Ares Crossfire Manuale
Owner’s Manual &
Technical Information (AU)
2
Specication
All-up weight: .......................560g
Weight without battery:.......390g
Size (motor diagonals):.......280mm
Length:.................................232mm
Width:...................................234mm
ESCs (x4):.............................12A continuous; 15A peak; ONE-SHOT enabled
Camera: ...............................Semi wide-angle lens
Video Transmitter: ...............25mW – 32 channels on 4 bands
Video antenna: ....................Protected cloverleaf, circular polarized
Flight time:...........................5–7 minutes
Propellers:............................6 x 4.5” (clockwise and counterclockwise rotation)
Battery: ................................3S 2200mAh 25C
3
In This Manual
Introduction ................................................................................ 4
Contents ..................................................................................... 4
Required to complete................................................................. 5
FCC Information ......................................................................... 5
Safety precautions ..................................................................... 5
LiPo battery warnings ................................................................ 6
Identication of components..................................................... 7
Set-up and Programming........................................................... 8
Flight Preparation.....................................................................22
VTX channel selection.............................................................. 24
Adjusting the camera angle.....................................................25
Recommended accessories....................................................25
Lawful Operation ......................................................................26
Replacement Parts ..................................................................26
Warranty. Service & Support ...................................................28
IMPORTANT! This radio control model is not a toy. It must be operated and
own according to these instructions and may cause serious injury to persons
or damage to property if not used responsibly or if operated without due
caution. Unsuitable for children under 14 years of age.
4
Introduction
The Ares Z-line Crossre Racing Quad is a high-performance quad that’s
ideal for getting started in 250 class racing. The Crossre provides natural
ight characteristics designed and tuned for FPV racing through a custom
ight controller that’s preloaded with the latest Cleanight software and
supports future updates via a micro USB port. The 32bit ight controller is
also customizable with multiple ight modes, including Acro (3-axis) and Self-
Leveling (6-axis) mode. Powerful and efcient brushless race motors provide
the Crossre’s speed and are complemented by 12amp ESCs with ONE-SHOT
enabled software.
A unique low-prole design and streamlined body combine to give the
Crossre improved aerodynamics and protection for the electronics against
the elements. The airframe is made from high-quality 3k twill weave matte
carbon ber for strength and lightweight performance. The Crossre comes
with a choice of two pre-painted, race-inspired stock canopies (red and blue)
with two alternate choices (green and orange) offered separately, allowing
you to race in your choice of colors. To top off the attractive design, bright
red LED tail lights help with visibility and make sure your competitors know
who’s in front of them on the course. As for a video system, the Crossre
comes with a pre-installed ultra-micro 25mW, 32-channel, 4-band VTX (video
transmitter) and a 640 x 480 camera with 120 degree FOV (eld-of-view) that
combine to provide a crisp FPV experience. The VTX is compatible with your
favorite goggles or a quality 5.8GHz video receiver / monitor, like the newly
released Ares Z-line monitors.
Perhaps best of all, the Ares Z-line Crossre arrives fully assembled out of the
box and includes pretty much all the components you need to race – even a
3S 2200mAh battery that’s easily removed without taking off the canopy. All
you need to add is your own standard-size (end pin) or satellite receiver and
you’ll be heading out to race your new Crossre before you know it.
Contents
1 x Factory assembled Crossre racer quad.
1 x 3S 11.1V 2200mAh LiPo battery.
1 x USB to micro USB cable.
4 x 6 x 4.5” (CW & CCW) propellers.
1 x Cloverleaf antenna.
1 x 8mm wrench for cloverleaf antenna.
1 x 1.5mm L-shape hex drive.
1 x Quick-start guide.
5
Required To Complete
1 x 6-channel (minimum) computer radio set.
1 x 6-channel (minimum) end pin receiver.
1 x Strip of self-adhesive hook and loop tape.
1 x Suitable 3S LiPo battery charger.
You will also need access to Cleanight open-source software in order to
congure your Crossre’s ight control board.
FCC Information
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including interference
that may cause undesired operation.
Caution: Changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This product contains a radio transmitter with wireless technology which
has been tested and found to be compliant with the applicable regulations
governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency
range.
The associated regulatory agencies of the following countries recognize the
noted certications for this product as authorized for sale and use: USA
Safety Precautions
Failure to use this product in the intended manner as described in the
following instructions can result in damage and / or personal injury. A Radio
Controlled (RC) quadcopter is not a toy! If misused it can cause serious bodily
harm and damage to property.
Keep items that could become entangled in the propellers away from the
propellers, including loose clothing, tools, etc. Be especially sure to keep your
hands, face and other parts of your body away from the propellers.
As the user of this product you are solely and wholly responsible for operating
it in a manner that does not endanger yourself and others or result in
damage to the product or the property of others.
This model is controlled by a radio signal that is subject to possible
interference from a variety of sources outside your control. This interference
can cause momentary loss of control so it’s advisable to always keep a safe
distance from objects and people in all directions around your model as this
will help to avoid collisions and/or injury.
6
• Never operate your model if the voltage of the batteries in the transmitter
is too low.
• Always operate your model in an open area away from obstacles, people,
vehicles,buildings, etc.
