusted to compensate for any

floor imperfections and leave minimal gap with floor.

INSTALLATION SEQUENCE

• The Olivia™ bathtub is equipped with factory pre-installed overflow system.

• The waste pipe/p-trap connection must be made directly to the waste/drain outlet located at the bottom of the tub.

• Picture 1-2: the bathtub is leveled via a water level at the intended local installation area.

• Picture 3: place the bathtub by raising it up 4” with 4x4 pieces of lumber so you can have access from the bottom of

the bathtub. Important note: during the installation, the bathtub should not be turned on its side to prevent its weight

from deflecting its monobloc sides. This is why it is important to use supports to raise the bathtub above the floor.

This will also provide you with easy access to the internal plumbing parts.

1 2 3

Olivia™

Corner acrylic bathtub

www.aquaticabath.com

E: [email protected]

1½” ABS DWV Hub

x FIPT Female Adapter*

INSTALLATION SEQUENCE continued

• Picture 4: the water outlet pipe should be connected.

• Picture 5: foot leveling lock nuts are adjusted.

• Picture 6: silicone is applied to the feet of the bathtub that stands on the floor.

• Picture 7: when the installation is completed, the bathtub is taken down from the supports ( ie 2 x 4x4's).

If necessary, installation is completed by applying silicone at several points between the bottom panel and floor.

Compatible adaptors for adapting a threaded male connection to a solvent weld connection:

• Mueller Industries: Part # 05913

• Nibco: C4803

http://www.homedepot.com/p/NIBCO-1-1-2-in-PVC-DWV-Hub-x-FIPT-Female-Adapter-C4803HD112/100677994

The adaptor must have the appropriate thread type or it will keep slipping and you will not be able to

get a tight connection!

Olivia™

Corner acrylic bathtub

Aquatica®

Freestanding Bath Installer™

(Kit available separately - not included with bathtub)

48mm

238mm

52mm

32mm

103mm

159mm

39mm

38mm

203mm

38mm

1 ½ " brass tube for female threaded

stone bath wastes.

1 ½ " ﬂanged brass tube for Aquatica®

cable-drive and concealed bath wastes.

38mm

203mm

38mm

1 ½ " brass tube for female threaded

stone bath wastes.

1 ½ " ﬂanged brass tube for Aquatica®

cable-drive and concealed bath wastes.

FEATURES

• 18 Gauge Epoxy coated Metal Deck Flange

• Designed to be installed in an 8” joist space

• Can be installed with Waterproofing Membrane

(*bronte™ NobleSeal TS Recommended)

• CSA Certified for Canadian and US markets

KIT INCLUDES

• 2 Brass Tailpieces (Fine Thread and Flanged)

• Freestanding Bath Installer™ assembly with 1-1/2” DWV ABS tailpiece

• Cutting template

INSTALLATION TIPS

• Use 6.5” hole saw to cut sub floor (not included).

Cutting template included

• Do not cut the brass Tailpiece as this may cause a leak

• Secure Deck Flange with 6 screws (not included)

Male Adapter Spg x MIPT - ABS DWV

for Aquatica®bath wastes with

Sch40 hub outlet.

Thread: 1 ½ NPSM (1 ½ IPS)

www.aquaticabath.com

E: [email protected]

INSTALLATION INSTRUCTIONS

Attaches to Freestanding Bath W/O

A. Cut 6-1/2” (16.5 cm) hole into wood sub-floor

(use supplied Cutout Template).

B. Measure and cut ABS Tailpiece as necessary

to ensure a secure connection to P-Trap below.

C. Insert Freestanding Bath Installer™ assembly into floor

opening and connect to Pipe below.

D. Affix to sub-floor with 6 screws (not supplied)

A. Install flooring surface, leaving a 6-1/2” opening to

access Drain.

B. Affix the appropriate brass Tailpiece to the Waste &

Overflow. NOTE: DO NOT CUT THE BRASS TAILPIECE

AS THIS MAY CAUSE A LEAK.

Ensure the measurement between the base of the

Drain and P-Trap will accomodate the Tailpiece.

A. Cut out the Installation Label with a utility knife and

remove to expose the Drain.

B. Apply lubricant (supplied) to the Tailpiece.

C. Position the Tub and brass Tailpiece in-line with the Drain.

D. Carefully lower the tub with the installed brass Tailpiece

into the Red Collar in Drain assembly. Ensure Tailpiece is

fully engaged with Seal.

Aquatica®

Freestanding Bath Installer™

(Kit available separately - not included with bathtub)

IMPORTANT: Do not remove Installation Label until Step 3.

DO NOT CUT THE SUPPLIED BRASS TAILPIECE. Doing so may cause a leak.

Disassembling the drain or cutting the Tailpiece will void the warranty.

www.aquaticabath.com

E: [email protected]

Pind vajab puhastamist ja hooldust. Siledale pinnale ei kogune

mustus kergelt.

Kasuta pehmet kangast, pesuvahendit ja vett regulaarseks

hoolduseks. Puhasta kuiva kangaga.

Väldi abrasiive või lahusteid, mis võiks pinda kahjustada.

Mitte korrektes hoolduse käigus tekitatud vigastused

ei kuulu garantii alla.

EST

Hooldus juhend

LV/LT/RU/PL/EST/EN/DE/FR/IT

max. 60°C

PAA Ltd.,

Unijas street 12A, Riga, Latvia

EN 14516

CL1

CA-DA

PAA-BT-SILKS-19/2013

Maintenance Instructions

The smooth surface of your Aquatica®Acrylic

Bathtub accumulates hardly any dirt, and can be

maintained by simply cleaning with a soft cloth,

using a mild detergent in water, then wiping over

with a dry cloth.

Avoid using abrasive cleansers or solvents,

which will cause damage to the surface. Damage

caused by use of these products, or any other

inappropriate treatment, is not covered by our

guarantee.

Инструкция по уходу

Поверхность легко чистится. За счет

гладкости грязь к ней не прилипает. Для

регулярного ухода используйте мягкую

ткань, мыльный раствор и воду. После

чистки вытирайте поверхность сухой тканью,

которая хорошо впитывает влагу.

Не используйте губки с абразивной

поверхностью и агрессивные растворители,

которые могут повредить ванну.

Повреждения, возникшие вследствие

неправильного ухода, не покрываются

гарантией.

Installation & Entretien

Cette surface est facile à entretenir et à

nettoyer. Sa surface particulièrement lisse, ne

retiens que très peu la saleté. Un entretien

quotidien nécessite simplement l’utilisation

d’un chiffon doux, de l’eau et un peu de savon.

Essuyer avec un chiffon sec. L’utilisation de

détergents ou de solvants endommageraient

cette surface. Les dommages resultants d’un

traitement non conforme effectué par l’utilisateur

sont exclus de la garantie que nous offrons.

Manuale per il corretto mantenimento

La superficie necessita di pulizia ed accorgimenti

per il corretto mantenimento. Una superficie

liscia non accumula lo sporco. Usare una

spugnetta con del detergente non aggressivo

per una pulizia regolare. Asciugare con un

panno. Evitare l’uso di solventi o materiali

abrasivi: potrebbero rovinare la superficie.

Un danno causato da trattamento inappropriato

non verra’ coperto dalla garanzia.

Instrucciones para la correcta manutención

La superficie debe de ser limpiada y

adecuadamente mantenida. Una superficie lisa

no acumula suciedad.

Utilice una esponja con un detergente suave

para la limpieza diaria. Seque con un paño.

No utilice disolventes o materiales abrasivos ya

que podrían dañar la superficie.

Los daños causados por el tratamiento

inadecuado no serán cubiertos por la garantía.

Olivia™- Maintenance Instructions

Olivia™- Инструкция по уходу

Olivia™- Installation & Entretien

Olivia™- Manuale per il corretto mantenimento

Olivia™- Instrucciones para la correcta manutención

Indice

Altri manuali Aquatica Digital Vasca

Aquatica Digital

Aquatica Digital Arabella Aquastone Bathtub Manuale utente

Aquatica Digital

Aquatica Digital PureScape 028 Series Manuale utente

Aquatica Digital

Aquatica Digital Relax Pro Manuale utente

Aquatica Digital

Aquatica Digital Relax Series Manuale utente

Aquatica Digital

Aquatica Digital AquaStone Purescape 748 Manuale utente

Aquatica Digital

Aquatica Digital Baby Boomer Manuale utente

Aquatica Digital

Aquatica Digital Spoon2 Purescape 204AM Manuale utente

Aquatica Digital

Aquatica Digital Purescape 748 Manuale utente

Aquatica Digital

Aquatica Digital Corelia Manuale utente

Aquatica Digital

Aquatica Digital PureScape 171 Mini Manuale utente

Aquatica Digital

Aquatica Digital EcoMarmor Istruzioni originali

Aquatica Digital

Aquatica Digital AquateX Corelia Manuale utente

Aquatica Digital

Aquatica Digital AquateX Lullaby Manuale utente

Aquatica Digital

Aquatica Digital Sensuality Mini AquateX Manuale utente

Aquatica Digital

Aquatica Digital Purescape 118L Istruzioni operative e di manutenzione

Aquatica Digital

Aquatica Digital AquateX Lillian Guida alla configurazione

Aquatica Digital

Aquatica Digital PureScape 308 Series Manuale utente

Aquatica Digital

Aquatica Digital Illusion AquateX Manuale utente

Aquatica Digital

Aquatica Digital AquateX Purescape 720 Manuale utente

Aquatica Digital

Aquatica Digital Aquastone Purescape 748 Manuale utente

Aquatica Digital

Aquatica Digital True Ofuro Tranquility Series Manuale utente

Aquatica Digital

Aquatica Digital Lullaby Mini Manuale utente

Aquatica Digital

Aquatica Digital Sensuality Aquastone Manuale utente

Aquatica Digital

Aquatica Digital Tulip Manuale utente

Manuali Vasca popolari di altre marche

Agua

Agua BARTOLI-66 Manuale utente

PAA

PAA PRELUDE Manuale utente

BETTE

BETTE SILHOUETTE Manuale utente

Kohler

Kohler K-820-GC Guida rapida

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Manuale utente

Oliveri

Oliveri Naples Manuale utente

Lyons

Lyons Elite ETLxx663219 Series Manuale utente

Woodbridge

Woodbridge BJ500 Istruzioni per il montaggio

Whirlpool

Whirlpool Ariel ARL-702 Manuale utente

TEIKO

TEIKO EXCELLENT DUO Manuale utente

American Standard

American Standard Colony 5-1/2' x 32" Manuale utente

American Standard

American Standard 3052OD.X0X Guida rapida

Kohler

Kohler K-1111-H2 Guida rapida

agape

agape MARSIGLIA AVAS1075 Manuale utente

Kohler

Kohler K-1151 Istruzioni per il montaggio

Kohler

Kohler K-1158 Guida rapida

Kohler

Kohler K-1244 Istruzioni per il montaggio

Kallista

Kallista P50045-G5 Istruzioni per il montaggio