Artisan ARTP-PB Guida

PASTE SERIAL NUMBER

LABEL IN THIS LOCATION

NOTES:

POWER BURNER SERIAL NUMBER LABEL:

CALIFORNIA PROPOSITION 65 - WARNING

The burning of gas cooking fuel generates toxic by-products, which are on the list of substances which

are known by the State of California to cause cancer or reproductive harm. California law requires

businesses to warn customers of potential exposure to such substances. To minimize exposure to

these substances, always operate this unit according to the use and care manual, ensuring you

provide good ventilation when cooking with gas. This warning is issued pursuant to California Health &

Safety Code Sec. 25249.6

GENERAL SAFETY PRECAUTIONS:

WARNING: If the information in this manual is not followed exactly, a fire or explosion may

result causing property damage, personal injury or death.

WARNING: Do not try lighting this appliance without reading the LIGHTING INSTRUCTIONS

section of this manual.

WARNING: For outdoor use only. This cooking appliance is not intended to be installed in or

on recreational vehicles and / or boats.

FOR YOUR SAFETY:

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity

of this or any other appliance.

• An LP cylinder not connected for use shall not be stored in the vicinity of this or

any other appliance.

WARNING

ELECTRICAL PARTS

AND COMPONENTS

DISCONNECT ALL POWER SUP-

PLIES AND BATTERIES BEFORE

SERVICING

WARNING

FLAMMABLE GAS

DISCONNECT ALL PROPANE OR

NATURAL GAS SUPPLIES TO THIS

UNIT BEFORE SERVICING

A division of Superior Equipment Solutions, Inc.

1085 Bixby Drive

City of Industry, CA. 91745

Ph.: (888) 383-8800

Fax: (323) 726-4700

Web: www.artisangrills.com

Artisan™3020914

!WARNING

1. DO NOT STORE OR USE GASOLINE OR OTHER FLAMMA-

BLE LIQUIDS OR VAPORS IN THE VICINITY OF THIS OR

ANY OTHER APPLIANCE.

2. AN LP CYLINDER NOT CONNECTED FOR USE SHALL NOT

BE STORED IN THE VICINITY OF THIS OR ANY OTHER

APPLIANCE.

!DANGER

IF YOU SMELL GAS:

1. SHUT OFF GAS TO THE APPLIANCE

2. EXTINGUISH ANY OPEN FLAME.

3. OPEN LID.

4. IF ODOR CONTINUES, KEEP AWAY FROM THE APPLI-

ANCE AND IMMEDIATELY CALL YOUR GAS SUPPLIER

AND OR FIRE DEPARTMENT.

!AVERTISSEMENT

1. NE PAS ENTREPOSER NI UTILISER DE L’ESSENCE NI

D’AUTRES VAPEURS OU LIQUIDES INFLAMMABLES DANS

LE VOISINAGE DE L’APPAREIL, NI DE TOUT AUTRE AP-

PAREIL.

2. UNE BOUTEILLE DE PROPANE QUI N’EST PAS RACCOR-

DÉE EN VUE DE SON UTILISATION. NE DOIT PAS ÉTRE

ENTREPOSÉE DANS LE VOISINAGE DE CET APPAREIL

OU DE TOUT AUTRE APPAREIL.

!DANGER

S’IL Y A UNE ODEUR DE GAZ:

1. COUPEZ L’ADMISSION DE GAZ DE ‘LAPPARIEL.

2. ÉITENDRE TOUTE FLAME NUE.

3. OUVRIR LE COURVERCLE.

4. SI L’ODEUR PERSISTE, ÉLOIGNEZ-VOUS DE L’APPAREIL

ET APPELEZ IMMÉDIATEMENT LE FOURNISSEUR DE GAZ

OU LE SERVICE D’INCENDIE.

F AVERTISSEMENT

PIÈCES ÉLECTRIQUES ET COMPO-

SANTS.

H AVERTISSEMENT

GAZ INFLAMMABLE

DÉBRANCHER TOUS LES GAZ PROPANE OU GAZ NATUREL

DE CET APPAREIL AVANT DE PROCÉDER À L'ENTRETIEN.

READ THIS CARE AND USE MANUAL CAREFULLY AND COMPLETELY BEFORE USING YOUR

POWER BURNER TO REDUCE THE RISK OF FIRE, BURN HAZARD OR OTHER INJURY. KEEP

THIS MANUAL FOR FUTURE REFERENCE.

