Assa Abloy SARGENT IN120 Manuale utente
A8151F
04/16
Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
WiFi
Mortise Lock
Installation Instructions
IN120
1-800-810-WIRE • www.sargentlock.com • A8151F
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
04/30/16
1
2
3
4
5
6
7
Table of Contents
Warning ...................................................................................3
General Description.................................................................4
Specifications ..........................................................................4
System Overview .....................................................................4
Parts Breakdown .....................................................................5
Lock Installation ......................................................................7
Operational Check ................................................................21
Changes or modifications to this device not expressly approved by ASSA ABLOY
could void the user’s authority to operate the equipment.
Warning
1
FCC:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada:
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is
subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements
d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2)
ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.”
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et
d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT
Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When
retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a
code specialist or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.
!
To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when
handling electronic components:
• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces
such as door hinges, latches, and mounting plates especially when mounting electronic components such
as readers and controllers onto the door.
• Leave components (reader and controller) protected in their respective anti-static bags until ready
for installation
• Do not touch pins, leads or solder connections on the circuit boards
4 1-800-810-WIRE • www.sargentlock.com • A8151F
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
04/30/16
IN120 Mortise Lock
Hardware Specifications
General Description
2
3
• Complete lockset with on-board memory
• ADA compliant
• Easily retrofits existing door preps (mortise)
• Latch - Stainless steel
• Optional deadbolt - Hardened steel
• Guardbolt - Stainless steel, non handed
• Handing (RH/RHR/LH/LHR) must be specified,
but is easily field-reversible without opening the
lock case
The IN120 WiFi lock offers the ease and flexibility of WiFi in a streamlined design, setting a new standard
for aesthetics and performance. The IN120 uses IEEE 802.11 WiFi communication and a flexible feature
set for easier, more cost-effective installations, allowing facilities to leverage their IT infrastructure to
expand access control coverage to more doors. Featuring HID®multiCLASS SE®technology, it supports
heightened identity security and multiple credentials, including mobile access.
This product is operated by six (6) “AA” alkaline batteries, or can be hard-powered using an optional
9-24VDC power supply connected by a harness through the door. SARGENT mortise locks are designed
with quality components to provide high security, performance and durability.
Electronic Specifications
4
• WiFi (IEEE 802.11 b/g/n)
• Multiple time zone and holiday access scheduling
• First-in unlock or automatic unlock configuration,
based on specified time schedule
• Support for most advanced wireless encryption
and authentication standards such as WEP, WPA,
WPA2 and 802.1x*
• 2,400 users per lock; 10,000 event audit trail
• Privacy button
• 8200 lock body offers monitoring of deadbolt REX
and provides integrated monitoring of door position
Power requirements:
• Alkaline AA Batteries: 9V, 300mA
• Optional Hard Power
(UL294 Listed Power Supply Required):
9-24VDC, 300mA
*For specific security information, please contact your local
ASSA ABLOY Door Security Solutions sales consultant or
call 800-810-WIRE.
• HID®multiCLASS SE® technology offers support for
the following credentials:
• 2.4 GHz credential compatibility:
• 125 kHz credential compatibilty:
• HID Prox®
• Secure Identity Object™ (SIO) on Mobile
IDs (Bluetooth Smart)
• 13.56 MHz credential compatibility:
• iCLASS®
• iCLASS SE®(SIO-enabled)
• iCLASS Seos®
• SIO on MIFARE® Classic
• SIO on MIFARE® DESfire® EV1
• MIFARE® Classic
• DESfire® EV1
• NFC-enabled mobile phones
• UL 294 Access Control Ratings:
Destructive Attack Level 1
Line Security Level 1
Endurance Level 4
Standby Power Level 1
• UL Listed - UL 294 Indoor Use
• CUL Listed - S319: Class 1
• Case - 12 gauge heavy duty wrought steel
• Cylinder retracts latchbolt (and deadbolt)
• Lock furnished for 1-3/4” doors.
For other thicknesses, consult factory.
