Assa Abloy HES 9400 Istruzioni operative
1
HES 9400/9500/9600/9700
Electric Strike
Installation Instructions and Frame Preparation
Product Components
A 9400/9500/9600/9700 Strike Body
B 9400/9500/9600/9700 Cover
C 1/4"-20 x 1" Mounting Screws
D #10-32 & 10-24 Lockdown Screws (optional)
E #6-32 x 1/4" Cover Screws
F 5/64" Hex Key
G 12-Volt and 24-Volt Pigtails
UL1034
• Static Strength: 1500 lbs
• Dynamic Strength: 70 ft – lbs
• Endurance: 250,000 cycles
UL294 Performance Levels
• Destructive Attack: Level I
• Line Security: Level I
• Endurance: Level IV
• Standby Power: Level I
Electrical Specifications
Electrical Ratings for Solenoid
Continuous Duty 12 VDC 24 VDC
Resistance in Ohms 24 96
mA Continuous Duty 500 250
Solenoids are rated at +/- 10% indicated value.
Minimum Wire Gauge
Requirements
(Based on Round Trip)
Solenoid Voltage
12 VDC 24 VDC
200 feet or less 18 gauge 22 gauge
200 – 300 feet 16 gauge 22 gauge
300 – 400 feet 16 gauge 20 gauge
A
B
C
D
E
F
G
Diagram 1: Product Components
NOTE: Installation wiring for the product and
wiring methods shall be in accordance with the
National Electrical Code, ANSI/NFPA70
2
CAUTION Before connecting any device at the installation site, verify input voltage using a multimeter.
Many power supplies and low voltage transformers operate at higher levels than listed. Any input voltage
exceeding 10% of the solenoid rating may cause severe damage to the unit and will void the warranty.
Preparing the Strike
For 12 VDC, the Plug In Connector (pigtail)
marked “12 VDC” should be used; for 24 VDC,
the pigtail marked “24 VDC” should be used.
1 SELECT the appropriate pigtail that
matches system power and electrically
CONNECT as illustrated in Diagram 1.
2 IF no connector is present,
THEN CONFIGURE the wires
as shown in Diagram 2.
3 IF using the Latchbolt Monitor (LBM)
or Latchbolt Strike Monitor (LBSM),
THEN REFER to Diagrams 5 and 6 to
complete wiring (see page 3).
Verifying the Operation Mode
The HES 9400/9500/9600/9700
Electric Strike is pre-set for FAIL SECURE
OPERATION as shown in Diagram 3.
1 VERIFY that both keepers are in
FAIL SECURE OPERATION.
Converting the Operation Mode
There are two Selector Stop Pins, one on the left
side and one on the right side. Both Selector Stop
Pins must be repositioned (as shown in Diagram
4) to convert the strike to FAIL SAFE OPERATION.
IN FAIL SAFE OPERATION: Both keepers
should be unlocked without power and
locked when power is applied.
1 To convert to FAIL SAFE OPERATION,
REMOVE the Selector Stop Pins on
each side of the strike body using
the provided 5/64" hex key.
2 MOVE the Selector Stop Pins to the FAIL
SAFE OPERATION position (towards the
center of the strike) as shown in Diagram 4.
3 TIGHTEN both Selector Stop Pins after
they have been moved to the FAIL SAFE
OPERATION position using the 5/64” hex key.
Red
Red/green
Black
Violet
Red
Black
Violet
Red/green
(+ 12 VDC)
(- NEG)
(+ 24 VDC)
(- NEG)
or
Electric
Strike
Electric
Strike
Connect
Together
Connect
Together
Connect
Together
Diagram 1: 12V to 24V Conversion Diagram 2: If Connector Is Missing
Selector Stop
Pin Location
Selector Stop
Pin Location
Diagram 3: Fail Secure Operation
Diagram 4: Fail Safe Operation
CAUTION FAIL SAFE OPERATION mode
should not be used in fire rated or windstorm
resistant applications.
3
Preparing the Frame
NOTE: When using a Corbin Russwin Series
5000 or Yale 7000 Series equipped with an
offset deadlatch, the deadlatch is located
just above the vertical alignment line as
shown in the dimesions on page 4.
• IDENTIFY and MARK the latchbolt
centerline on the frame.
• Using the dimensions provided on page
4, MARK all appropriate holes. If using a
HES 9000-ASB*, reference the installation
instructions provided with that product.
NOTE: In retrofit applications this may
require the exit device to shift horizontally
towards the hinge side of the door to
compensate for the HES 9000-ASB.
• PUNCH, DRILL and TAP the
marked holes as required.
* When mounting on an aluminum frame, with a
blade stop, an HES 9000-ASB (sold separately) is
necessary to provide a secure installation. The HES
9000-ASB is shown installed in Diagrams 8 and 9.
