ASCHER RACING F28-SC Manuale utente
F28-SC
product manual
V1.1
steering wheel for racing simulators
Ascher Racing GmbH 1
1. general information 3
2. Quick Release mounting 4
3. initial operation 9
4. general operation 10
5. button label application 11
6. paddle shifter force setting 12
7. dimensions 13
8. wiring schematic 14
table of contents
2
•wireless formula steering wheel for Simucube 1 & 2
•285mm diameter
•mass: 1000 g
•3,6 V lithium battery (ER 14250)
•standard 6 x 70mm bolt pattern (M5 threaded) to mount quick release
•28 inputs in total
•grips covered in original ALCANTARA®
•do not apply excessive force on the antenna; handle with care (e.g. laying wheel on a table)
•package contents:
–F28-SC steering wheel
–alternative magnets & spacers for paddle shifters (see foam insert)
–bolts and washers to mount standard Quick Release (such as Q1R)
–button labels sheets (black and white)
1. general information
3
1. SQR wheel side via standard SC2 adapters
2. SQR wheel side via Ascher Racing SQR 70mm Adapter
3. Q1R 70mm wheel side
4. QRs with M5 threads
2. Quick Release mounting
4
2.1 SQR wheel side via standard SC2
adapters
SQR wheel side
SQR 30mm spacer
SQR 70mm adapter
5
2.2 SQR wheel side via Ascher Racing
SQR 70mm Adapter
6
2.3 Q1R 70mm wheel side
7
•not as straight forward as previous QRs due to both parts being M5 threaded
•M5 threads of one part need to be bypassed using captive screws
•through hole M5 threaded QRs (e.g. HRS Xero Play QR) bypass the QR part
•blind hole M5 threaded QRs (e.g. NRG) use captive screws from inside the wheel casing
1. open wheel rim by removing 7 x front plate bolts (2.5mm allen key)
2. screw in 5 x captive screws completely until threads do not intersect anymore
3. attach QR by turning each bolt ¼ turn in a circular pattern
4. attach front plate – make sure not to squeeze shifter cables
2.4 QRs with M5 threads
8
•open True Drive/ Simucube Configuration Tool go to Simucube Wireless Wheels tab
•set checkmark: Connect automatically to paired devices
•switch on steering wheel (ON-OFF switch on the rear side)
•double click Ascher Racing F28
•wheel is now paired, connected and shows up in the Overview tab
•check connection signal quality (Overview tab) for a full rotation of the steering wheel
•signal quality must be above 20% at all times for perfect operation
3. initial operation
9
•when switched ON, the wheel will go into discovery mode for 30s (blinking LED)
•if Simucube is switched on, it connects automatically and shows up in the Overview tab
•LED will indicate successful connection by blinking three times
•SC2 will indicate connection/ disconnection by an audible beep (if checked in the Hardware
Settings tab)
•alternative connection:
–pull both paddle shifters simultaneously to connect immediately
–pull both paddle shifters simultaneously for 5s to disconnect
•after driving session, it is recommended to switch-off/ disconnect the wheel to avoid
constant battery drain in specific circumstances when a connection to SC is active
•expected battery life of 2 - 3 years on heavy daily usage
•low battery voltage: True Drive will show a warning message, SC2 will play an audible beep
•remaining energy will still last for many days to have time for replacing the battery
•to swap batteries, open access window on the rear side (1.5mm allen key required)
4. general operation
10
Indice
Altri manuali ASCHER RACING Controller per videogiochi
