Asus RX3041 Manuale utente



RX3041&SL200Internet

ConnectionConfiguration

Guide



V1.0

Contents

Introduction....................................................................................................................1

Chapter 1: Connecting the router...................................................................................1

Chapter 2: Getting to know Internet connection type....................................................1

Chapter 3: Configuring the router..................................................................................2

3.1 Enter into router’s Web-based configuration page..........................................2

3.2 WAN Connection Type ---- Dynamic IP.........................................................3

3.3 WAN Connection Type ---- Static IP..............................................................4

3.4 WAN Connection Type ---- PPPoE.................................................................5

3.5 WAN Connection Type ---- PPTP/L2TP.........................................................6

3.6 WAN Connection Type ---- BigPond..............................................................8

Troubleshooting Tips：.................................................................................................8

Introduction

This document describes how to set up ASUS RX3041/SL200 for getting connection to the

Internet and provides troubleshooting tips to help you fix some simple problems.

Chapter 1: Connecting the router

The figure below illustrates a connection diagram example.

Chapter 2: Getting to know Internet connection type

The router supports following connection types: Automatic IP, Static IP, PPPOE, PPTP, L2TP,

Bigpond

9By default, the Router’s Internet Connection Type is set to Dynamic IP, which should

be kept only if your ISP (Internet Service Provider) supports DHCP (Dynamic Host

Configuration Protocol) or you are connecting through a dynamic IP address.

9If your ISP has assigned you a permanent, fixed (static) IP address for your

computer, select “Static IP”. In this type, you should have a static IP address from

your ISP, and Subnet mask, Gateway IP address are necessary.

9Most of DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to

establish Internet connections, select “PPPOE”. If you are connected to the Internet

through a DSL line, check with your ISP to see if they use PPPoE. In this type, you

should have Username and Password from your ISP.

9Point to Point Tunneling Protocol (PPTP) and Layer 2 Tunneling Protocol (L2TP).

PPTP is a service that usually applies to connections in some European countries

only. In this type, you should have IP address, Subnet mask, Default Gateway,

Username and Password from your ISP.

9BigPond is a service used in Australia only. If you are using a Bigpond connection,

check with your ISP for the necessary setup information.

Chapter 3: Configuring the router

3.1 Enter into router’s Web-based configuration page

a) Open browser and type router’s IP address: http://192.168.1.1 (the default address)

b) Input username and password, both of them: admin (the default value)

c) Click Cancel when show “do you like to start Quick Setup directly” (if you want to use

Quick Setup, please refer to manual or Quick Start Guide’s description).

3.2 WAN Connection Type ---- Dynamic IP

a) Click WAN ÎConnection, Select WAN Connection Mode as Dynamic IP Address.

b) MAC Cloning is optional as your ISP request. If it’s necessary, please enable the MAC

Cloning and fill the MAC of your PC in MAC Address field. Click Clone MAC button will

clone the MAC of current PC automatically.

c) Then click OK to save and apply the setting.

d) Click Continue back to configuration page.

e) Check if the WAN interface gets a dynamic IP address and related information. Click

Status will show WAN information.

3.3 WAN Connection Type ---- Static IP

a) Click WAN ÎConnection, Select WAN Connection Mode as Static IP Address.

b) Configure Static IP Address ÎInput IP Address, Subnet Mask,ISP Gateway provided

by your ISP. MAC Cloning is optional as your ISP request.

c) If your ISP provides more IP addresses, please select Yes for enabling more IP

addresses, and fill More IP Addresses, then click Add button.

d) Then click OK to save and apply the setting.

e) Click Continue back to configuration page.

f) Click Status will show WAN information.

3.4 WAN Connection Type ---- PPPoE

a) Click WANÎConnection,Select WAN Connection Mode as PPPoE.

b) Configure “PPPoE Account”ÎInput Username, Password provided by your ISP

c) Then click OK to save and apply the setting.

d) Click Continue back to configuration page.

e) Check if the WAN interface gets a dynamic IP address and related information. Click

Status will show WAN information.

3.5 WAN Connection Type ---- PPTP/L2TP

a) Click WANÎConnection, Select WAN Connection Mode as PPTP.

b) Select WAN Interface IP ÎDynamic IP

c) Select WAN Interface IP ÎStatic IP, fill IP address, Subnet Mask, Gateway that

provided by your ISP. MAC Cloning is optional as your ISP request.

d) Configure PPTP Account and PPTP Password provided by ISP. And Select the PPTP

Gateway type and fill the gateway info. Connection ID is optional as your ISP request.

e) Then click OK to save and apply the setting.

f) Check if the WAN interface gets a dynamic IP address and related information. Click

Status will show WAN information.

Tip: The setting steps of L2TP are similar as PPTP, please click

WANÎConnection, and select WAN Connection Mode as L2TP.

3.6 WAN Connection Type ---- BigPond

a) If you are using a BigPond connection, check with your ISP for the necessary setup

information.

b) Click WAN ÎConnection, Select WAN Connection Mode as Dynamic IP Address, and

enable BigPond. Fill the User Name, Password and Authentication Server in proper

field.

c) Then click OK to save and apply the setting.

d) Check if the WAN interface gets a dynamic IP address and related information. Click

Status will show WAN information.

Troubleshooting Tips：

Here are some tips for solving simple problems you may have.

Be sure to restart your network in this sequence:

1) Turn off the modem, router, and computer;

2) Turn on the modem, wait for two minutes;

3) Turn on the router and wait for one minute;

4) Turn on the computer.

Make sure the network cables are securely plugged in.

• The WAN indicator on the router lights up if the network cable to the router from the modem

is plugged in securely and the modem and router are turned on.

Altri manuali per RX3041

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Router wireless popolari di altre marche

Milesight

Milesight UG67 Manuale utente

Airlogic

Airlogic AirSync Class 1 Manuale del proprietario

Samsung

Samsung WCH730B Manuale utente

TELEFONICA

TELEFONICA USB Adapter Manuale utente

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manuale utente

Askey

Askey RAC2V1K Manuale utente

Alloy

Alloy WLF2454AP-S Manuale utente

TP-Link

TP-Link TL-WR542G Manuale utente

NETGEAR

NETGEAR WNR2000v4 Manuale utente

Hama

Hama 53120 Manuale utente

Intellinet

Intellinet 524582 Manuale utente

D-Link

D-Link DIR-506L Manuale utente

Sapido

Sapido GR297n Manuale utente

AMTC

AMTC WR7502 Manuale utente

Compaq

Compaq CP-2W - iPAQ Connection Point Manuale utente

SMC Networks

SMC Networks WBR14-N2 FICHE Manuale utente

Draytek

Draytek Vigor2120 Series Manuale utente

Sitecom

Sitecom WLR-4000 Manuale utente