• Outside lever controlled by any combination of
contactless reader or mechanical cylinder
• Inside lever retracts both latch and deadbolt
• May be used for indoor and outdoor applications
• ANSI/BHMA A156.25 Listed Grade 1 Compliant
04/30/16
1-800-810-WIRE • www.sargentlock.com • A8151F 5
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
IN120 Mortise Lock
Parts Breakdown
5
1*
5
4
3
2
2a
1* IN-120-EM01-[B]IP-B Reader assembly - black plastic 1
IN-120-EM01-[B]IP-W Reader assembly - white plastic
IN-120-EM01-[B]IP-MB-xxx** Reader assembly - black plastic with metal trim
IN-120-EM01-[B]IP-MW-xxx** Reader assembly - white plastic with metal trim
IN-120-EM01-[B]IPS-B Reader assembly - black plastic
IN-120-EM01-[B]IPS-W Reader assembly - white plastic
IN-120-EM01-[B]CP-B Reader assembly - FeliCa - black plastic
IN-120-EM01-[B]CP-W Reader assembly - FeliCa - white plastic
IN-120-EM01-[B]CP-MB-xxx** Reader assembly - FeliCa - black plastic with metal trim
IN-120-EM01-[B]CP-MW-xxx** Reader assembly - FeliCa - white plastic with metal trim
IN-120-EM01-[B]IPS-MB-xxx** Reader assembly - black plastic with metal trim
IN-120-EM01-[B]IPS-MW-xxx** Reader assembly - white plastic with metal trim
2 IN-120-EM04 Mounting plate assembly 1
2a Through-bolts (#8-32 x 1 1/4”) 2
3 IN-120-EM03 Controller assembly 1
4 N/A AA battery 6
5 IN-120-EM02-B Battery cover assembly - black plastic 1
IN-120-EM02-W Battery cover assembly - white plastic
IN-120-EM02-MB-xxx** Battery cover assembly - black plastic with metal trim
IN-120-EM02-MW-xxx** Battery cover assembly - white plastic with metal trim
** Specify finish
ITEM PART NO./ORDER
STRING DESCRIPTION QTY.
*Specifying Bindicates BLE (Bluetooth) option when ordering
Tools Required:
• #2 Phillips screwdriver
• Flat head screwdriver
• Security allen wrench
6 1-800-810-WIRE • www.sargentlock.com • A8151F
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
04/30/16
IN120 Mortise Lock
Parts Breakdown (Continued)
5
10
6
5
11 3
1
2
10
5
5
5
4
7
8
9**
1 Consult Factory #41 Mortise cylinder 1
2 Consult Factory Cylinder Rosette 1
3 IN-120-7976-hand-fin Lock body with deadbolt with cylinder 1
IN-120-7977-hand-fin Lock body with deadbolt without cylinder
IN-120-7978-hand-fin Lock body without deadbolt with cylinder
IN-120-7979-hand-fin Lock body without deadbolt without cylinder
IN-120-82276-hand-fin* Lock body with deadbolt with cylinder (not shown)
IN-120-82277-hand-fin* Lock body with deadbolt without cylinder (not shown)
IN-120-82278-hand-fin Lock body without deadbolt with cylinder (not shown)
IN-120-82279-hand-fin Lock body without deadbolt without cylinder (not shown)
4 Consult Factory Turn Lever 1
5 82-4355 Trim Pack - Standard levers 1
79-2162 Trim Pack - Deco levers (shown)
6 Consult Factory Inside Rose 1
7 Consult Factory Inside Lever 1
8 79-0035 Lock front - 7900 - Without deadbolt 1
79-0036 Lock front - 7900 - With deadbolt (shown)
82-0578 Lock front - 8200 - Without deadbolt
82-0579 Lock front - 8200 - With deadbolt
9 52-5373 Door Position Switch (DPS) Pack** -not required for 8200 1
10 77-4236 Mortise screw pack - specify finish (includes: wood and metal lock
body screws, faceplate screws, and strike screws)
1
11 Consult Factory Outside Trim 1
12 A8150 Field Prep Template (not shown) 1
13 4713 Door Manufacturers Template (not shown) 1
14 A8151 Instructions (this manual) 1
ITEM
PART NO/ORDER
STRING DESCRIPTION QTY
*Required for Escape Return functionality (a residential requirement in Canada)
5
04/30/16
1-800-810-WIRE • www.sargentlock.com • A8151F 7
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
IN120 Mortise Lock
A. Verify Hand and Bevel of Door
Stand on outside of locked door when determining door hand.
