Asko TD25 Manuale utente
Type: TD25
Service manual
This service manual describes tumble dryer type TD25 and is a supplement to the general service manual
for the 700 series.
Contents
Introduction ...................................................................................................................................................3
Product overview ..........................................................................................................................................4
Programme ...................................................................................................................................................5
Indication of programme sequence ...............................................................................................................5
Options and settings .....................................................................................................................................6
Variant settings .............................................................................................................................................7
Test programme ............................................................................................................................................8
Troubleshooting ..........................................................................................................................................10
Components and measurement values ......................................................................................................12
Technical data .............................................................................................................................................13
Wiring diagram............................................................................................................................................14
Appendix: Timer diagram TD25 ......................................................................................................................
Service manual TD25
2
Service manual TD25
3
Introduction
You are holding the service manual for the TD25 generation of tumble dryer.
There are two types of tumble dryer in the TD25 series: TD25.1 and TD25.3. The following page presents
the different versions, to help you identify the machine types. The variants are named differently from mar-
ket to market. The type designation is the most important factor for identifying the machine type. The type
designation can be found on the machine plate, which is located inside the machine’s door.
It should be easy to service a tumble dryer. It is important that you, as a service technician, are given the
conditions to be able to carry out work in an efficient and satisfactory way. Our hope is that this service
manual is a useful tool for your daily work.
Typbeteckning Produktnummer
Löpnummer
År Vecka
Type designa- Product number
Week Serial number
Service manual TD25
4
TD25.3
Programme: 4 automatic programmes, 1 timer programme and 1 airing programme (For further infor-
mation, see the timer diagram at the foot of the document.)
Options: 4 (designations differ depending on the market, see directions for use.)
Settings: Temperature.
2h
min
min
Airin
g
Normal dr
y
Iron dr
y
Dr
y
T
7
5 2
B
U
TTERFLY DRYIN
G
Type overview
TD25.1
Programme: 4 automatic programmes (For further information, see timer diagram at the foot of the
document.)
Options None.
Settings: Temperature.
T712
B
U
TTERFLY DRYIN
G
Program
Temperature
Extra dry
Dry Normal dry
Iron dry
TD25.3
Programme: 4 automatic programmes, 1 timer programme and 1 airing programme (For further infor-
mation, see the timer diagram at the foot of the document.)
Options: 2 (designations differ depending on the market, see directions for use.)
Settings: Temperature.
T
7
3 2
B
U
TTERFLY DRYIN
G
Dr
y
Service manual TD25
5
Programme
When using tumble dryer TD25 it is possible to choose between four different programmes that automati-
cally sense how damp the washing is. The machine dries to different levels depending on which of the four
programmes has been selected on the front panel. The machine only has one automatic programme that
runs for different lengths of time (and therefore dries to different levels) depending on which of the four pro-
grammes has been selected on the front panel. The automatic programme runs for a maximum of 3 hours.
The machine has a Timer programme that runs for the time that is set (20 minutes – 2 hours), regardless of
whether the washing is dry or not.
The machine has an Airing programme that blows cold air for the time that is set (5 minutes – 2 hours).
Indication of programme sequence
During the programme, the current programme sequence is indicated by a fixed light in the LEDs around
the start/stop button (see the image).
The cycle time is calculated during the start sequence.
Note!
If the door is opened whilst a programme is in operation, the programme will be interrupted and return to
the start position.
Start
End
Cooling ¼ cycle time
¾ cycle time ½ cycle time
Service manual TD25
6
Options and settings
Options
2h
Means that the drum will rotate 3 seconds per minute for 2 hours once the drying
programme has finished. The option prevents the fabrics from remaining in the
same position and becoming creased, which is good if you are unable to remove
them immediately after tumble-drying has finished.
If the Buzzer is also activated
a signal will sound each time the drum rotates, as a reminder that the drying pro-
gramme has finished.
5h
Delays the start of the machine by 5 hours.
Activated by pressing the Time-delayed start button and then the start/stop but-
ton.
The number 5 in the display indicates that Time-delayed start has been activated.
The number of hours to start is displayed with a countdown from 5 to 1.
Deactivated by pressing the start/stop button for 3 seconds until the red field next to
Time-delayed start goes out.
