07/2021
Included in delivery:
a1 USB radio transceiver
aFlysck 2+
a2 standard AA rechargeable baeries
a1 USB -C baery charger (100-240 Volt, 50-60 Hz)
a1 wall mount
4red acve → charging
All control elements can be used simultaneously and may be
used to invoke an interacon which can be defined in the user
applicaon (e.g. drag objects while buon trigger pressed,
open a menu dialogue).
3red flash → low baery
The Flysck2+ is a wireless input device for all ART infrared
opcal tracking systems using passive markers inside two
detachable compartments protected by cone-shaped
enclosures. It offers a vibraon motor for inducing feedback
paerns and a beep funcon.
# 6 pressing the joysck
Control elements of the Flysck2+
Buon sequence:
1green flash → acve radio data transmission successful
Input transacons (buons
& joysck) are transmied
band (IEEE 802.15.4).
via wireless transmission
The Flysck2+ has a trigger, six buons and an analog joysck
with an addional buon funconality.
# 1 trigger
# 2 - # 5 colored buons, right to le
# 7 - # 8 grey buons, le to right
operang in the 2.4GHz
2yellow flash → inializing radio communicaon
Flysck2+ has two LEDs to signal ist state:
Addionally, the Flysck2+ offers one vibraon motor for
vibraonal feedback paerns and a beep funcon.
Quick-Guide Flysck2+
Safety advice:
aDo not use non-rechargable baeries.
aRemove baeries before shipping Flysck2+.
aUse delivered or rechargeable baeries NiMH 1,2V.
aInsert the rechargeable baeries into the baery
compartment in the indicated polarity.
RadioTransceiver
The RadioTransceiver3 is used for radio communicaon with
interacon devices such as Flysck2+.
Plug-in the Radio-
Transceiver3 to any free USB port of the controller, then press
F2 in order to search for new hardware. Configuraon is done
automacally. Range with line of sight is more than 7m but
can be reduced when the signal penetrates material, e.g.
projecon screens.
During operaon, do not unplug the USB radio transceiver!
For more informaon or in case you need to change sengs
manually please refer to the DTRACK3 User's Guide .
1
the baeries, take care of the polarities - also note the
imprinng '+ -' on the handle. Close the compartment aer
(approx. 5 h) the
inserng the baeries.
The baery compartment is at the lower end of the handle.
Remove the cover of the baery compartment. To insert
baeries may be
status LED: off).
Baeries + charging
Once the baery
pack is fully charged
The charging port is at the boom of the handle and has to
be connected with the supplied baery charger. As soon as
the charger is connected to Flysck2+ the charging process
is started (red status LED: connuously acve).
used again (red
3
4
Make sure that your Flysck2+ is listed under 'available
Flyscks' - validate the serial number listed here to the one
from your device.
Flysck2+ configuraon
Detach the upper marker compartment of the Flysck2+ to
gain access to the serial number. Now assign your Flysck2+
to a Flysck ID:
Open 'Tracking'→'Flysck' to manage the number of Flyscks
(max. 20) and to configure the corresponding sengs to be
used. Increase the number of Flyscks by 1 or use the numeric
up down buon. The corresponding entries in the list of
selected Flyscks will show up.
5
Wall mount
which can be used as desk stand
for Flysck or wall mount. It can
It can also be used to charge the Flysck when not used.
be assembled as shown in picture.
Flysck2+ comes with a mount
2