• Carefully follow the directions and warnings for this and any optional
support equipment (chargers, rechargeable batteries, etc.).
• Keep all chemicals, small parts and all electronic components out of the
reach of children.
• Moisture causes damage to electronic components. Avoid water exposure
to all electronic components, parts, etc. that are not specically designed
and protected for use in water.
LiPo Battery Warnings
IMPORTANT NOTE: Lithium Polymer batteries are signicantly more volatile
than the alkaline, NiCd or NiMH batteries also used in RC applications.
All instructions and warnings must be followed exactly to prevent property
damage and / or personal injury as the mishandling of LiPo batteries can
result in re. By handling, charging or using the included LiPo battery you
assume all risks associated with LiPo batteries. If you do not agree with these
conditions please return the complete product in new, unused condition to
the place of purchase immediately.
• You MUST charge the LiPo battery in a safe area away from ammable
materials.
• NEVER, at any time, leave the LiPo battery unattended when it’s being
charged.
• When charging the battery you should ALWAYS remain in constant
observation to monitor the charging process and react immediately to
any potential problems that may occur.
• After ying / discharging the battery you must allow it to cool to ambient/
room temperature before recharging.
• To charge the LiPo battery you MUST use only the included charger in the
transmitter. Failure to do so may result in a re causing property damage
and/or personal injury. DO NOT use a NiCd or NiMH charger.
If at any time during the charge or discharge process the battery begins to
balloon or swell, discontinue charging or discharging immediately. Quickly
and safely disconnect the battery, then place it in a safe, open area away
from ammable materials to observe for at least 15 minutes. Continuing to
charge or discharge a battery that has begun to balloon or swell can result in
a re. A battery that has ballooned or swollen, even a small amount, must be
removed from service completely.
For best results, store the battery at room temperature – approximately
68 – 77°Fahrenheit (F) – and in a dry area.
7
Identication of Parts
Clockwise motor
Counter-
clockwise
motor
Counter-clockwise
motor
Clockwise motor
Outrigger
support
Outrigger arm
Canopy mount
RP SMA
antenna mount
Spektrum
Satellite port
Video camera
Video Transmitter
Channel Selectors
Flight Control Board
Video
transmitter
USB port
Cloverleaf antenna
8
Set-Up & Programming
1. Remove the canopy. Withdraw the rear body clip and gently ease the
canopy from the airframe by gently unclipping the fairings from the
outrigger supports and sliding the canopy forward, over the camera.
2. Canopy protection. For transport the canopy is protected by a thin shrink
wrap lm covering. Remove this to appreciate the full color luster of your
Crossre’s paintwork.
3. Transmitter programming/preparation. Pair your chosen transmitter
and receiver by following the pairing/binding procedure noted in your
transmitter’s instruction manual. Having done this, ensure that:
• The model memory you’ve chosen for your Crossre is set to ACRO mode.
• The wing type is set to single servo aileron control.
• All trims are centered.
• End Point Adjustment (ATV) is set to 100% on all channels.
• All sub trims are centered.
4. Wiring identication. Locate the receiver wiring loom on the left-hand side
of the electronics board and note the location ID for each wire using the
guide below:
9
Hitec/Futaba
• Red/Black/White – Aileron CH1
• Red – Elevator/CH2
• White – Throttle/CH3
• Green – Rudder/CH4
• Blue – Auxiliary 1/CH5 (normal gyro/self level gyro)
• Yellow – Auxiliary 2/CH6 (lost model beeper)
Spektrum/JR
• Red/Black/White – Throttle/CH1
• Red – Aileron/CH2
• White – Elevator/CH3
• Green – Rudder/CH4
• Blue – Auxiliary 1/CH5 (normal gyro/self level gyro)
• Yellow – Auxiliary 2/CH6 (lost model beeper)
5. Reciever Connection. Plug the wires into the respective sockets on your
receiver noting that the single-pin connectors should be attached to the
‘signal’ pin, usually reserved for the yellow, orange or white wire.
6. Receiver installation. Secure your receiver to the upper frame using hook
and loop tape and secure the antenna wire(s). Note that only low-prole end
pin receivers are suitable for the Crossre due to the close proximity of the
fuselage shell when tted.
10
7. Antenna installation. Install the cloverleaf downlink antenna using the
8mm wrench. WARNING! The Crossre should NEVER be powered ON
without the antenna connected as this can damage the video transmitter
circuitry.
8. Download the Cleanight Congurator software. Before ying your
Crossre you’ll need to congure and tune the Flight Control Board using
Cleanight open-source software. This software can be sourced via
Google Chrome using the following method:
a. Open Google Chrome.
b. Enter ‘Apps’ by clicking the Apps icon in top left corner of your menu bar.
c. Click on the ‘Web Store’ icon.
d. Enter ‘Cleanight’ into the search box (top left corner).
e. Click the + TO CHROME icon to download the ‘Cleanight Congurator’ software.
f. When the software has been successfully downloaded the green CF icon will
appear in the Apps menu.
Important note: Due to the nature of open-source software the Cleanight
Congurator interface is susceptible to regular updates and may not mirror the
screen images provided in the step-by-step set-up stages detailed below.
Indice
Altri manuali Ares Quadricottero