Lock Installation
LH
Left Hand
Hinges Left
Open Inward
LHRB
Left Hand
Reverse Bevel
Hinges Left
Open Outward
RH
Right Hand
Hinges Right
Open Inward
RHRB
Right Hand
Reverse Bevel
Hinges Right
Open Outward
Fig. 1A
1 Prepare Door
6
B. Door Preparation
Prior to installation, all holes must be free of burrs, debris and sharp edges.
Prepare door according to appropriate template (see website www.intelligentopenings.com).
• Field Template: A8150 (ships with product)
• Door Manufacturer’s Template: 4713
Outside Cylinder Hole
(only with cylinder
installation)
Outside of Door Inside of Door
Cable Hole
Lever Holes
Through-bolt Hole
Cable Hole
Inside of Lock body
Wire Hole
Lever Holes
Mortise
Pocket
Thumb Turn Hole
Fig. 1B Wood Door Preparation
External DPS
Hole
Through-bolt Hole
Raceway for Power
(Optional)
(Not required for 8200)
Raceway for Power
(Optional)
8 1-800-810-WIRE • www.sargentlock.com • A8151F
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
04/30/16
IN120 Mortise Lock
2A Prepare 7900 Lock Body*
1. Reverse Lock Hand (If Required)
a. Rotate the latchbolt 180° (Fig. 2A2).
b. Flip deadlatch by hand to match bevel of latchbolt.
2. Reverse Latch Hand (If Required)
Fig. 2A1
Locking piece
Fig. 2A2
Locking piece
Deadlatch
Latchbolt
Red surface of locking piece must face the outside
(locked side) of door.
To rotate locking piece (Fig. 2A1):
a. Position lock body with red surface of
locking piece visible.
b. Insert blade type screwdriver into locking piece slot
to rotate locking piece toward back of lock body.
c. Rotate the locking piece 180° until RED surface is
on opposite side.
Note: Red indicates locked side (outside).
*If 7900 is type of lock being installed
04/30/16
1-800-810-WIRE • www.sargentlock.com • A8151F 9
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
IN120 Mortise Lock
Red surface of locking piece must face the
outside/locked side of door. To rotate locking
piece (Fig. 2B1):
a. Position lock body with red surface
of locking piece visible.
b. Insert blade type screwdriver into
locking piece slot to rotate locking
piece toward back of lock body.
c. Rotate the locking piece 180° until
RED surface is on opposite side.
Note: Red indicates locked side (outside).
Beveled surface of latch must face strike (Fig. 2B2).
The deadlatch is self adjusting.
To change hand of latchbolt:
a. Insert screwdriver into spade (triangular)-
shaped slot.
b. Rotate screwdriver 90º to push latch out
until back of latch clears lock front; then
rotate latch 180º.
Latch will then re-enter lock body.
Note: Latch cannot be unscrewed.
Fig. 2B1
Locking Guide Slot:
Red color indicates
locked side.
Push In
Right Hand
Lock Shown
2B Prepare 8200 Lock Body*
1. Reverse Lock Hand
2. Reverse Latch Hand
Triangular Slot
Latchbolt
Fig. 2B2
*If 8200 is type of lock being installed
10 1-800-810-WIRE • www.sargentlock.com • A8151F
Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
04/30/16
IN120 Mortise Lock
Inside of
Door
3 Install Door Position Switch (DPS)
1. Push wires through raceway toward lock prep.
2. Push DPS firmly into place by hand.
Note: DO NOT TAP SWITCH WITH ANY TOOL.
3. Install magnet into door frame. Push firmly into place by hand.
See instruction A7983.
Fig. 3
Door Position
Switch (DPS)
CAUTION: if DPS is not installed or is installed
improperly, door status monitoring features will
not function.
* Only required with the 7900 lock body.
Altri manuali per SARGENT IN120
1
Indice
Altri manuali Assa Abloy Sistema di interfono