When properly cared for, your ™ Power Burner will give safe, reliable service for many

years. However, extreme care must be used since the Power Burner produces intense heat, which can

increase accident potential. When using this appliance, basic safety practices must be followed, includ-

ing but not limited to the following:

• Begin by ensuring proper assembly. A qualified technician should perform all other service.

• Do not repair or replace any part of the Power Burner unless specifically recommended in this manu-

al.

• All other service should be referred to and performed by a qualified technician.

• For personal safety, wear proper apparel Loose fitting garments or sleeves should never be worn

while using this appliance Some synthetic fabrics are highly flammable and should not be worn while

cooking.

• Never let clothing, pot holders or other flammable materials come in contact with or too close to any

grate, burner or hot surface until it has cooled down sufficiently. Fabrics may ignite and result in per-

sonal injury.

• Use only dry potholders: moist or damp potholders on hot surfaces may cause personal burns from

steam. Do not use a towel or bulky cloth in place of potholders. Do not let potholders touch hot por-

tions of the Power Burner grate.

• Only certain types of glass, heatproof glass ceramic, earthenware, or other glazed utensils are suita-

ble for Burner use. These types of materials may break with sudden temperature changes. Use only

on low or medium heat settings and according to their manufacturer’s directions.

• Grease is flammable. Let hot grease cool before attempting to handle it.

• Avoid letting grease deposits collect in the bottom of the Power Burner by cleaning the grease tray

often. Never while the Power Burner is on or hot from recent use; pan will not come out.

• Do not use aluminum foil to line the Power Burner grates, nor to line the drip tray. This can severely

upset combustion airflow or trap excessive heat in the control area. The result of this can be melted

knobs, igniters and increased chance of personal injury.

• Never cook without the drip pan in place and pushed all the way to the back of the Power Burner.

Without the drip pan, hot grease can leak downward creating a fire or explosion hazard.

• Children should not be left alone or unattended in an area where the Power Burner is being used.

Never allow them to sit, stand or play on or around the Power Burner. Do not store items of interest

to children around or below the Power Burner or in the cart. Never allow children to crawl inside of

the cart.

• Do not heat unopened food containers that may cause the container to build-up pressure and burst.

• Never lean over a hot pot or pan while operating Power Burner.

(Safety, cont.)

• When lighting a burner, always pay close attention to what you are doing. Be certain you are de-

pressing the correct igniter button labeled for the burner you intend on using.

• When using the Power Burner do not touch the Power Burner grate or immediate surrounding area

as these areas become extremely hot and could cause burns.

• For proper lighting and performance of the burners keep the ports clean. It is necessary to clean

them periodically for optimum performance. The burners will only operate in one position and must

mounted correctly for safe operation.

• Clean the Power Burner with caution. Avoid steam burns; do not use a wet sponge or cloth to clean

the Power Burner while it is hot. Some cleaners produce noxious fumes or can ignite when applied

to a hot surface.

• INSECT WARNING: Spiders and insects can nest in the burners of this Power Burner and cause the

gas to flow from the a wrong of the burner. This is a very dangerous condition, which can cause a fire

to occur behind the valve panel, thereby damaging the Power Burner and making it unsafe to oper-

ate. Inspect the Power Burner at least twice a year.

• Be sure all Power Burner controls are turned off and the Power Burner is cool before using any type

of aerosol cleaner on or around the Power Burner. The chemical that produces the spraying action

could, in the presence of heat, ignite or cause metal parts to corrode.

• Do not operate the Power Burner under unprotected combustible construction. Use only in well venti-

lated areas. Do not use in buildings, garages, sheds, breezeways or any enclosed areas.

• Keep the area surrounding the Power Burner free from combustible materials, trash, or combustible

fluids and vapors such as gasoline or charcoal lighter fluid. Do not obstruct the flow of combustion

gases and ventilation airways.

• Keep the back of the cart free and clear from debris (cart model).

• If the unit is stored indoors ensure that it is cool. If propane is used, the cylinder must be unhooked

and the propane cylinder stored outside in a well-ventilated area, out of reach of children.

• Never use the Power Burner in windy conditions. If located in a consistently windy area, oceanfront,

mountaintop, etc... a windbreak will be required. Always adhere to the specified clearances.

• Keep any electrical supply cord, away from the heated areas of the Power Burner.

! WARNING

FOR OUTDOOR USE ONLY

NOT TO BE INSTALLED IN OR

ON RECREATIONAL VEHICLES

AND / OR BOATS.

! WARNING

NEVER USE A DENTED OR

RUSTED LIQUID PROPANE

TANK. SHUT OFF TANK WHEN

NOT IN USE.

! AVERTISSEMENT

POUR UTILISATION À

L'EXTÉRIEUR

NE PAS ÊTRE INSTALLÉ DANS OU

SUR DES VÉHICULES RÉCRÉATIFS

ET / OU DES BATEAUX.

! AVERTISSEMENT

N'UTILISEZ JAMAIS DE RÉSERVOIR

DE PROPANE LIQUIDE BOSSELÉ

OU ROUILLÉ. ÉTEINDRE LE RESER-

VOIR LORSQU'IL N'EST PAS UTILI-

SÉ.

LOCATING AND ASSEMBLING THE POWER BURNER:

When determining a suitable location for your Power Burner, take into account concerns such as

exposure to wind, rain, sprinklers, proximity to traffic paths and keeping any gas supply line runs as short

as possible. Locate the Power Burner only in a well-ventilated area. Never locate the Power Burner in a

building, garage, breezeway, shed or other such enclosed areas without an approved ventilation system.

Never locate the Power Burner over, under or next to unprotected combustible construction.

CLEARANCES:

TO NON-COMBUSTIBLE CONSTRUCTIONS:

A minimum of 3” clearance around the Power Burner to non-combustible construction is required to

allow heat to escape freely while cooking.

TO COMBUSTIBLE CONSTRUCTIONS:

This appliance should NOT be located over, under or next to unprotected combustible construction.

ASSEMBLY:

BUILT-IN MODELS: To locate your Artisan™ Power Burner into your Non-combustible enclosure,

complete the following steps:

1. Remove all packaging materials

2. Install and secure the body of the Power Burner to your counter’s enclosure.

3. Ensure that the burners are positioned correctly on their venturi funnels, and are fully

seated onto their supports. (See figure # 1 below)

4. Install the Power Burner Grate.

5. Make the connection to the gas regulator according to the instructions explained on pages

7 through 9 for your gas type.

6. To comply with safety and service requirements, main gas shut off valve must be

accessible from front of Power Burner without using any tools.

Figure # 1

GRATES POWER BURNER

TOP COVER

REGULATOR

LOCATION

LOCK PIN

CART MODELS: Please follow the instructions supplied with the unit in order to mount and connect all

required piping that comes with the unit.

WARNING:

To prevent harm and ensure proper operation of your Power Burner, it is imperative that the burners are

properly installed with respect to the gas orifices. Be certain that the exterior cap and well as internal cap

is inserted completely into the burner’s venture funnel and that the burner rests firmly on its supports.

The burner should not rock side-to-side nor top-to-bottom if properly installed. If excessive burner

movement is present, reseat burner or contact your authorized service provider.

ELECTRICAL REQUIREMENTS:

The ARTP-PB Power Burner is equipped with a high output

electrical ignition system and accent lights on the front panel of

the unit.

The electrical system is designed to be operated at:

115VAC - 50 / 60 Hz.

The unit should be kept plugged into the receptacle (located

under the counter and away from the elements) except when it

is being disconnected for maintenance or troubleshooting (see

page 15).

We recommend using a GFCI Receptacle to maintain proper

grounding and safety at all times.

GAS CONNECTION—LIQUID PROPANE (LP)

NEVER CONNECT THE POWER BURNER TO AN UNREGULATED GAS SUPPLY.

Before proceeding, ensure the unit is fitted for LP gas. Connecting to an improper gas type will result in

poor performance and increased risk of damage or injury. Total gas consumption (per hour) with all

burners set on “HI” is a follows:

• ARTP-PB 52,000 BTUH

The installation of this appliance must conform with local codes or, in the absence of local codes, to the

national fuel gas code, ANSI Z223.1a-1988. Installation in Canada must be in accordance with the

Standard CAN/ CGA-B149.1 Natural Gas Installation or CAN/CGA-B149.2, Propane Installation Code.

Manifold pressure with LP Operating: 10.0” W.C. Non-operating: 11.2” W.C.

L.P. TANK REQUIREMENTS:

Use only a standard 20 Lb. (5 Gal.) propane gas cylinder (18-1/4” H x 12-1/4” Ø). The tank must be

installed in the upright position. Do not use a dented or rusty LP tank as it may be hazardous and should

be checked by your LP supplier. Never use a cylinder with a damaged valve.

The LP gas cylinder must be constructed and marked in accordance with the specifications for LP gas

cylinders of the U.S. Department of Transportation (DOT). The cylinder must be provided with a shut off

valve terminating in an LP gas supply cylinder valve outlet specified, as applicable, for connection type

QCC1 in the standard for compressed gas cylinder valve outlet and inlet connections ANSI/CGA-V-I.

POWER CABLE

(8 FT - 115 V PLUG)

LP GAS CONNECTION TO LP TANKS:

Your Artisan™ Power Burner for use with LP gas comes equipped with its own regulator, which MUST

NOT be removed. There is also a secondary high capacity, hose/regulator assembly for connection to a

standard 20 Lb. LP cylinder. The LP gas pressure regulator and hose supplied with this unit must be

used without alteration.

If this assembly needs to be replaced use only the type specified by Artisan™ for this appliance.

To connect the regulator / hose assembly follow the next steps:

• Locate the regulator and gas connection point in the rear side of your

Power Burner unit .

• Fasten the hose connection to a 1/2” MPT x 3/8” COMP

(compression flare fitting) connected to the elbow. (see Figure # 2).

LP GAS CONNECTION TO LP PIPED SYSTEMS:

An LP piped system is one with a large central LP tank that feeds the entire household. Those systems

are normally equipped with a high pressure regulator by the large LP tank and low pressure regulators

close to the home.

POWER BURNER

UNIT

CONVERTIBLE GAS

PRESSURE REGULATOR

Figure # 2

1/2” FPT X 3/8” FLARE

BRASS FITTING

TYPICAL LP

GAS TANK

LP REGULATOR AND HOSE

ASSEMBLY (PRESET TO 10” WC)

POWER CABLE

(8FT LONG)

!WARNING

KEEP ANY ELECTRICAL CORD

AND FUEL SUPPLY HOSE AWAY

FROM ANY HEATED SURFACES.

! AVERTISSEMENT

GARDER TOUT LE CORDON ÉLECTRIQUE ET LE

TUYAU D'ALIMENTATION DE CARBURANT À

L'ÉGARD DE TOUTES SURFACES CHAUF-

FANTES.

GAS CONNECTION - NATURAL GAS (NG)

NEVER CONNECT THE POWER BURNER TO AN UNREGULATED GAS SUPPLY.

Before proceeding, ensure the unit is fitted for natural gas. Connecting to an improper gas type will result in

poor performance and increased risk of damage or injury. The installation of this appliance must conform with

local codes or, in the absence of local codes, to the national fuel gas code, ANSI Z223.1a-1988. Installation in

Canada must be in accordance with the Standard CAN/ CGA-B149.1 Natural Gas Installation or CAN/CGA-

B149.2, Propane Installation Code.

• ARTP-PB 60,000 BTUH

Manifold pressure with NG: Operating: 5.0” W.C. (.14 PSI)

Non-operating: 5.5” W.C. (.16 PSI)

Optimum pressure: 7.0” W.C. (.25 PSI)

NOTE: To ensure proper heating performance of this appliance, verify that the gas line supply pressure is ad-

equate (7.0” W.C. supply pressure is preferred) to maintain 4.5” W.C. manifold pressure.

Use a minimum 1/2” ID flex hose to prevent gas starvation.

NATURAL GAS CONNECTION:

Ensure that the service pipe supplying the Power Burner is fitted with a shut off valve conveniently positioned

and easily accessible as an emergency gas shutoff.

Your Artisan™ Power Burner for use with Natural Gas comes equipped with its own regulator which MUST

NOT be removed.

If this regulator needs to be replaced use only the type specified by Artisan™ for this appliance.

! CAUTION

CYLINDERS MUST BE STORED OUTDOORS IN A

WELL VENTILATED AREA OUT OF THE REACH OF

CHILDREN.

DISCONNECTED LP CYLINDERS MUST HAVE THREADED

VALVE PLUGS TIGHTLY INSTALLED, AND MUST NOT BE

STORED IN A BUILDING, GARAGE OR ANY OTHER ENCLOSED

AREA. THE GAS MUST BE TURNED OFF AT THE SUPPLY CYL-

INDER WHEN THE UNIT IS NOT IN USE. IF THE APPLIANCE IS

STORED INDOORS, THE CYLINDER MUST BE DISCONNECTED

AND REMOVED FROM THE APPLIANCE.

