Arctiko LRE 700 Guida rapida
LRE 700/1400 & LFE 700/1400
IQ/OQ - INSTALLATION AND
OPERATIONAL QUALIFICATION
1/17 5084132-03
Introduction
The objective of this Installation and Operational Qualification (IQ/OQ)document is to qualify
the installation and operation of Arctiko appliances.
The Installation and Operational Qualification document definesthe minimum test procedures
and acceptance criteria to be used to establish that the Arctiko appliance is installed and op-
erated according to our specifications.
The Installation Qualification is intended to verify that the appliance is delivered in corre-
spondence with the ordered appliance and is installed in a correct environment.
The Operational Qualification is intended to verify the function of the appliance and its readi-
ness for operation.
Please be aware that local IQ/OQ procedures can require additional control and verification
during the validation.
If any documentation, which were not supplied with the appliance, should be needed for the
present qualification, such can be downloaded from the service website of Arctiko. Please con-
tact the distributor of the Arctiko appliance to obtain the documentation in question.
2/17 5084132-03
Index
1Basic information ......................................................................................................................3
1.1 Signature and device list................................................................................................................. 4
2Installation Qualification ..........................................................................................................5
2.1 Documentation verification ............................................................................................................5
2.2 Appliance check points................................................................................................................... 5
2.3 Environmental verification .............................................................................................................. 7
3Operational Qualification.........................................................................................................8
3.1 Parameter verification and adjustment....................................................................................... 8
3.2 Placement of test probes................................................................................................................9
3.3 Temperature mapping .....................................................................................................................11
3.4 Alarm and temperature recovery verification..........................................................................13
3.5 Deviations to criteria of acceptance (Deviation report)........................................................16
4Result of Installation and Operational Qualification.......................................................... 17
3/17 5084132-03
1Basic information
Model: _________________________
Serial number: _________________________
Date of qualification (DD/MM/YYYY):_________________________
Qualification carried out by (name):_________________________
Customer: _________________________
Location of the appliance:_________________________
_________________________
_________________________
COMMENTS
4/17 5084132-03
1.1 Signature and device list
Each person, who participates in the present IQ/OQ qualification, shall fill out the signature
list below in order to establish traceability to the test signatures.
All devices used for the execution of the current IQ/OQ shall be noted in below device list.
SIGNATURE LIST
NAME (CAPITAL LETTERS)
JOB TITLE
DATE AND SIGNATURE
DEVICE LIST
DESCRIPTION
BRAND
MODEL
DATE OF
CALIBRATION
5/17 5084132-03
¨
2Installation Qualification
The Installation Qualification is intended to verify that the appliance is delivered in corre-
spondence with the ordered appliance and is installed in a correct environment.
The IQ is concluded if all acceptance criteria are fulfilled. If any deviations are found during
the qualification, such must be corrected and thereafter approved.
2.1 Documentation verification
Check and verify the following points:
DOCUMENTATION
CHECK (
√
)
COMMENTS
Ensure operating instruction manual has been supplied with
the appliance
Ensure operating instruction manual has been read and un-
derstood by the user(s)
2.2 Appliance check points
Check and verify the following points:
SCOPE OF SUPPLY
CHECK (
√
)
COMMENTS
Delivery
E
nsure that
the appliance complies with the
ordered appliance as well as containing op-
tional accessories (if any) as stated in the
purchase order of the customer
Power supply
Ensure the power supply
of the appliance
complies with the purchase order of the cus-
tomer (check the rating plate of the appli-
ance)
6/17 5084132-03
APPLIANCE
CHECK POINTS
CHECK (
√
)
COMMENTS
Packaging &
protection mate-
rial
Ensure a
ll packing material has been re-
moved
Ensure a
ll protection foi
l has been removed
from the cabinet and display
Cabinet
Ensure n
o scratches on exterior cabinet
Ensure n
o scratches on interior cabinet
Ensure n
o cracks on plastic frames
Door
Ensure the door c
an open and close
Ensure the door c
an be lock
ed using
the key
Ensure n
o gap between gasket and frame
Ensure n
o scratches
Castors
Ensure that the c
astors are locked (if
equipped with castors)
Feet
Ensure that the f
eet are levelled (if equipped
with levelling feet)
Controller
Ensure n
o
scratches on
the
display
Ensure that a
ll cables
are
mounted
according
to safety requirements
Remote alarm
connection
Ensure that t
he remote alarm contact is cor-
rectly connected to an external system (utili-
zation of the remote alarm contact is option-
al)
Compressor
Ensure n
o unusual noise
Fan
Ensure n
o unusual noise
Electrical con-
nection
Ensure that the power cord is correctly
mounted on the appliance
Ensure that the electrical connection is
per-
formed in accordance with:
a) power supply noted on the rating
plate of the appliance
b) power supply of the power socket
c) operating instruction manual
d) local regulations
a)
b)
c)
d)
Ensure that the
power supply fuse of the
switchboard is 10A
Cleaning
Ensure that t
he appliance has been cleaned
7/17 5084132-03
2.3 Environmental verification
Check and verify the following points:
ENVIRONMENT
CHECK (
√
)
COMMENTS
Ambient condi-
tions
Ensure
by using a thermometer
a m
aximum
ambient temperature of:
+25°C (freezer models)
+43°C (refrigerator models)
Ensure n
o direct sunlight on the
appliance
Ensure that the appliance is not
located near
heat sources
Ensure that t
he room is well ventilated
Surface
Ensure installation
on a
solid
and
flat surface
to avoid vibrations and unintentional noise
Air
circulation
Ensure
free spac
e
around the appliance
to
ensure the required air circulation according
to the operating instructions manual
CHECKED/TESTED BY
DATE
SIGNATURE
VERIFIED BY
DATE
SIGNATURE
8/17 5084132-03
3Operational Qualification
The Operational Qualification is intended to verify the function of the appliance and its readi-
ness for operation.