Finishing the Installation
• ELECTRICALLY CONNECT the HES
9400/9500/9600/9700 to the Plug In
Connector, and ATTACH the electric
strike to the jamb using the 1/4"-20
x 1"mounting screws provided.
• CHECK the latchbolt interaction with the
keepers to ensure proper engagement
and clearance. If horizontal adjustment is
needed, ADJUST the strike and LOCKDOWN
the horizontal adjustment using the
10-32 set screws illustrated on Diagram 7.
• TIGHTEN the two 1/4"-20 x 1"mounting screws.
• OPTIONAL LOCKDOWN FEATURE: INSTALL
the #10-24 UNC or 10-32 UNF lockdown
screw if additional security is required;
however, REMOVE the strike before drilling
hole. If using a HES 9000-ASB it will require
drilling and tapping of the lockdown hole.
• INSTALL the cover plate, and SECURE in
place using the #6-32 x 1/4"Cover Screws.
Diagram 2: If Connector Is Missing
Diagram 5
Latchbolt Monitor
White Common
Orange Normally Open
Green Normally Closed
Diagram 6
Latchbolt Strike Monitor
Brown Common
Blue Normally Open
Yellow Normally Closed
White
Brown
Orange
Blue
Green
Yellow
Diagram 7
Lockdown
Screw
(optional)
Set Screw
Location
Set Screw
Location
Mounting
Screw
Mounting
Screw
CAUTION IF no LOCKDOWN SCREW is used
the elctric strike WILL NOT be windstorm rated.
This pertains ONLY to the HES 9600 and 9700.
4
HES 9400 Mounted on
Hollow Metal Frame
9"
[228.6mm]
7/8"
[22.5mm]
1-3/4"
[44.5mm]
1-1/16"
[27mm]
4X
7/8"
[22.5mm]
1-5/16"
[33.3mm]
1-5/16"
[33.3mm]
4-1/8"
[104.8mm]
4-1/8"
[104.8mm]
1/2"
[12.7mm]
Clearance
for
LBM/LBSM
Wiring
Centerline
of Latchbolt
This edge
toward
door
Deadlatch Vertical Alignment.
USE this line as a reference to center deadlatch.
See note under “Preparing the Frame” on page 3.
2X
Mounting
Hole
Locations
for
1/4-20 UNC
Mounting
Screws
Final Lockdown Feature 10-32 UNF or
10-24 UNC Screw (optional)
3/4"
[19mm]
Clearance
for Power
Wiring
Frame Preparation
Patent Pending and/or patent www.assaabloydss.com/patents
Copyright © 2019, Hanchett Entry Systems, Inc., an ASSA ABLOY Group
company. All rights reserved. Reproduction in whole or in part without the
express written permission of Hanchett Entry Systems, Inc. is prohibited.
3026006.004 _2
techsupport.esh@assaabloy.com | assaabloyesh.com
800.626.7590 | 10027 S. 51st Street, Ste. 102 Phoenix, AZ 85044 USA
Dimensions
NOTE: Not to scale. For easy installation,
the HES 9000-MTK should be ordered.
Diagram 8
Diagram 9
HES 9000-ASB
(optional)
HES 9400 Mounted on
Aluminum Frame with Blade Stop
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Assa Abloy Serratura della porta
Assa Abloy
Assa Abloy Yale Real Living Assure Lock YRD216-ZW3 Istruzioni di montaggio
Assa Abloy
Assa Abloy Sargent IN220 Manuale utente
Assa Abloy
Assa Abloy Sargent 7800 Series Manuale utente
Assa Abloy
Assa Abloy Valencia Filip Manuale utente
Assa Abloy
Assa Abloy Valencia Hola Manuale utente
Assa Abloy
Assa Abloy CLIQ Manuale utente
Assa Abloy
Assa Abloy UNILOCK LOXURY IX Manuale utente
Assa Abloy
Assa Abloy MSL sFlipLock drive Manuale utente
Assa Abloy
Assa Abloy Rixson 73ER Manuale utente
Assa Abloy
Assa Abloy Sargent Signature Series Manuale utente
Assa Abloy
Assa Abloy Access 3 Manuale utente
Assa Abloy
Assa Abloy Abloy EL648 Manuale utente
Assa Abloy
Assa Abloy Yale nexTouch Specifiche tecniche
Assa Abloy
Assa Abloy Corbin Russwin Access 800 TCAC2 Series Manuale di installazione
Assa Abloy
Assa Abloy Corbin Russwin EcoFlex NAC Series Istruzioni per il montaggio
Assa Abloy
Assa Abloy Code Handle Manuale
Assa Abloy
Assa Abloy v.G1 Sargent Manuale utente
Assa Abloy
Assa Abloy ESA500 Manuale utente
Assa Abloy
Assa Abloy HES 8000 Series Manuale utente
Assa Abloy
Assa Abloy Corbin Russwin ED8400 Series Manuale utente