This means that a buzzer will sound for 3 seconds when the drying programme
finishes.
Reduces cooling to 3 minutes.
Cannot be used in the Airing programme.
(In ”normal cases” when Short cooling is deselected, the machine cools for 15
minutes. )
Settings
Possible to set to a high or low temperature.
High temperature Low temperature
Airing dryer: 57°C 43°C
Condenser dryer: 73°C 50°C
Temperature setting cannot be carried out in the airing programme.
Service manual TD25
7
Variant settings
The following version settings can be made after replacing the control unit.
Total reset
1. Hold the start/stop button (S1) in, start the machine by pressing the main power switch and keep the
start/stop button depressed until one of the LEDs on the panel lights.
Buzzer
1. Hold S5 or S6 pressed in, start the machine by pressing the main power switch and keep S5/S6
pressed in until L1, L13 and L15 start to flash.
2. Change the setting by pressing J1/S2. L8 lights when the buzzer is activated.
3. Confirm your selection by pressing the start/stop button (S1).
10 A or 16 A
1. Hold the start/stop button (S1) in, start the machine by pressing the main power switch and keep the
start/stop button depressed until one of the LEDs on the panel lights.
2. Press the start/stop button (S1) 5 times. L1 starts to flash.
3. Change the setting by pressing S2 or J1. L8 lights when 16 A is activated.
4. Confirm your selection by pressing the start/stop button (S1).
Adjusting drying time
1. Hold the start/stop button (S1) in, start the machine by pressing the main power switch and keep the
start/stop button depressed until one of the LEDs on the panel lights.
2. Press the start/stop button (S1) for a further 5 seconds until L1 starts to flash.
3. Change the setting by pressing S2 or J1. The selected setting is indicated as follows:
No adjustment: no LED:
+ 5 minutes: L8
+10 minutes: L9
+15 minutes: L10
+20 minutes: L11
4. Confirm your selection by pressing the start/stop button (S1).
The control unit detects and adjusts automatically to the panel layout and machine model when the option
buttons are pressed several times.
L19
L1
L2
L3
L6
L4
L5
L10
L11
L12
L9
L7
L13
L14
L15
a
a
a
a
b
b
b
b
L16
L17
L18
L8
S1
S8 S4S6
S10
S9 S3
S5
S7
J1/S2
Main power switch
S = Push button
L = LED
Service manual TD25
8
Total reset of programmes
To access the test programme, total reset of the programme must be carried out as follows:
1. Cancel the current programme and switch off the machine by pressing the main power switch.
2. Hold the start/stop button (S1) in and start the machine by pressing the main power switch.
3. Check that any of the LEDs around the programme knob (L7 – L12) lights. This indicates that total
reset has been carried out.
Starting the test programme
4. Press button S7 (left-hand button on divided options button) and keep it pressed for approximately 20
seconds.
Note! This must be done within 3 seconds after carrying out total reset.
• All LEDs except L17 and L18 light up continuously. This indicates that the test programme has been
activated.
Testing the motor and condensing waterpump
5. Press the start/stop button (S1).
• LED L6 lights up and is lit for the entire test program-
me.
• Condenser dryer: LED L8 lights up.
• Airing dryer: LED L7 lights up.
• The motor and condensing waterpump starts.
• Water fills the housing for the water tank until the
machine stops (check that the switch for condensation
water works).
6. Press the start/stop button (S1) to start the motor and
pump out the condensation water.
• LED L 2 lights up and is lit for the remainder of the test
programme.
Indication of faults:
Fault indication/symp-
tom Cause
The condensing
waterpump pumps until
S1 is reactivated and
L7 lights up (applies to
airing dryers).
The rear thermistor
does not have any con-
tact or is damaged.
The motor will not start. Motor or cable fault
The condensing water-
pump does not start.
Switch or cable fault
Test programme
The entire test programme is run in a sequence as follows. You can cancel the test programme at any time
during the programme by opening the door or pressing the main power switch.
L19
L1
L2
L3
L6
L4
L5
L10
L11
L12
L9
L7
L13
L14
L15
a
a
a
a
b
b
b
b
L16
L17
L18
L8
S1
S8 S4S6
S10
S9 S3
S5
S7
J1/S2
Main power switch
S = Push button
L = LED
Service manual TD25
9
Testing the element, thermistor and temperature regulation
7. Press the start/stop button (S1).
• LED L3 starts to flash and the large element loop acti-
vates.
