ASCOM TeleCARE SB Manuale utente

TD 92345GB

Installation Instructions

teleCARE M

Pull Cord Switch Module

Wall mounting

2005-06-16 / Ver. A Details subject to change without notice

123

4567

TD 92345GB

Installation Instructions

teleCARE M

Pull Cord Switch Module

Ceiling mounting

2005-06-16 / Ver. A Details subject to change without notice

123

4 5 6

TD 92345GB

Installation Instructions

teleCARE M Pull Cord Switch Module

2005-06-16 / Ver. A Details subject to change without notice

Mounting the backplate

When mounting the backplate on an

uneven surface, be sure not to bend

the backplate. Just use enough

pressure to tighten the screws without

bending the backplate.

Attaching the pull-cord module

Step 1: Place the bottom of the switch

module over the lower snap fittings of

the backplate.

Step 2: Hold the bottom of the switch

module in place while moving the top

towards the backplate until it locks

onto the upper snap fittings.

Because the pull-cord module is snap

fitted on top of the backplate, it is

possible that when excessive force is

used, the pull-cord module can be

pulled off of the backplate just before

the safety brake balls come apart. To

minimize the risk of pulling it off,

make sure that the backplate is

mounted straight.

TD 92345GB

Installation Instructions

teleCARE M Pull Cord Switch Module

2005-06-16 / Ver. A Details subject to change without notice

TD 92345GB

Installation Instructions

teleCARE M Pull Cord Switch Module

2005-06-16 / Ver. A Details subject to change without notice

Pull Cord Switch Module Programming

Solder Pad Settings

TD 92345GB

Installation Instructions

teleCARE M Pull Cord Switch Module

2005-06-16 / Ver. A Details subject to change without notice

Positioning of the teleCARE Peripherals

TD 92345GB

Installation Instructions

teleCARE M Pull Cord Switch Module

2005-06-16 / Ver. A Details subject to change without notice

teleCARE Switch Module

Dismantling Instructions

To remove the face plate of the teleCARE switch modules

a screwdriver with a point of approximately 6mm wide is

to be used.

Insert the point of the screw-

driver into the groove at the

side of the switch module,

between the face plate and

the backplate (or surface

mounting frame) at about

10mm from one of the top

corners.

Gently push and turn the screw driver until

the faceplate releases from the backplate.

Questo manuale è adatto per i seguenti modelli

Altri manuali ASCOM Sistema di sicurezza

ASCOM

ASCOM AMC Manuale utente

ASCOM

ASCOM teleCOURIER 914D Manuale utente

ASCOM

ASCOM U971 Manuale utente

ASCOM

ASCOM telePROTECT 900 Guida utente

ASCOM

ASCOM A71 - 1 Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente

ASCOM teleCARE SB Manuale utente

Manuali Sistema di sicurezza popolari di altre marche