Ashford DOUBLE TREADLE KIT Manuale utente

Ashford Guarantee

Thank you for purchasing this Ashford product. In the unlikely event there is

any fault in manufacture, please contact the dealer you purchased it from. To

validate the guarantee, please go to www.ashford.co.nz/product-registration

Ashford Handicrafts Limited

415 West Street, Ashburton 7700, New Zealand

Telephone 64 3 308 9087

sales@ashford.co.nz www.ashford.co.nz

INSTRUCTIONS

DOUBLE TREADLE KIT

for Elizabeth spinning wheel

DTKESW01052015V3

Assembly Sequence

Please read these instructions right through before

commencing.

Finishing the Wood

We recommend the wood surfaces be sealed

before assembly. This protects the kiln dried wood

from climatic changes and enhances its beauty.

Use either the Ashford Wax Finish or the same ﬁn-

ish as the rest of your wheel.

Special Features

Easy to start - no need to use your hands. Just start

treadling. Enjoy comfortable heel and toe action.

New treadling action - the cranks are off set 10 de-

grees so you can start the wheel in either direction.

Good posture - when you use both feet to treadle

your body is naturally in balance.

Less muscle fatigue - the Double Treadle Kit reduc-

es ankle, leg and hip fatigue.

Update kit - your spinning wheel has now been

updated with the new crank and con rod joints for

smooth silent spinning.

ASSEMBLY INSTRUCTIONS FOR DOUBLE TREADLE KIT

FOR ASHFORD ELIZABETH SPINNING WHEEL

Remove the hub pin. Use the nail provid-

ed and a hammer.

Note: on earlier models the hub pin

is in the middle of the hub. Avoid

damaging the spokes. Place a ﬂat

steel object such as pliers or a span-

ner over the nail and hammer it.

Remove from the crank

Take off old conrod from the crank.

the E-clip with a small screwdriver.

the O-ring with a pin or needle

the split pin with a pair of pliers.

Steel object (pliers or a spanner)

Tools Required

philips (pozi)slot or

Remove the crank from the wheel.

Replace the wheel in

position.

Once the hole in the

crank aligns with the slot

in the hub, carefully tap

the 62mm (2 ½”) hub

pin through the hub and

hole in the new crank.

Remove the wheel from the frame. Clean

the bearings and wheel. Remove any

ﬁbres that may have collected around the

crank.

Loosen the screw hold-

ing the rear leg to the

base. Remove the leg

and old treadle rail.

Rub candle wax onto

the steel pins projecting

from the new treadle rail.

Place the Double Treadle

Assembly into position

between the two legs.

Push the rear leg back

into the base and

retighten the screw. Then

sit the wheel back on its

feet.

If your wheel has ball bearing, reassemble as follows.

Short spacer

Hub pin

Long Spacer

Crank

Insert the crank through the bearing in wheel sup-

port F. Slide the long crank spacer onto the crank as

shown.

Then place the wheel into position with the groove

for the hub pin away from the spinner and push the

crank through the hub. Turning the wheel as you

push will make this easier. Stop when the crank to

protrudes about 3mm (⅛”) through the hub.

Then slide the short crank spacer onto the crank.

It is easier if you hold the spacer with a pair of ﬁne

pliers or scissors. Then push the crank through the

hub and into the ball bearing until the hole for the

hub pin aligns with the slot in the hub.

stretch and slide it

into the small slot

and turn it back a ¼

turn until it clicks into

place.

Hold the conrod joint

with one hand on either

side of the treadle rail.

With both hands,

turn the conrod

joint a ¼ turn,

Set the treadle assembly

on the edge of a table.

Insert the conrod joint

on the inside conrod

into the shorter treadle

board.

Then the conrod joint

in the outside conrod

into the large slot in the

longer treadle board.

Note the crank

bearing faces

the back of the

spinning wheel.

Inside

conrod

Outside

conrod

Ashford Handicrafts Limited

415 West Street, Ashburton 7700, New Zealand

Telephone 64 3 308 9087

sales@ashford.co.nz www.ashford.co.nz

Lubricate all moving

parts with Ashford Spin-

ning Wheel Oil.

Slide the inner shell of

the conrod universal

joint onto the crank until

it clicks into the groove.

Then click the outside

conrod onto the univer-

sal joint on the crank.

Now you can enjoy spinning on

your new Ashford Double

Treadle Kit.

If required use the new

drive band to replace

the original.

How to insert the

polyurethane conrod

joints into the conrod.

*This has been pre-

assembled in the factory.

Ashford Spinning Wheel Oil

Altri manuali Ashford Strumenti e accessori per la tessitura

Ashford

Ashford WEAVING FRAME LARGE Manuale utente

Ashford

Ashford RIGID HEDDLE TABLE STAND Manuale utente

Ashford

Ashford WEAVING STARTER KIT Manuale utente

Ashford

Ashford SKEINER 2 Manuale utente

Ashford

Ashford SPINNING WHEEL MAINTENANCE KIT Manuale utente

Ashford

Ashford DOUBLE TREADLE KIT Manuale utente

Ashford

Ashford DOUBLE TREADLE KIT Manuale utente

Ashford

Ashford PACKER BRUSH Manuale utente

Ashford

Ashford TREADLE KIT FOR TABLE LOOM STAND Manuale utente

Ashford

Ashford Wild Carder Manuale utente

Ashford

Ashford KNITTERS LOOM STAND Manuale utente

Ashford

Ashford SampleIt Loom Stand Manuale utente

Ashford

Ashford QUILL SPINDLE Manuale utente

Ashford

Ashford SampleIt Loom Stand Variable Width Manuale utente

Ashford

Ashford TRADITIONAL SPINNING WHEEL Manuale utente

Ashford

Ashford KNITTERS LOOM STAND VARIABLE WIDTH Manuale utente

Ashford

Ashford WEAVING FRAME SMALL Manuale utente

Ashford

Ashford RIGID HEDDLE LOOM STAND Manuale utente

Ashford

Ashford SPINNING CHAIR Manuale utente

Ashford

Ashford TURBO KIT POLYCORD Manuale utente

Ashford

Ashford DOUBLE TREADLE KIT Manuale utente

Ashford

Ashford Lazy Kate Super Jumbo Manuale utente

Ashford

Ashford KNITTERS LOOM SECOND HEDDLE KIT Manuale utente

Ashford

Ashford KIWI 3 SPINNING WHEEL Manuale utente

Manuali Strumenti e accessori per la tessitura popolari di altre marche

Beadalon

Beadalon 216S-100 Manuale utente

BEKA

BEKA Yarn Swift Manuale utente

Beadalon

Beadalon TOGGLE JIG Manuale utente

Toika

Toika Eeva ES Manuale utente

Weaver

Weaver Weaver Snap Davits Manuale utente

Beadalon

Beadalon Ring Weaver Tool Manuale utente

Xiamen Rizheng Industry

Xiamen Rizheng Industry Crochet Hook Kit Set Manuale utente

Read Pleaters

Read Pleaters 24-Row Regular Manuale utente

MOKIDA

MOKIDA ZM2642501SYL-000-000 Manuale utente

Artistic Wire

Artistic Wire Findings Forms 228S-661 Manuale utente