8. Press the start/stop button (S1).
• LED L3 lights continuously and the machine runs heat
regulation for 15 minutes.
• LED L4 starts flashing, which means that temperature
regulation is finished.
• Cooling runs for 5 minutes.
• The machine stops.
Indication of faults:
Fault indication/symp-
tom
Cause
The element does not
start.
Element or cable fault
The programme stops.
F9 is shown in the dis-
play (applies to machi-
nes with a display).
The front thermistor is
not connected.
Testing the interval time and buzzer tone
9. Press the start/stop button (S1).
• LED L4 lights up.
• The motor starts and runs at intervals at the same time
as a buzzer sounds.
Indication of faults:
Fault indication/symp-
tom
Cause
No buzzer tone Fault in control
Cancel the test programme.
10. Press the start/stop button (S1).
• The test programme stops and ”End” is shown in the display (applies to machines with a display).
Service manual TD25
10
Troubleshooting
Fault indications
The following faults are indicated by a flashing red light in the start/stop button LEDs and as a trouble code
on the display (display not available on all machine versions).
Fault indication Cause Action
Display LEDs
(flashing)
Meaning
Overfilling
The machine stops.
(applies to condenser
dryers)
The condensation water tank
is full.
Check if the customer has:
• Emptied the tank and
restarted the machine
Condensing waterpump or
hoses blocked.
• Clean hoses and check
voltage and resistance in
the drain pump.
Float/float switch is defective. • Check that the float has
not got “stuck” and check
the function of the micro-
switch.
The control unit is faulty (the
pump does not start).
• Replace control unit.
Maximum permitted pro-
gramme time
The machine stops after 3
hours.
The washing has been spun
at too low a speed, i.e. less
than 800 rpm.
Check if the customer has:
• Tried spinning at a higher
speed
The control unit did not have
chance to reset, but added
the time to the next drying
cycle.
Check if the customer has:
• Has the machine switched
off for 30 minutes before
restarting
High ambient temperature
combined with low element
output and low drying tempe-
rature leads to condensation
formation.
Check if the customer has:
• Attempted to select an-
other programme
• Good ventilation in the
room
Poor condensation due to
blocked external air
• Ensure that the external air
has free passage.
Defective thermistor. • Replace the thermistor.
Defective control unit • Replace control unit.
(no indication in
LEDs)
Thermistor fault
The machine stops.
The front thermistor is de-
fective or the control is not in
contact with it.
• Replace the thermistor.
After carrying out corrective actions as above, reset the fault indications by switching off the machine using
the main power switch.
Altri manuali per TD25
1
Indice
Altri manuali Asko Asciugatrice
Asko
Asko TDC112C Manuale utente
Asko
Asko T721 Manuale utente
Asko
Asko T754 Manuale utente
Asko
Asko T731 Manuale utente
Asko
Asko T702C Manuale di istruzioni
Asko
Asko T720 Manuale utente
Asko
Asko T743 Istruzioni per il montaggio
Asko
Asko T411VD W U Series Manuale utente
Asko
Asko T744C Istruzioni per il montaggio
Asko
Asko T410HD W Series Manuale utente
Asko
Asko T753C Manuale utente
Asko
Asko T783C Manuale di istruzioni
Asko
Asko T701 Manuale utente
Asko
Asko TD70.C Manuale utente
Asko
Asko TDC1781H Manuale utente
Asko
Asko T743 Manuale di istruzioni
Asko
Asko T783C Istruzioni per il montaggio
Asko
Asko T781 Manuale utente
Asko
Asko TD75 Manuale utente
Asko
Asko PROFESSIONAL TDC112HPS Manuale utente
Manuali Asciugatrice popolari di altre marche
Infiniton
Infiniton SD-DG85C Manuale utente
BOMANN
BOMANN WT 5019 Manuale utente
Alliance Laundry Systems
Alliance Laundry Systems TMB795C Manuale utente
Kenmore
Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manuale utente
Frigidaire
Frigidaire CAQE7077KW0 Manuale del proprietario
Bosch
Bosch WTX8HKM9SN Manuale utente