Assa Abloy Interlock Elevation Window Control System Manuale utente
August 2013 ©copyright by ASSA ABLOY
Elevation
Window Control System
Keypad installation and user guide
2
RAIN SENSOR
Read these instructions prior to the activation of the keypad.
Save this user guide in a safe place for future reference.
TOUCH SCREEN ACTIVATION:
Never use sharp instruments, such as a pencil or pen, to press touchscreen keys.
To prevent damage to the screen, always press the touch screen with your fingertip.
CAUTION:
Changes or modifications to this product not approved by ASSA ABLOY could result in warranty being voided.
IMPORTANT:
Correct installation of the network is paramount to the function of the keypad.
Ensure all details are carried out as per the wiring diagram in the installation instructions.
FINISH CARE:
This keypad is designed to provide the highest standard of product quality and performance.
Care should be taken to ensure a long lasting finish. When cleaning is required use a clean, damp,
nonabrasive cloth. The use of lacquer thinners, caustic soaps, abrasive cleaners or polishes for cleaning
may result in damage to this product.
NEED HELP:
For assistance with this product please visit: www.assaabloy.co.nz
Or call on: 0800 NZ LOCKS (0800 69 56257)
WARNINGS
NETWORK ADAPTOR
ACTUATOR
Elevation
Window Control System
INSTALLER - SETUP AND CONFIGURATION
1. Basic Operating Principle 4
2. Powering up the System 4
3. Calibration 4
4. System Setup and Configuration 5-7
a. Allocating Actuators to Zones
b. Checking Zone Allocation
5. Modifying System Configuration 8-10
a. Removing Actuators from Zones
b. Adding Actuators to Zones
6. Restoring Previous Settings 11
7. Rain Sensor Setup 12-17
a. Adding Rain Sensors to Zones
b. Removing Rain Sensors from Zones
c. Configuring Rain Sensor Function
8. Restarting the Keypad 18
9. Trouble Shooting 18
USER GUIDE
10. Home Page 19
11. Selecting A Window Position 20
12. Backlit Home Button 21
13. PIN Code Creation 22
14. Service Details 22
15. System Warnings 23-25
16. Rain Sensor/Actuator Location Matrix 26-27
17. Frequently Asked Questions 28-29
18. Zone Names 29
19. Wiring Diagram 30
20. Notes 31
CONTENTS PAGE
3
INSTALLER - SETUP AND CONFIGURATION
BACKLIT HOME BUTTON
When configuring your network, Actuators are loaded into groups known as Zones.
Multiple Zones are available. Each actuator can only be allocated to one Zone.
BASIC OPERATING PRINCIPLE
Ensure all wiring connections are complete before powering up.
Ideally the Actuators should be powered up before the Keypads. This ensures the Keypads register
all Actuators on the network. If powering up the system is not possible in this manner, and Actuators have not been
recognized, press Restart Keypad in the Setup page. Then proceed to Zone Setup to allocate the Actuators
that have not previously registered.
POWERING UP THE SYSTEM
Once all Actuators are registered the system will proceed to a calibration screen.
Press Calibrate Actuators. All Actuators will move open and close twice.
If a warning is displayed stating ‘Window Obstructed’ this means that an Actuator has performed a safety stop.
Locate this window. Press Home and then Close All. Only the obstructed window will close.
Fix the obstruction. Then press Calibrate Actuators to continue.
CALIBRATION – Ensure there are no obstructions blocking the windows
4
ACTIVE TOUCH SCREEN
An Actuator can only be assigned to one Zone.
This screen will appear once the auto calibration is complete.
Press Yes to commence Zone Setup.
No will take you to the Home page where options of
Open All, Close All, and Setup will be available.
Note: There are a total of 30 Zone names to choose from.
Zone names cannot be customised.
See page 29 for the list of the names.
There are two ways to assign Actuators to zones:
1. If serial numbers are known (from page 26):
If not proceed to section 2 below.
Use the arrow keys to scroll, matching the serial number
on the left with the desired Zone on the right.
Press Add to Zone and confirm your selection.
2. If serial numbers are not known:
Press each Actuator button on the left.
The corresponding Actuator will open.
Note: After 5 minutes it will close automatically.
Visually locate this Actuator. Then use the arrow keys on the right
to select the desired Zone.
Press Add to Zone and confirm your selection.
