Assa Abloy HID Signo Biometric Reader 25B Manuale utente
HID®Signo™ Biometric Reader 25B User Guide
HID® Signo™ Biometric Reader 25B
User Guide
PLT-04900, B.2
August 2022
Copyright
© 2022 HID Global Corporation/ASSA ABLOY AB. All rights reserved.
This document may not be reproduced, disseminated or republished in any form without the prior written permission of
HID Global Corporation.
Trademarks
HID GLOBAL, HID, the HID Brick logo, the Chain Design, iCLASS SE, HID Signo, and HID Biometric Manager are
trademarks or registered trademarks of HID Global, ASSA ABLOY AB, or its affiliate(s) in the US and other countries and
may not be used without permission. All other trademarks, service marks, and product or service names are trademarks
or registered trademarks of their respective owners.
Contacts
For technical support, please visit: https://support.hidglobal.com.
What's new
Date Description Revision
August 2022 Updated for HID Biometric Manager version 1.5.1.56 , and Signo Biometric Reader 25B firmware
version 1.0.2000.00019.
B.2
A complete list of revisions is available in Revision history.
PLT-04900, B.2 2 August 2022
Powering
Trusted Identities
HID® Signo™ Biometric Reader 25B
User Guide
HID®Signo™ Biometric Reader 25B User Guide 1
Overview 4
1.1 Overview 5
1.2 Hardware specifications 5
1.2.1 Biometric specifications 5
1.3 Wiring function and color codes 6
1.4 System connections 7
1.4.1 Power supply connection 7
1.4.2 Network connection 7
1.4.3 Standalone operating mode connections 8
1.4.4 Direct connection to PC 8
1.5 Hardware reset the Signo Biometric Reader 25B 9
Fingerprint enrollment guidelines 10
2.1 Fingerprint enrollment guidelines 11
2.2 General guidelines 11
2.3 Fingerprint enrollment best practices for Signo Biometric Reader 25B 13
Acronyms and terminology 14
PLT-04900, B.2 3 August 2022
Powering
Trusted Identities
HID® Signo™ Biometric Reader 25B
User Guide
Section 01
Overview
1.1 Overview
This section provides the HID® Signo™ Biometric Reader 25B wiring functions and color codes, together with system
connection options.
The iCLASS SE® RB25F has been rebranded as the HID Signo Biometric Reader 25B. Both units share the same
hardware.
The device firmware from each service pack release can be applied to either device, however some features are only
applicable to the Signo 25B. They will be called out in the HID Biometric Manager Administration Guide (PLT-04029)
1.2 Hardware specifications
For more detailed information relating to Signo 25B specifications, refer to the Signo 25B product data sheet.
Hardware feature Specification
Mounting Mullion size mounted on door or any flat surface
Dimensions (width x length x depth) 1.93" x 7.95" x 2.17" (4.9 cm x 20.2 cm x 5.5 cm)
Product Weight (g) 13.04 oz (0.38 kg)
Operating Voltage Range (VDC) 12V DC
Operating Temperature -4° F to 153° F (-20° C to 66° C)
Environmental Rating IP67 Indoor/Outdoor and IK09 Impact Ratings
CPU and Memory 64 bit, 1.2 GB, Quad Core CPU. 8GB storage and 1 GB RAM
Panel connection Pigtail, 18" (45.72 cm)
Communications Ethernet (10/100), Wiegand, Open Supervised Device Protocol (OSDP) via RS485
1.2.1 Biometric specifications
Biometric feature Specification
Image resolution / bit depth / Image area 500 dpi / 8 bit, 256 grayscale / 272 x 320 pixels
Template output format ANSI 378 or ISO 19794-2
Supported users on device Up to 250,000 users
1:1 Fingerprint Verification Authentication Max. 50,000 users
1:N Fingerprint Identification Authentication Max. 5,000 users
Card holders Max. 250,000
Events storage 1,000,000
Live Finger Detection Supported
PLT-04900, B.2 5 August 2022
Powering
Trusted Identities
HID® Signo™ Biometric Reader 25B
User Guide
1.3 Wiring function and color codes
The following shows Signo 25B wiring functions and color codes.
