Asus Z62F Manuale utente

Assembly Instructions: ASUS* Z62F

Precaution:

1. Ensure there is no power source connected to the notebook and remove bat-

tery pack. (See Fig.1)

2. Take the necessary steps to minimize risk of electrostatic discharge (ESD).

Removing the Thermal Solution:

1. Remove the panel located on the underside of the notebook, adjacent to the

battery (two screws hold panel in place). (See Fig.2)

2. Loosen the four screws from the thermal solution cooling plate that are lo-

cated on top of the processor.

Note: These screws are smaller than the panel screws. Each screw position is

numbered 1, 2, 3 and 4. Follow this sequence when removing or replacing the

thermal solution.

3. Disconnect the fan cable from the motherboard and remove the two additional

screws located near the heat sink fan. (See Fig.3)

4. When all the screws are detached, remove the thermal solution by lifting the

cooling plate side of the thermal solution slightly upward and then gently pull-

ing the fan side away from the edge of the notebook.

Note: It is recommended that you turn each screw only three revolutions at

a time. For example, when removing the thermal solution, start with screw

number 1 and turn three revolutions counter clockwise. Then move to screw

number 2 and turn three revolutions. Follow the same steps for screw num-

ber 3 and then 4. Repeat this process approximately three times, or until all

screws release from the motherboard. This will ensure that the cooling plate

surface is secured (or removed) evenly across the processor surface.

Securing the Processor:

1. When installing a processor be sure to align pin one of the processor with pin

one on the processor socket. (See Fig.4)

2. Once the processor is properly in place, turn the retention screw 180 degrees

clockwise to secure.

3. Check to ensure that the thermal interface material (TIM) is adequately applied

to the processor. Reapply the TIM if necessary.

4. Replace the thermal solution.

Processor

Fig.1

Fig.2

Fig.3

Fig.4

Assembly Instructions: ASUS* Z62F

5. Important Note: Check to ensure the fan power lead is connected to the

motherboard. (See Fig.5)

6. Replace panel and secure with the same two screws that were previously

removed.

Memory

Precaution:

1. Ensure there is no power source connected to the notebook and remove bat-

tery pack.

2. Take the necessary steps to minimize risk of electrostatic discharge (ESD).

Installing the Memory Module:

1. Remove the small panel located approximately in the middle of the notebooks

underside (two screws hold the panel in place). (See Fig.6)

Note: These screws may be slightly longer than the other panel screws.

2. Insert the module into the socket at a slight angle. (See Fig.7)

3. Ensure that the module is properly seated in socket.

4. Gently press downward so that the module is parallel with socket. The reten-

tion clips should slide into place and secure the memory module.

Removing the Memory Module:

1. Gently press down and slightly outward on the socket retention clips at the

same time with your ngers. This will release the memory module upward.

2. Remove the memory module from the socket at a slight angle.

3. Replace the panel and secure with the same two screws that were previously

removed.

Fig.5

Fig.6

Fig.7

Assembly Instructions: ASUS* Z62F

Hard Drive

Precaution:

1. Ensure there is no power source connected to the notebook and remove the

battery pack.

2. Take the necessary steps to minimize risk of electrostatic discharge (ESD).

Installing the Hard Drive:

1. Remove the hard drive panel located on the bottom surface of the notebook

(three screws hold the panel in place). (See Fig.8)

Note: The screw location for Optical Disk Drive removal or replacement is

located near the center of the bottom surface of the notebook, next to the

memory panel. (See Fig.9)

2. Place the hard drive in the bracket and secure with four screws. (See Fig.10)

3. When the hard drive is properly attached to bracket, turn it upside down and

place in the recessed compartment. Align the hard drive connector to mother-

board connector and slide until securely attached.

4. Secure the panel with the same screws that were previously removed.

Removing the Hard Drive:

1. Gently slide the bracket with the hard drive attached away from the moth-

erboard connector. When the hard drive connector is separated, lift out of

recessed compartment.

Wireless Adapter

Precaution:

1. Ensure there is no power source connected to the notebook and remove bat-

tery pack.

2. Take the necessary steps to minimize risk of electrostatic discharge (ESD).

Installing the Wireless Adapter:

1. Remove the hard drive panel located on the bottom surface of the notebook

(three screws hold the panel in place).