The window will now close if open.
Note: Pressing the Actuator button again will also close the window.
Repeat either process until all Actuators are allocated to your
desired Zones.
Press Exit & Save then Yes to save your Zone settings.
SYSTEM SETUP AND CONFIGURATION
Allocating Actuators to Zones:
5
6
Method 1.
3. Press any opening position and observe which windows move
to check that the Actuators are assigned to the correct Zones.
Repeat steps 1, 2, and 3 until all Zones have been checked.
SYSTEM SETUP AND CONFIGURATION continued
Checking Zone Allocation:
1. Use the arrow buttons to scroll through the Zone list.
2. Press the zone name, e.g. Lounge 1
Checking Zone Allocation continued:
You can view Zones to see which Actuators have been assigned
to a particular Zone.
1. Press View Zones.
2. Use the appropriate arrow buttons to scroll through either
the Actuator list or the Zone list.
Note: No changes can be made in this screen.
SYSTEM SETUP AND CONFIGURATION continued
Method 2.
7
4. Using the arrow keys on the right, scroll to the Zone from which
you want to remove an Actuator.
5. Press the Actuator button on the left. The corresponding Actuator
will open. Locate this Actuator and check that it is the one you wish
to remove.
6. If it is, press Remove From Zone and confirm your selection
(the Actuator will close automatically when confirmed).
7. If it is not, press the Actuator button again to close this Actuator.
MODIFYING SYSTEM CONFIGURATION
Removing Actuators from Zones:
Note: All Rain Sensors must be removed from a Zone before removing
Actuators from that Zone.
1. From the Home page, press Setup.
2. Press Zone Setup.
3. Press Remove from Zone.
This now takes you to a screen where you can remove Actuators
from Zones.
8
Removing Actuators from Zones continued:
8. Then use the arrow keys to scroll to the next Actuator in the Zone
and repeat the process until the desired Actuator is found.
Note: Actuator locations may have also been previously noted
on pages 26 & 27.
9. Press Setup to exit.
You will not be prompted to save at this point.
The reason for this is explained in the Restore Previous section
(page 11). However you can save if you wish by exiting the
Zone Setup page.
1. Press Zone Setup.
MODIFYING SYSTEM CONFIGURATION continued
Adding Actuators to Zones: Mainly used for modifications to Zone Setups.
9
3. Press the Actuator button on the left.
The corresponding Actuator will open.
4. Locate this Actuator then use the arrow keys on the right
to select the desired Zone.
Once matched press Add to Zone and confirm your selection.
Important: Repeat the process ensuring all Actuators are allocated
to your desired Zones before exiting and saving.
5. Press Exit & Save, and then Yes to save your modified Zone settings.
Note: Serial Number location method can be used if required,
see page 5.
MODIFYING SYSTEM CONFIGURATION continued
Adding Actuators to Zones continued:
2. Press Add To Zone.
This now takes you to a screen where you can add Actuators to Zones.
10
Indice
Altri manuali Assa Abloy Tastiera
Assa Abloy
Assa Abloy Securitron DK-26BK Manuale utente
Assa Abloy
Assa Abloy S series Istruzioni operative
Assa Abloy
Assa Abloy SECURITRON DK-38 Manuale
Assa Abloy
Assa Abloy KP10G77 Manuale utente
Assa Abloy
Assa Abloy Yale Assure Lever YRL226 Specifiche tecniche
Assa Abloy
Assa Abloy Securitron DK-26 Manuale utente
Assa Abloy
Assa Abloy EMTEK LISCIO Manuale utente
Assa Abloy
Assa Abloy Emtek EMPowered Manuale utente
Assa Abloy
Assa Abloy Yale Assure Lever YRL216 Specifiche tecniche
Assa Abloy
Assa Abloy Yale EF Series Manuale utente
Assa Abloy
Assa Abloy DK-16 Manuale utente
Assa Abloy
Assa Abloy Securitron DK-26 Manuale utente
Assa Abloy
Assa Abloy Alarm Controls KP-400 Manuale utente
Assa Abloy
Assa Abloy TRAKA TOUCH S Manuale utente
Assa Abloy
Assa Abloy KESO KEK i-pin Guida utente
Assa Abloy
Assa Abloy Yale SR-PB Manuale utente
Assa Abloy
Assa Abloy Yale SR-KP Manuale utente
