Ashford Jack Loom Manuale utente

INSTRUCTIONS

Ashford Guarantee

Thank you for purchasing this Ashford product. In the unlikely event there is any

fault in manufacture we will replace the item. To validate our guarantee please

visit our website or write to us.

Ashford Handicrafts Limited

Factory and Showroom: 415 West Street

PO Box 474, Ashburton, 7700 New Zealand

Telephone 64 3 308 9087 Facsimile 64 3 308 8664

Email: sal[email protected]o.nz Internet: www.ashford.co.nz

JL90ES140618V5

Jack Loom

8 Shaft - 97cm (38ins)

Finishing the wood

The Sliver Beech tree is a native of New Zealand and has a lovely variety of colour and grain.

This Jack Loom has been ﬁnished with a water based lacquer to protect the kiln dried timber from climatic changes and enhance its

natural character. To repair and restore the ﬁnish use Ashford Wax Polish to enhance the natural beauty of the wood.

Before Assembly

• Please read these instructions from beginning to end, identify all parts and hardware and understand the assembly sequence.

• BOLTS. Check and sort the sizes and quantities against the full-size drawing on page 4.

• Rub candlewax on the threads of the wood screws to make assembly easier.

Check hardware against full

size illustration.

To make assembly easier use

candle wax on the screws.

ASSEMBLY INSTRUCTIONS FOR

THE ASHFORD JACK LOOM

Tools Required

Hints

More Information

The Wheel Magazine

Ashford’s annual ﬁbrecraft magazine.

Spinning, weaving, felting, dyeing and

knitting projects, patterns and articles

from around the world. To receive

the glossy version delivered to you,

subscribe at:

www.ashford.co.nz/subscribe

How-to videos on You Tube

Watch our how-to videos on You Tube.

www.youtube.com/user/AshfordHandicrafts

Facebook

Join us on facebook.

www.facebook.com/ashford.wheels.looms

Spanner

Candle wax Wood glue Oil

Screwdriver, hammer, candlewax, wood glue, light lubrication oil, adjustable spanner and a ruler.

OVERVIEW

HARDWARE CHECKLIST

1 – M8 x 50 Hex Head Bolt

6 – M6 x 80 Hex Head Bolt

2 – M6 x 100 Hex Head Bolt

2 – M6 x 65 Hex Head Bolt

1 – M8 x 100 Cup Head Bolt

4 – M6 x 50 Cup Head Bolt

1 – M6 x 40 Cup Head Bolt

9 – M6 x 65 Cup Head Bolt

2 – M6 x 75 Cup Head Bolt

3 – M6 x 70 Cup Head Bolt

28 – M6 X 16 Washer

6 – M6 x 22 Washer

1 – M8 x 19 Washer

48 – M8 x 25 Washer

8 – 8 x 2 Screw

2 – 45mm Clip Rings

8 – 8 x 1 ½ Screw

1 – 12 x 1 Pan Head Screw

2 – 6 x ½ Pan Head Screw

1 – M11 x 4 Brass Spacer

1 – 6.5 x 40 Cotter Pin

3 – 50mm Screw Hook

1 – M8 Hex Nut

1 – M10 Hex Nut

1 – M8 Nylock Nut

15 – M6 Nylock Nut

16 – M11 Rubber Buffer

2 – M16 Rubber Buffer

20 – 3/32 Dome Caps (4 spares)

