Assurelink HOMEKIT Manuale utente

INSTALLATION

GUIDE

HOME

SMART

ELDERLY

CARE

HOMEKIT

What’s in the box?

×1

Gateway

×1

Temperature &

Humidity Sensor

×2

Door Sensor

×4

Motion Sensor

×1

Network Cable

For gateway

×1

Transmitter

For bedpad

×1

Bed Pad

×24

Velcro Pads

For gateway & sensors

×2

Double-Size Magnet

For door sensor

×1

Power Plug

For gateway

How to Install

1Gateway

Connect network Cable

Connect power Cable

Network

Power Button

RF Signal

Power cable

Reset

Network cable

2Bed Pad

Cover bed pad with a bed sheet

Transmitter cable ON / OFF Switch

Plug transmitter into connector inside bed pad side pocket

Switch on transmitter and ensure red light flashes

Cover transmitter inside side pocket

Press and hold bed pad for at least 15 seconds to

activate transmitter

Place bed pad on a mattress at shoulder or hip level

3Temperature & Humidity Sensor

Slide to open battery cover

Insert 2 AAA batteries

Temperature & humidity sensor should be installed

at a well-ventilated indoor location

Velcro pad

AAA batteries ×2

Wall mount hole

Wall

4Motion Sensor

Slide to open battery cover

Insert 2 AAA batteries

Install motion sensors in living room, kitchen, bathroom

and toilet to cover the areas where most daily

activities occur.

Velcro pad

AAA batteries ×2

Wall mount

hole

Wall

5Door Sensor

Slide to open battery cover

Insert 2 AAA batteries

Install the main part of sensor at the opening side

of the door

Install the small part on the door frame closely to the

main part with less than 1cm distance

AAA batteries ×2

Velcro pad

Double-sized magnet can be used to line up

with the main sensor.

Door Frame

Door

(Inside)

Door Frame

Door

(Inside)

Max Distance<1cm

Where to put

Gateway

Near the Internet port

24 Motion Sensor

In the living room

In the kitchen

In the toilet

In the bathroom

32 Door Sensor

At the main door

At the back door

4Temperature &

Humidity Sensor

Temperature & humidity

sensor should be installed at a

well-ventilated indoor location

5Bed Pad

On the bed

Gateway Reset

Reset

Please follow below steps to reset the gateway if your

App account does not connect.

1Ensure Internet and power cable is connected to

gateway

2Use the end of a paperclip to press the reset button

at the back of gateway

3Press and hold for 5 second to reset the internet and

account setting

4Reconnect Internet and power cable after the

indication light stops flashing

Now, you can retry the normal setup procedures with

an existing or new App account.

Indice

Altri manuali Assurelink Hardware di rete

Assurelink

Assurelink Smart Home Care System Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente