Atag VA63211OT Manuale utente
VA63211OT
User Manual
Dishwasher
Benutzerinformation
Geschirrspüler
CONTENTS
Safety information 2
Safety instructions 3
Product description 5
Control panel 6
Programmes 6
Settings 8
Options 11
Before first use 11
Daily use 13
Hints and tips 14
Care and cleaning 15
Troubleshooting 18
Technical information 21
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
if an incorrect installation and use causes injuries and
damages. Always keep the instructions with the appliance for
future reference.
Children and vulnerable people safety
•This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
•Do not let children play with the appliance.
•Keep all detergents away from children.
•Keep children and pets away from the appliance door when
it is open.
•Cleaning and user maintenance shall not be made by
children without supervision.
General Safety
•This appliance is intended to be used in household and
similar applications such as:
–farm houses; staff kitchen areas in shops, offices and
other working environments;
2
–by clients in hotels, motels, bed & breakfast and other
residential type environments.
•Do not change the specification of this appliance.
•The operating water pressure (minimum and maximum)
must be between 0.5 (0.05) / 8 (0.8) bar (Mpa)
•Obey the maximum number of 15 place settings.
•If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
•Put knives and cutlery with sharp points in the cutlery basket
with the points down or in a horizontal position.
•Do not keep the appliance door open without supervision to
prevent to fall on it.
•Before maintenance, deactivate the appliance and
disconnect the mains plug from the mains socket.
•Do not use water spray and steam to clean the appliance.
•The ventilation openings in the base (if applicable) must not
be obstructed by a carpet.
•The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
SAFETY INSTRUCTIONS
Installation
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Do not install or use the appliance where
the temperature is less than 0 °C.
• Obey the installation instruction supplied
with the appliance.
• Make sure that the appliance is installed
below and adjacent to safe structures.
Electrical connection
WARNING! Risk of fire and
electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information
on the rating plate agrees with the
power supply. If not, contact an
electrician.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by our
Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
3
• This appliance complies with the E.E.C.
Directives.
• Only for UK and Ireland. The appliance
has a 13 amp mains plug. If it is
necessary to change the fuse in the
mains plug, use fuse: 13 amp ASTA (BS
1362).
Water connection
• Make sure not to cause damage to the
water hoses.
• Before you connect the appliance to
new pipes or pipes not used for a long
time, let the water flow until it is clean.
• The first time you use the appliance,
make sure that there is no leakage.
• The water inlet hose has a safety valve
and a sheath with an inner mains cable.
WARNING! Dangerous
voltage.
• If the water inlet hose is damaged,
immediately disconnect the mains plug
from the mains socket. Contact the
Authorised Service Centre to replace the
water inlet hose.
Use
• Do not sit or stand on the open door.
• Dishwasher detergents are dangerous.
Obey the safety instructions on the
detergent packaging.
• Do not drink and play with the water in
the appliance.
• Do not remove the dishes from the
appliance until the programme is
completed. There can be detergent on
the dishes.
• The appliance can release hot steam if
you open the door while a programme
operates.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
Disposal
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
4
PRODUCT DESCRIPTION
54
8
1011 9 67
12
13
23
1
1Top spray arm
2Upper spray arm
3Lower spray arm
4Filters
5Rating plate
6Salt container
7Air vent
8Rinse aid dispenser
9Detergent dispenser
10 Cutlery basket
11 Lower basket
12 Upper basket
13 Cutlery drawer
Beam-on-Floor
The Beam-on-Floor is a light that shows on
the kitchen floor below the appliance door.
• When the programme starts, a red light
comes on and stays on for all the
duration of the programme.
• When the programme is completed, a
green light comes on.
• When the appliance has a malfunction,
the red light flashes.
The Beam-on-Floor goes off
when the appliance is
deactivated.
5
CONTROL PANEL
123456789
1On/off button
2Display
3Delay button
4Program button
5ExtraHygiene button
6TIME SAVER button
7Multitab button
8RESET button
9Indicators
Indicators
Indicator Description
Salt indicator. It is always off while the programme operates.
Rinse aid indicator. It is always off while the programme operates.
PROGRAMMES
Programme Degree of soil
Type of load
Programme phases Options
P1
1)
• Normal soil
• Crockery and
cutlery
• Prewash
• Wash 50 °C
• Rinses
• Dry
• ExtraHygiene
• TIME SAVER
• Multitab
P2
2)
• All
• Crockery, cut-
lery, pots and
pans
• Prewash
• Wash from 45 °C to 70
°C
• Rinses
• Dry
• ExtraHygiene
• Multitab
P3
3)
• Heavy soil
• Crockery, cut-
lery, pots and
pans
• Prewash
• Wash 70 °C
• Rinses
• Dry
• TIME SAVER
• Multitab
6
Programme Degree of soil
Type of load
Programme phases Options
P4 • Normal or light
soil
• Delicate crock-
ery and glass-
ware
• Wash 45 °C
• Rinses
• Dry
• Multitab
P5
4)
• Fresh soil
• Crockery and
cutlery
• Wash 60 °C
• Rinses
• ExtraHygiene
• Multitab
P6
5)
• All • Prewash
P7
6)
• Normal soil
• Crockery and
cutlery
• Prewash
• Wash 50 °C
• Rinses
• Dry
• Multitab
1) With this programme you have the most efficient use of water and energy consumption for crockery and cutlery
with normal soil. (This is the standard programme for test institutes).