The OQ is concluded if all acceptance criteria are fulfilled. If any deviations are found during
the qualification, such must be corrected and thereafter approved.
Check and verify the following parameters and fill out the below table. We recommend that the
parameters are checked app. once a year.
3.1 Parameter verification and adjustment
DESCRIPTION
DEFAULT
SETTINGS
LRE 700
LRE 1400
D
EFAULT
SETTINGS
LFE 700
LFE 1400
CHECK/ADJUST THE
SET VALUE AND
NOTE THE VALUE
COMMENTS
Password
(PS)*22 22
Set point
(St) +4 -20
Control delta /
hysteresis (rd) 2 2
Interval between
defrost (dl) N/A 6 hrs.
High tempera-
ture alarm by-
pass time after
defrost and door
open (d8)
0 0
Alarm bypass
after door open
(d8d)
2min. 2 min.
Low
temp. alarm
(AL)**4 10
High
temp. alarm
(AH)**5 8
Low and high
alarm delay (Ad) 5 min. 5 min.
*Use of password 22 will access all parameters. Password 0, which is stated in the user manual, will only
access a selected number of parameters.
**AL and AH are relative thresholds to the set point. The set values must be positive values.
Examples
Set point: +4°C
High. temp. alarm (AH): 5
AH alarm activation: +9°C
Set point: +4°C
Low. temp. alarm (AL): 3
AL alarm activation: +1°C
Set point: -20°C
High. temp. alarm (AH): 7
AH alarm activation: -13°C
Set point: -20°C
Low. temp. alarm (AL): 6
AL alarm activation: -26°C
9/17 5084132-03
3.2 Placement of test probes
Prepare the appliance for the Operational Qualification by mounting test probes.Place the test
probes inside the appliance as described in below table and as shown in below illustration (see
the red arrows).
Each test probe must be loaded with a 25 gr. brass block
(or equivalent) to ensure precise temperature measurement.
LRE/LFE 700
PROBE
LOCATION
Probe no. 1
45 c
m
distance
from the top of
the
interior cabinet
Probe no. 2
C
enter
of the
chamber
(72 cm distance from the top of
the
interior cabinet)
Probe no.
3
45 cm distance from the bottom of the interior cabinet
P
robe
no. 1
P
robe
no.
2
P
robe
no.
3
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Arctiko Congelatore
Arctiko
Arctiko Integraline ULUF P10 Manuale utente
Arctiko
Arctiko Integraline ULUF P390GG Manuale utente
Arctiko
Arctiko UPUL 580 Manuale utente
Arctiko
Arctiko ULUF P390 Manuale utente
Arctiko
Arctiko LCF 100 Manuale utente
Arctiko
Arctiko LTFE 140 Manuale utente
Arctiko
Arctiko SF SERIES Manuale utente
Arctiko
Arctiko ULUF Manuale utente
Arctiko
Arctiko CRYO 170-0 Manuale utente
Arctiko
Arctiko LTFE 310 Manuale utente
Arctiko
Arctiko ULTF 80 Manuale utente
Arctiko
Arctiko ULUF 120 Manuale utente
Arctiko
Arctiko SUF 100 Manuale utente
Arctiko
Arctiko CRYO 170-0 Manuale utente
Arctiko
Arctiko UPUL 580 Manuale utente
Arctiko
Arctiko CRYO 170 Manuale utente
Arctiko
Arctiko LTF 535 Manuale utente
Arctiko
Arctiko ULTF 80 Manuale utente