Important:
lBond the ground wires between the Signo 25B power supply and the panel power supply.
lThe 19 pigtail wires and Ethernet cable may be cut for wall mounted installation, if required. However, DO NOT
cut the Ethernet cable shorter than 6 inches (15.24 cm). If the reader is installed outdoors, the pigtails must
remain long enough to fit inside the mounting box to meet IP ratings.
WARNING: WIRING THE READER INCORRECTLY MAY CAUSE PERMANENT DAMAGE TO THE READER.
Function group Wire color Function AWG Max. length¹
RS-485
Green RS-485 A
24 4,000 ft
(1,219 m)
Tan RS-485 B
Black RS-485 Ground
Relay
(Reserved for
future use)
Gray Relay - Common
22 500ft
(152 m)
Yellow Relay - Normally Open
Orange Relay - Normally Closed
Inputs
(Reserved for
future use)
Pink REX Input (Supervised)
Gray DPS Input (Supervised)
Black Input Ground
Weigand Port
Green D0
White D1
Brown RED
Orange GREEN
Yellow BUZ
Blue HOLD
Violet TPR
Black Ground
DC Power Red Power +12 V
Black Power Ground
Function group Connector Function Cable Max. length
Network RJ45 socket Ethernet CAT5/5E/6 328 ft(100 m)
lRS-485: Max. bus length: 4,000 ft - 24 AWG (1,219 m)
lMax. length between nodes: 1,640 ft - 24 AWG (500 m)
lInputs: Reserved for controller mode only.
PLT-04900, B.2 6 August 2022
Powering
Trusted Identities
HID® Signo™ Biometric Reader 25B
User Guide
1.4 System connections
1.4.1 Power supply connection
Use a 12V DC power supply capable of at least 2A per device, with IEC/EN 60950-1 approval. If additional power
consuming devices are included, make sure to use a power supply that is able to supply the total power needed for all
connected devices.
Note: It is best practice to use separate power supplies for the Signo 25B and the electric lock.
1.4.2 Network connection
Network connection for a network that has a server or a router configured for DHCP.
PLT-04900, B.2 7 August 2022
Powering
Trusted Identities
HID® Signo™ Biometric Reader 25B
User Guide
1.4.3 Standalone operating mode connections
Signo 25B devices can be used in standalone operating mode.
Note: Limited to SDK partners.
1.4.4 Direct connection to PC
Direct connection to PC using an auto assigned IP address or a static IP address.
Notes:
lIt can take up to five minutes for this connection type to configure.
lSupported network installations can be found in the HIDBiometric Manager Administration Guide (PLT-04029).
PLT-04900, B.2 8 August 2022
Powering
Trusted Identities
HID® Signo™ Biometric Reader 25B
User Guide
1.5 Hardware reset the Signo Biometric Reader 25B
Resetting the Signo 25B device to factory defaults should, where possible, be carried out through the HID Biometric
Manager application. Refer to the HID Biometric Manager Administration Guide (PLT-04029). In the event that
communication between HID Biometric Manager and the Signo 25B is not possible, carry out the following hardware
reset at the reader:
1. Unscrew the installation locking screw from the bottom of the Signo 25B mounting bracket.
2. Slide the Signo 25B upwards and remove from the mounting bracket.
3. From the back of the reader, remove the label that covers the contacts.
4. With power supplied to the reader, short the contacts together using a suitable metal object.
5. Maintain the short for a full five seconds. The Signo 25B will beep while you hold the short.
6. One long beep of two seconds confirms the reset. All device settings will be returned to the default. You will need to
install and update the device in order to return it to the former working level.
PLT-04900, B.2 9 August 2022
Powering
Trusted Identities
HID® Signo™ Biometric Reader 25B
User Guide
Section 02
Fingerprint enrollment guidelines
Indice
Altri manuali Assa Abloy Controllori di accesso IP