Important Note: It is recommended that a non-conductive material is placed

around the antenna connector leads when not in use. The metal connectors

should not be in direct contact with other system circuitry. This may cause

damage to the system. (See Fig.11)

Fig.8

Fig.9

Fig.10

Fig.11

Assembly Instructions: ASUS* Z62F

2. Insert the adapter into the socket at a slight angle. (See Fig.12)

3. Ensure that the adapter is properly seated in the socket.

4. Gently press downward so that the module is parallel with the socket. The

retention clips should slide into place and secure the adapter.

5. Connect the antenna by attaching the white wire to the connector labeled

“MAIN” and the black wire to the connector labeled “AUX”.

Removing the Wireless Adapter:

1. Remove antenna leads.

2. Gently pull the socket retention clip away from the adapter edge. This will

release the wireless adapter upward.

3. Remove the adapter from the socket at a slight angle.

Keyboard

Precaution:

1. Ensure there is no power source connected to the notebook and remove the

battery pack.

2. Take the necessary steps to minimize risk of electrostatic discharge (ESD).

Installing the Keyboard:

1. Place the keyboard panel upside down of the top of the notebook surface.

(See Fig.13)

2. Locate the FPC ribbon cable connector and ensure the tabs are pulled out.

3. Insert the keyboard FPC ribbon cable into the connector socket and slide the

two connector tabs inward to secure the cable. (See Fig.14)

Note: Because the ribbon cable is very thin, it can be erroneously placed into

a slot above the connector socket. If the cable does not stay in place after in-

serting it into the socket, check to ensure the cable is in the connector socket

and that the connector tabs have been properly engaged.

4. Gently turn the keyboard over and insert the lower edge of keyboard into the

chassis at a slight angle. (See Fig.15)

5. Lower the top edge of the keyboard and gently push the ve latches to se-

cure the keyboard.

Fig.12

Fig.13

Fig.14

Fig.15

Assembly Instructions: ASUS* Z62F

Note: This model may also use two screws to secure the keyboard. Attach

points for the screws would be located in the upper right and the upper left

corners of the keyboard.

Removing the Keyboard:

1. Gently push in the ve latches at the top of the keyboard with a pair of twee-

zers or a single-slotted screwdriver as you slowly lift the keyboard plate up.

2. Place keyboard upside down.

3. Using a pair of tweezers, disengage the connector tabs by gently pulling them

away from the connector.

4. Gently slide the FPC ribbon cable out of the connector socket. (See Fig.16)

Fig.16

Assembly Instructions: ASUS* Z62F

Disclaimers

All boxed Intel products are intended to be professionally installed. This product integration training and the guidance con-

tained herein is provided to Intel customers as a convenience. Intel assumes no responsibility for any errors contained in

this training and has no liabilities or obligations for any damages arising from or in connection with the use of this training

and the guidance contained herein. Intel is not obligated to provide any support or assistance with regard to the informa-

tion provided in this training. Consult all product manufacturer’s documentation before attempting to install or remove

Intel boxed products.

INFORMATION IN THIS PRODUCT INTEGRATION TRAINING IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. EXCEPT

AS PROVIDED IN INTEL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS. INTEL ASSUMES NO LIABILITY WHAT-

SOEVER. AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO SALE AND/OR USE OF INTEL PROD-

UCTS, INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY,

OR INFRINGEMENT OF ANY PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERY RIGHT.

All products, dates, and gures are preliminary and subject to change without notice. Intel may make changes to this train-

ing and product descriptions at any time, without notice. Intel, Pentium, Intel Inside, NetBurst, Centrino, Celeron, the Intel

Inside logo and the Intel logo are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United

States and other countries.

Altri manuali per Z62F

Indice

Manuali Computer portatile popolari di altre marche

HP ze2401xt - Pavilion Notebook PC Manuale utente

Velocity

Velocity NoteMagix M10 Manuale utente

Dell

Dell Alienware 17 R2 Manuale utente

Toshiba

Toshiba A105-S2236 Manuale utente

HP ENVY 17 Manuale

Winbook

Winbook LM Manuale utente

Dell

Dell Inspiron 1464 Manuale utente

Dell

Dell Inspiron 15R 5537 Manuale utente

HP PROBOOK 4520S Manuale

Dell

Dell Latitude ATG D620 Manuale utente

Sony

Sony VAIO PCG-FX270 Manuale utente

Dell

Dell Latitude 7310 Manuale utente

Dell

Dell Precision GU806 Manuale utente

Sony

Sony VAIO PCG-R505JLK Manuale utente

Lenovo

Lenovo THINKPAD X32 Manuale utente

HP Compaq tc4200 Guida rapida

Toshiba

Toshiba mini NB300 Manuale utente

Lenovo

Lenovo ThinkPad X201 Tablet Manuale