! WARNING

YOUR ALFRESCO™ AXEVP PRESSURE

REGULATOR HAS A MAXIMUM INPUT

PRESSURE OF 14” WC. (OR APPROX. .5

PSI) , AND A SAFETY LIMIT OF 69” WC.

(2.5 PSI).

! REGULATOR NOTICE

Exposure to pressures above the safety

limit of 69” WC. will permanently damage

the gas regulator requiring a replacement.

OVER PRESSURE DAMAGE IS NOT

COVERED BY YOUR ALFRESCO

! MISE EN GARDE

LE CYLINDRE DOIT ÊTRE STOCKÉ À L'EXTÉRIEUR

DANS UN ENDROIT BIEN VENTILÉ ET HORS DE LA POR-

TÉE DES ENFANTS.

DÉBRANCHER LES BOUTEILLES DE LP DOIVENT

AVOIR DES BOUCHONS DE VALEUR VISSÉS

HERMÉTIQUEMENT INSTALLÉS, ET NE DOIVENT

PAS ÊTRE STOCKÉS DANS UN BÂTIMENT, GARAGE

OU TOUT AUTRE ESPACE FERMÉ. LE GAZ DOIT

ÊTRE ARRÊTÉ AU NIVEAU DU CYLINDRE D'ALIMEN-

! AVERTISSEMENT

VOTRE RÉGULATEUR DE PRESSION AL-

FRESCO GOURMET GRILLADES A UNE

PRESSION D'ENTRÉE MAXIMALE DE 14"

WC (OU ENVIRON 0,5 PSI), ET UNE LIM-

ITE DE SÉCURITÉ DE 69" WC (2,5 PSI).

LEAK TESTING:

GENERAL:

Although all gas connections on your Artisan™ Power Burner are leak tested at the factory prior to ship-

ment, a complete gas tightness check must be performed at the installation site due to possible mishan-

dling in shipment, or excessive pressure unknowingly being applied to the unit.

Periodically check the whole system for leaks, or immediately check if the smell of gas is detected.

TO CONNECT THE PIPING OR HOSE ASSEMBLY FOLLOW THE NEXT STEPS:

• Locate the regulator and gas connection point in the rear side of your Power Burner.

• Connect directly to the regulator by using the existing 1/2” NPT thread at the inlet of the regu-

lator with an appropriate flexible hose ( available at home improvement centers) (see Figure #

• Or alternatively, connect to the regulator with a 1/2” NPT hard pipeline as necessary. (see Fig-

ure # 3).

Figure # 3

CONVERTIBLE GAS

PRESSURE REGULATOR

POWER BURNER

UNIT

SHUT OFF HAND

VALVE

MUST BE LOCATED IN

INCOMING

NG FLEXIBLE

HOSE OR

RIGID PIPE

1/2” NPT CONNECTION

AT REGULATOR POWER CABLE

(8 FT LONG)

! WARNING

ENSURE THAT THE GAS SUPPLY

HOSE DOES NOT COME IN CON-

TACT WITH THE GRILL BODY.

! AVERTISSEMENT

S'ASSURER QUE LE TUYAU D'ALI-

MENTATION EN GAZ N'ENTRE PAS

EN CONTACT AVEC LE CORPS DE

GRIL.

Indice

Altri manuali artisan Bruciatore

artisan

artisan Art-SB1 Guida

Manuali Bruciatore popolari di altre marche

Riello

Riello RS 28/M Guida rapida

True Induction

True Induction TI4B Manuale utente

Weishaupt

Weishaupt WG20 Series Manuale utente

Carolina Cooker

Carolina Cooker M116672 Manuale utente

Riello

Riello RX 500 S/PV Manuale di istruzioni

Unigas

Unigas HTP2000 Manuale utente

baltur

baltur BT 250 DSG 4T Manuale utente

muenkel design

muenkel design round burner Manuale utente

Ecoflam

Ecoflam Multicalor 170.1 Manuale utente

baltur

baltur BT 14 DSGW Manuale utente

Riello

Riello P 140 T/G Guida rapida

AESYS

AESYS TurboFire II Manuale utente

Riello

Riello RG1RKD Guida rapida

IKEA

IKEA GRILLSKÄR Manuale utente

RUSTA

RUSTA SAREK Manuale utente

PROPOINT

PROPOINT 8933657 Manuale utente

baltur

baltur TBL 1000 ME Manuale di riferimento

Riello Burners

Riello Burners P 200 P/G Guida rapida

artisan ARTP-PB Guida

Manuali Bruciatore popolari di altre marche