Archos Drone VR Manuale utente
User Manual
Manuel d’utilisation - Benutzerhandbuch - Manual
de usuario - Manuale utente - Instrukcja obsługi -
Használati utasítás
2
Safety Notice for Battery
Please read the user handbook carefully and then keep it in a safe
place for future reference and maintenance.
- Only use the provided charger.
- When you install the battery, you must follow the electrode
instructions. It is not allowed to reverse the batteries, which can
cause short circuits.
- Non-rechargeable battery can’t be used, and the rechargeable battery
can only be charged under adult supervision.
- Different types of batteries (new and old) can’t be mixed
- Please contact your environmental government bureau to know how
to dispose and recycle Lipo batteries
- Please don’t overcharge the battery or leave the battery charging
alone.
- Don’t throw the battery into fire or put it in a high temperature
location, this may cause battery explosion
- The charger and battery are not toys.
- This product contains electronic components. Under water immersion
and humid environments are forbidden.
- Use dry cloth to wipe the surface
- Check the product regularly to see if there is any damage to the
components, if so please stop using until it has been repaired.
Do not put the battery in high temperature place, such as in the fire or
on a heating device to avoid damage or explosion.
Do not slam the battery on a hard surface.
Do not put the battery in water and keep it in dry place.
Do not open the battery.
Do not leave the battery without supervision when charging.
Make sure that there is no short circuit of the power wire.
Please use the recommended charger only.
Check the charger’s wire, plug, surface regularly. Do not
use any broken charger.
If you do not fly the drone at least once a week, maintain the
drone battery with about 50% power to keep its performance.
3
Charging Instructions for the Battery
1. Connect the drone battery with USB cable first then
choose one of the methods as on the picture below
to connect with USB plug.
2. The red USB indicator light is on when charging and
the light turns green when fully charged( The switch
must be powered off when charging).
* For faster charging, it is recommended to use an adapter
with 5V 2A output current (not included) to charge the battery
Phone charger
Power bank
Computer
charging
Car charger
Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with
household trash. Please contact local environmental or waste
agency or the supplier of your model or your nearest Li-Po
battery recycling center.
Drone battery
4
Check List Before Your Flight
1. Make sure the drone’s battery and transmitter’s
battery are fully charged.
2. Make sure the left lever of the transmitter is in the
middle position.
3. Please strictly follow the instructions to turn on and
turn off before operation. Turn on the transmitter
power first and then turn on the drone power before
flying; turn off the drone power first and then turn off
the transmitter power when you are finishing flying.
Improper turn on and turn off order may cause the
drone to lose control and threaten people’s safety.
Please make sure you correctly turn on and turn off.
4. Make sure the connection is strong between battery
and motor etc. The ongoing vibration may cause bad
connection of power terminal and make the drone
lose control.
5. Improper use may cause drone to crash, which may
lead to motor defects and noise, and then affect the
flying status or even stop flying. Please go to the
local distributor to buy new replacement parts in
case of damage.
5
Instructions for Drone and Transmitter
Drone
Front
Drone Cover
Housing
Rear
Left Right
Front LED
Propeller B
Propeller A
Propeller A
Battery holder
Propeller B
ON/OFF
Camera
Micro-SD card
slot
Front LED
Rear LED Rear LED
6
Transmitter
Heading Hold Mode
Right lever
(Forward/Backward)
Power Switch
Take O/Landing/
Emergency Stop
Button
Left lever
(Throttle / Rudder)
Phone holder
Battery compartment
High / Medium/Low
Speed button Trimmer mode button
7
Left lever Move the lever forward / backward / left / right to
y the drone up / down / turn left / turn right.
Right lever Move the lever forward / backward / left / right to
y the drone forward / backward / left / right.
Power Switch Push up the power switch to turn on the
transmitter, and pull
down to turn o.
Heading Hold
Mode
Press the button to enter heading hold mode,
and press again to
exit from heading hold mode.
High / Medium/
Low Speed Mode
Press down the Left lever to switch to High /
Medium/ Low Speed
Take O / Landing /
Emergency Stop
Button
Press the button and the drone will y up
automatically. Press the button again and the
drone will land on the ground automatically.
Press and hold the button more than 1s,
the drone propellers will stop and fall down
immediately.
Trimmer mode
Button
Press down this button, move the right lever to
the required trimmer direction, then it will adjust
the direction accordingly, when loose the lever,
then ESC from the trimmer mode.
8
Unfold the drone
Pull out the arm bracket as per the below arrow shows
(picture 1) , it will make a click sound, then it means
fully opened(picture 2). On the contrary, then it’s
folded.
Pull out the arm bracket as per the below arrow shows
(picture 3) , it will make a click sound, then it means
fully opened(picture 4). On the contrary, then it’s
folded.
Notice: Improperly operation may cause damage to the
bracket part.
9
VR Glasses
Headband
Upper phone
holder
Lower phone
holder
Lens
Phone holder slot
Left lens Right lens
PU Foam
10
Installing the batteries:
Open the battery cover on the back side of the
transmitter and put 4 alkaline batteries (AAA, not
included) into the box in accordance with electrode
instructions, as picture shown.
Pre-ight Operation Instructions
Frequency Pairing
1. Turn on the transmitter switch (Picture 1) and the
power indicator light flashes rapidly. Push the Left
lever all the way down to the lowest position and
then release. The Left lever moves back to the middle
position automatically. (Picture 2 / 3) The power
indicator light flashes slowly, indicating the transmitter
is ready for frequency pairing.
Battery cover
4X1.5V
Alkaline Batteries
Notice:
1. Make sure the electrodes match.
2. Do not mix new with old batteries.
3. Do not mix dierent kinds of batteries.
4. Do not charge non rechargeable batteries.
Indice
Lingue:
