ASAHI 94 Series Manuale utente
ASAHI/AMERICA, INC 655 ANDOVER STREET LAWRENCE, MA. 01843 TELEPHONE 800-343-3618
Need more detailed information? Download a complete IOM at our website. www.asahi-america.com
File: Series 94 GEN II Modulating User Manual Rev: B 9/30/2015 Page 1 of 4
Series 94 GEN II Modulating Electric Actuator
CAUTION: Proper voltage must be supplied to actuator.
CAUTION: If 120VAC & 220VAC models are PLC driven, output contacts of PLC should be rated at a
minimum of 1.5 times required input voltage of actuator
NOTE: To conform to various electrical codes, a green grounding screw has been installed (on the
baseplate) inside of actuator.
Terminal strip is suitable for up to #14 AWG wire, and should be wired as per the attached diagrams or
the wiring diagram affixed inside of actuator cover.
NOTE: We recommend sealing conduit openings on units installed outdoors or exposed to large
temperature swings (15ºF or more).
We also recommend the heater and thermostat option in these applications.
120 Vac 220 Vac 24 vac Cycle
Time per
90
Degrees
(Seconds)
Weight
(lbs)
Model Torque
(in/lbs)
Amp
Draw
Duty
Cycle
Amp
Draw
Duty
Cycle
Amp
Draw
Duty
Cycle
A94 150 0.5 100% 0.4 100% 4.0 75% 5 3.5
B94 300 0.8 75% 0.6 75% 4.0 75% 5 3.5
Note: Amp rating is considered locked rotor
Duty cycles are for ambient temperature (73°F)
For outdoor or wet locations it is recommended prior to replacing the cover that the top shaft seal be
cleaned and coated with silicone grease. Also clean shaft and lightly coat seal area of shaft with
silicone grease.
Manual Override Operation
Reference Drawing #279QM
Push down on handle (Part #34) and rotate within labeled limits.
To re-engage simply rotate actuator handle in opposite direction until it moves up and re-engages.
CAUTION: The manual override should only be used when there is no power applied to
actuator. When power is restored the actuator will automatically resume normal operation.
Allow 4.75 inches clearance for cover removal.
ASAHI/AMERICA, INC 655 ANDOVER STREET LAWRENCE, MA. 01843 TELEPHONE 800-343-3618
Need more detailed information? Download a complete IOM at our website. www.asahi-america.com
File: Series 94 GEN II Modulating User Manual Rev: B 9/30/2015 Page 2 of 4
QuickCal Procedure
The MODE button selects a particular function, or mode, and the indicator for the selected mode turns on
steady. Pushing the MODE button saves any new setting of the current mode before switching to the next
mode. The adjust up () and adjust down () buttons are used to make adjustments to current mode.
1. Apply power to the actuator on Connector J2: terminal #1 (neutral), terminal #2 (line), and terminal #3
(earth). There is no need for a signal connection during calibration.
2. Push the MODE button until the yellow “MANUAL/FB POT CAL” LED is illuminated. The LED may be
flashing (at different speeds) through the next several steps. This is expected and will be explained.
3. Use the adjust buttons ( and ) to move the actuator and verify that the limit switches are set past the
desired open and closed positions; then move the actuator to mid stroke.
4. If LED is solid, proceed to step 7.
5. If LED is flashing, loosen the gear on the actuator shaft and rotate the potentiometer gear until the LED is
no longer flashing, but on solid - this indicates the center of the potentiometer’s travel. Note that the LED will
flash at a slower rate the farther away from the mid position it gets. Once the LED is on solid tighten all gears.
6. Push the MODE button until the “CLOSE” LED is illuminated. Use the adjust buttons ( and ) to drive the
actuator to the desired closed position. Ensure that the close limit switch does not engage.
7. Push the MODE button until the “OPEN” LED is illuminated. Use the adjust buttons ( and ) to drive the
actuator to the desired open position. Ensure that the open limit switch does not engage.
8. Please skip to Aux Open/Close Setup if optional Transmitter with Relays is installed; otherwise continue
to the next step.
9. Push the MODE button until the “COMMAND TYPE” LED is illuminated. Use the adjust buttons ( and )
to select appropriate input signal (4-20mA, 1-5VDC, 0-5VDC, 0-10VDC, 2-10VDC or Digital). If 0-5VDC or 0-
10VDC is selected, the LOSS OF COMMAND feature is not available, so proceed to step 12.
10. Push the MODE button until the “LOSS OF COMMAND” LED is illuminated; this sets the actuator to a
predetermined position upon loss of command. Use the adjust buttons ( and ) to select appropriate position
(OPEN, CLOSE, or LAST POSITION).
11. Please skip to Aux Position Setup if optional Transmitter, or optional Transmitter with Switches is
installed, otherwise continue to the next step.
12. Push the MODE button until the “AUTO” LED is illuminated. Your calibration is now COMPLETE. Connect
the command signal wires to connector J2: terminal #4 (signal ground) and terminal #5 (mA input) OR
terminal #6 (voltage input), depending on the application. If a signal input was already connected, the actuator
should have moved to that position.
Aux Open/Close Option Setup
1. Push the MODE button until the “AUX CLOSE OUTPUT” LED is illuminated. Use the adjust buttons (
and ) to drive the actuator to the desired auxiliary close position.
2. Push the MODE button until the “AUX OPEN OUTPUT” LED is on. Use the adjust buttons ( and ) to
drive the actuator to the desired auxiliary open position.
3. Continue with Step 9 in the Quick Calibration Procedure (see above).
Aux Position Option Setup
1. Push the MODE button until the green “AUX POSITION OUT CAL” LED illuminates while the “CLOSE”
LED flashes.
2. Use the adjust buttons ( and ) to set the desired output voltage or current (mA) on the option module
output for the closed position.
3. Push the MODE button so the “AUX POSITION OUT CAL” LED remains steady while the “OPEN” LED
flashes. Use the adjust buttons ( and ) to set the desired output voltage or current (mA) on the option
module output for the open position.
Continue with Step 12 in the Quick Calibration Procedure (see above).
ASAHI/AMERICA, INC 655 ANDOVER STREET LAWRENCE, MA. 01843 TELEPHONE 800-343-3618
Need more detailed information? Download a complete IOM at our website. www.asahi-america.com
File: Series 94 GEN II Modulating User Manual Rev: B 9/30/2015 Page 3 of 4
ASAHI/AMERICA, INC 655 ANDOVER STREET LAWRENCE, MA. 01843 TELEPHONE 800-343-3618
Need more detailed information? Download a complete IOM at our website. www.asahi-america.com
File: Series 94 GEN II Modulating User Manual Rev: B 9/30/2015 Page 4 of 4
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali ASAHI Controllori
