Arkon CLAMPRV29 Manuale utente
Telescoping pole extends upward from
17 inches to 29 inches.
Compatibility:
Fits smart phones with cases weighing
up to 2 pounds and measuring up to 4”
wide and 1/4”-20 compatible cameras.
IMPORTANT:
Do notovertightenring. Overtightening
ring may damage threads on holder
and also make it difficult to adjust
holder.
3
2
Attach mount to surface by tightening C-clamp knob. Slide optional
rubber clamp boot onto the top of the mount’s clamp to prevent
scratching clamp surface if desired.
For thicker tables or desks, adjust the clamp bracket by using a Phillips
screwdriver to remove the screws from the top position and move
them to the bottom position.
Your Pro Stand Clamp Mount will arrive in four parts:
Clamp Pedestal with
Telescoping Pole
Overhead Arm
Assembly
25mm to 1/4”-20
Camera Bolt Adapter
(optional)
RV001WR-B
Attach overhead arm assembly to clamp pedestal by unscrewing the
collar at the top of the pole until the metal ball side of the overhead
arm assembly fits into the collar. Tighten collar clockwise to secure.
Unscrew tightening ring from holder. Place ring over the 17mm end of
mount then snap the holder onto the ball. Set to desired position, then
tighten ring.
SP25MMCAM
Assembled Mount
SP3RMPR0PL
SP3RMPR0PL
HD011-B
Tightening Ring
Tightening
Knob
Collar
Metal
Ball Side
Screws
Screws
Continued on page 2
CLAMPRV29 |Arkon Pro Stand Clamp Mount for Phone or Cameras
HD011-B
Phone Holder
RV001WR-B
Clamp Bracket
C-Clamp Knob
C-Clamp
rev.091818
1a1b
7To attach optional camera, pico projector, or Mevo camera adapter,
unscrew shaft knob and remove phone holder, ring, and ball adapter.
Attach the 25mm ball end of the camera adapter to the shaft and
tighten clockwise to secure.
6Adjust the height of the pole by loosening the adjustment collar
counterclockwise. Tighten clockwise to set height.
5Shafts can be adjusted by unscrewing the shafts’ knobs to loosen.
Tighten knobs to set.
Consumer Hotline:
USA (800) 841-0884
INT’L (626) 254-9005
Monday - Friday 9 am - 5 pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in Taiwan and USA
© Copyright 2018 Arkon Resources, Inc.
Safety Precautions
Arkon Resources, Inc. is not responsible for any damages caused to your
device or yourself due to the installation or use of this mount.
!
page 2
4Using two hands, insert phone into the holder by pushing the device
into one of the spring-loaded support arms. Expand the other support
arm and fully insert device until it lays flat against the blue rubber pad.
CLAMPRV29 |Arkon Pro Stand Clamp Mount for Phone or Cameras rev.091818
Altri manuali Arkon Rack e supporto
Arkon
Arkon PTM129-SRVC Manuale utente
Arkon
Arkon CM395 Manuale utente
Arkon
Arkon MM323 Manuale utente
Arkon
Arkon RCBTABLED Manuale utente
Arkon
Arkon TTGO121 Manuale utente
Arkon
Arkon SM5-MV5003G3 Manuale utente
Arkon
Arkon SM427 Manuale utente
Arkon
Arkon MP070-7PS-1 Manuale utente
Arkon
Arkon CM925-S Manuale utente
Arkon
Arkon SM5-TY6009G3 Manuale utente
Arkon
Arkon BBP135 Manuale utente
Arkon
Arkon SLIM-GRIP SM427 Manuale utente
Arkon
Arkon BB212 Manuale utente
Arkon
Arkon SM236 Manuale utente
Arkon
Arkon CM012 Manuale utente
Arkon
Arkon DSLRTABMG5 Manuale utente
Arkon
Arkon VG917-L Manuale utente
Arkon
Arkon CM160 Manuale utente
Arkon
Arkon BB228 Manuale utente
Arkon
Arkon IPM123-G Manuale utente