10 – M6 Barrel Nut

2 – M10 Spanner

1 – M13 Spanner

6 – M6 Nylon Knob

101 – Texsolv Straight Peg

16 – Harness Hook

1 – Heddle Hook - Double ended

1 – Heddle Hook - Metal

80 – Texsolv Treadle Cord 30cm

14 – Texsolv Warping Cord 80cm

8 – Texsolv Heddles 268, bundles of 100

6 – M8 x 170 Steel Rods - Lever Assembly

2 – 5/8 x 75 Steel Shaft - Cloth beam and

Warp Roller

2 – M6 x 180 Threaded Rod with Dome Nut

REAL SCALE HARDWARE

10 – M6 Barrel Nut

8 – 8 x 1½ Screw

1 – 12 x 1 Pan Head Screw

1 – M10 Hex Nut

1 – M8 x 19 Washer

1 – M8 Nylock Nut

48 – M8 x 25 Washer

6 – M6 x 22 Washer

15 – M6 Nylock Nut

1 – M8 x 100 Cup Head Bolt

8 – 8 x 2 Screw

1 – M8 Hex Nut

20 – 3/32 Dome Cap

1 – 6.5 x 40 Cotter Pin

2 – M16 Rubber Buffer

16 – M11 Rubber Buffer

2 – 6 x ½ Pan Head Screw

9 – M6 x 65 Cup Head Bolt

1 – M8 x 50 Hex Head Bolt

6 – M6 x 80 Hex Head Bolt

2 – M6 x 65 Hex Head Bolt

2 – M6 x 100 Hex Head Bolt

4 – M6 x 50 Cup Head Bolt

1 – M6 x 40 Cup Head Bolt

2 – M6 x 75 Cup Head Bolt

3 – M6 x 70 Cup Head Bolt

28 – M6 X 16 Washer

1 – M11 x 4 Brass Spacer

101 – Texsolv Straight Peg 16 – Harness Hook

6 – M8 x 170 Steel Rod

2 – 45mm Clip Ring

2 – 5/8 x 75 Steel Rod

3 – 50mm Screw Hook

PARTS

M6 Barrel Nut

M6 X 16 Washer

M6 x 80 Hex Head Bolt

ASSEMBLY OF THE LOOM

1. Assemble the base using M6 x 80 Hex Head Bolt, M6 X 16 Washer and M6 Barrel Nut. Note: The holes in rail BX are to the top.

Nylon bushes in parts Cand CX are on the inside.

2. Bolt castle side Eto the outside of base

rail A, and the castle side EX to the base

rail AX using M6 x 65 Cup Head Bolts, M6

X 16 Washer and M6 Hex Nut. Note: The

nylon shaft guides are to the inside of

the frame and holes for the beater stops

face forward.

3. Secure the blocks Oto the inside of the

castle sides Eand EX with M6 x 65 Cup

Head Bolts, M6 X 16 Washer and M6 Nylock

Nuts. Tap in with a hammer.

Note: The rubber buffer is to the top.

4. Secure one rail Mto blocks O

using two 8 x 2 Screws at each end.

Note the position of the holes for

the steel rods x.

5. Place the six M8 x 170 Steel Rods

into the rail M.

M6 x 65 Cup

Head Bolt

M6 x 65 Cup

Head Bolt

M6 x 16

Washers

M6 Nylock Nut

M6 x 16

Washers

M6 Nylock Nut

8 x 2 Screws

M8 x 170 Steel Rods

TAP IN WITH

A HAMMER

TAP IN WITH

A HAMMER

Back Rail M Lever Assembly N

M8 x 25 Washers

N NN N N N N N

M6 x 80

Hex Head

Bolt

M6 x 16

Washer

M6 Barrel

Nut

M6 Barrel

Nut

6. Apply a drop of oil onto the two lower steel rods. Then slide 5 x M8 x 25 washers onto the two lower steel rods followed

by a lever assembly N. Place two washers onto each lower steel rod followed by another lever assembly N. Repeat this

procedure until all the lever assemblies are in position, ﬁnishing with 5 washers.

7. Locate the second rail Monto the steel rods and secure to blocks Ousing two 8 x 2 Screws at each end.

8. Identify the cloth beam supports F(left) and FX (right). FX has a counter-bored hole on the outside.

9. Attach but do not tighten FX to DX with a M6 x 80 Hex Head Bolt, M6 X 16 Washer and M6 Barrel Nut and attach to EX with the M6 x

180 Threaded Rod with Dome Nut and M6 X 16 Washer. Repeat for the opposite side with F, Dand E. Keeping the nylon bushes to

the inside. Note: The nylon bushes are towards the rear.

10. Slide the ratchet lever Gonto the steel shaft on the cloth beam Hand ensure the pawl engages the ratchet teeth.

11. Twist the cloth beam support FX up slightly and locate the cloth beam Hinto the nylon bush. Lower Hso the holes in Hand F

line up and then carefully tap a 5/8 x 75 Steel Shaft through the nylon bush and into H. Then tighten the bolts securing Fand

FX.

M6 x 16

Washer

M6 x 180 Threaded Rod

and Dome Nut

12. Insert the 12 x 1 Pan Head Screw into the inside of the front upright DX for a ratchet lever stop. When transporting the loom lift

and pull the lever sideways, then let it hang down.

13. Attach the ratchet dog to the right cloth beam support FX using a M8 x 50 Hex Head Bolt, M10 Hex Nut, M8 x 19 Washer and M8

Nylock Nut. Tap the head of the bolt into the counter-bored hole. Do not overtighten as the dog should move freely after

tightening the nut.

12 x 1 Pan

Head Screw

M10 Hex Nut

M8 x 50 Hex

Head Bolt

M8 x 19

Washer

M8 Nylock

Nut

TAP IN WITH

A HAMMER

14. Slide 5treadles Jonto the steel treadle rod with a round wooden

spacers kbetween. Add the centre block. Then add the next 5

treadles and round wooden spacers followed by the treadle blocks l

at either end. Note that the rod holes in the treadle blocks must be

towards the top. Then bolt all 3 blocks to BX with M6 x 70 Cup Head

Bolt, M6 X 16 Washer, and M6 Nylock Nut. Tap the head into the

wood with a hammer.

15. Push a M6 x 50 Cup Head Bolt through

the inside of back upright CX and tap

the head of the bolt into the wood

with a hammer. Then attach spacer P

through the hole with a M6 x 22 Washer

and nylon knob.

16. Push a M6 x 50 Cup Head Bolt through

the inside of castle side EX and tap the

head of the bolt into the wood with a

hammer. Locate the slot in spacer P

onto the bolt and secure with a M6 x 22

Washer and nylon knob. Repeat for the

other side.

Note: The middle slot is used to hold

the back beam in the closed position.

Steel Rod

M6 x 70 Cup

Head Bolt

M6 x 70 Cup

Head Bolt

M6 x 70 Cup

Head Bolt

M6 Nylock

Nut

M6 x 16

Washer

M6 x 16

Washer

M6 Nylock

Nut

M6 x 70 Cup

Head Bolt

M6 x 50 Cup

Head Bolt

M6 x 50 Cup

Head Bolt

TAP IN WITH

A HAMMER

M6 x 22

Washer

M6 x 22

Washer Nylon Knob

Nylon Knob

TAP IN WITH

A HAMMER

TAP IN WITH

A HAMMER

Indice

Altri manuali Ashford Ruota che gira

Ashford

Ashford e-Spinner Super Jumbo Manuale utente

Ashford

Ashford TDSW04072014V9 Manuale utente

Ashford

Ashford e-Spinner 3 Manuale utente

Ashford

Ashford YARN STAND 6 Manuale utente

Ashford

Ashford TRAVELLER Manuale utente

Ashford

Ashford e-Spinner 3 Manuale utente

Ashford

Ashford TDSW110618V11 Manuale utente

Ashford

Ashford KIWI 2 SPINNING WHEEL Manuale utente

Ashford

Ashford JOY 2 Manuale utente

Ashford

Ashford TRAVELLER 3 Manuale utente

Ashford

Ashford TRAVELLER Manuale utente

Ashford

Ashford TDSW-DDSW10622V3 Manuale utente

Ashford

Ashford COUNTRY SPINNER 2 Manuale utente

Ashford

Ashford INKLETTE LOOM Manuale utente

Ashford

Ashford DOUBLE DRIVE Manuale utente

Ashford

Ashford TDSW-DDSW250722V4 Manuale utente

Ashford

Ashford INKLE LOOM Manuale utente

Manuali Ruota che gira popolari di altre marche

Daedalus

Daedalus Roly-Poly Manuale utente

Kromski

Kromski Polonaise Manuale utente

Schacht

Schacht WOLF PUP LT FL3006 Manuale utente

Schacht

Schacht SPINNING WHEEL WS6502 Guida rapida

Daedalus

Daedalus Magpie V2 Manuale utente

Schacht

Schacht BABY WOLF LOOM Four Treadle Kit Manuale utente

Louet

Louet S10C Manuale utente

Louet

Louet David Istruzioni per il montaggio

Louet

Louet S17 Manuale utente

SpinOlution

SpinOlution Mach III Manuale utente

Louet

Louet David-III Manuale utente

Schacht

Schacht Tapestry Loom Istruzioni per il montaggio

Majacraft

Majacraft Little Gem Manuale utente

SpinOlution

SpinOlution Firefly Manuale utente

Schacht

Schacht ULTRA Manuale utente

SoftWheel

SoftWheel M Series Manuale utente

Schacht

Schacht SIDEKICK SK7770 Guida rapida

Schacht

Schacht LADYBUG Guida all'installazione