2) The appliance senses the degree of soil and the quantity of items in the baskets . It automatically adjusts the tem-
perature and the quantity of water, the energy consumption and the programme duration.
3) This programme has a high temperature rinsing phase for better hygiene results. During the rinsing phase, the
temperature stays at 70 °C for at least 10 minutes.
4) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
5) With this programme you can quickly rinse dishes to prevent remains of food to bond on dishes and odours to
form in the appliance. Do not use detergent with this programme.
6) This is the most silent programme. The pump works at a very low speed to decrease the level of noise. Because
of the low speed, the programme duration is long.
Consumption values
Programme 1) Water
(l)
Energy
(kWh)
Duration
(min)
P1 11 0.961 225
P2 7 - 14 0.6 - 1.6 40 - 160
P3 12.5 - 14.5 1.4 - 1.8 169 - 179
P4 12 - 14 0.7 - 0.9 75 - 85
7
Programme 1) Water
(l)
Energy
(kWh)
Duration
(min)
P5 10 0.9 30
P6 4 0.1 14
P7 9 - 10 1.1 - 1.3 219 - 229
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of
dishes can change the values.
Information for test institutes
For all the necessary information for test
performance, send an email to:
Write down the product number (PNC) that
is on the rating plate.
SETTINGS
Programme selection mode and
user mode
When the appliance is in programme
selection mode it is possible to set a
programme and to enter the user mode.
In user mode, the following settings
can be changed:
• The level of the water softener according
to the water hardness.
• The activation or the deactivation of the
acoustic signal for end of programme.
• The activation or deactivation of the rinse
aid dispenser when you want to use the
Multitab option without rinse aid.
• The level of rinse aid according to the
required dosage.
These settings will be saved until you
change them again.
How to set the programme
selection mode
The appliance is in programme selection
mode when the display shows the
programme number P1.
When you activate the appliance, usually it
is in programme selection mode. However,
if this does not happen, you can set the
programme selection mode in the following
way:
Press and hold RESET until the appliance
is in programme selection mode.
The water softener
The water softener removes minerals from
the water supply, which would have a
detrimental effect on the washing results
and on the appliance.
The higher the content of these minerals,
the harder your water is. Water hardness is
measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in
your area. Your local water authority can
advise you on the hardness of the water in
your area. It is important to set the right
level of the water softener to assure good
washing results.
8
Water hardness
German de-
grees (°dH)
French de-
grees (°fH)
mmol/l Clarke de-
grees
Water softener
level
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5 1 2)
1) Factory setting.
2) Do not use salt at this level.
If you use multi-tablets containing salt and
the hardness of your water is lower than
21°dH, you can set the lowest water
softener level. It deactivates the salt refill
indicator.
If you use standard detergent or multi-
tablets without salt, set the proper
water hardness level to keep the salt
refill indicator active.
How to set the water softener
level
The appliance must be in programme
selection mode.
1. To enter the user mode, press and hold
simultaneously and until the
indicators , , and start to
flash and the display is blank.
2. Press .
• The indicators , and go off.
• The indicator continues to flash.
• The display shows the current
setting: e.g. = level 5.
3. Press again and again to change the
setting.
4. Press the on/off button to confirm the
setting.
The rinse aid dispenser
The rinse aid helps to dry the dishes
without streaks and stains.
The rinse aid is automatically released
during the hot rinse phase.
You can set the released quantity of rinse
aid between level 1 (minimum quantity) and
level 6 (maximum quantity). Level 0 will
deactivate the rinse aid dispenser and no
rinse aid will be released.
Factory setting: level 4.
How to set the rinse aid level
The appliance must be in programme
selection mode.
1. To enter the user mode, press and hold
simultaneously and until the
9
indicators , , and start to
flash and the display is blank.
2. Press .
• The indicators , and go off.
• The indicator continues to flash.
• The display shows the current
setting: e.g. = level 4.
– The levels of rinse aid are from
0A to 6A.
– Level 0 = no rinse aid is
released.
3. Press again and again to change
the setting.
4. Press the on/off button to confirm the
setting.
Use of rinse aid and multi-
tablets
The factory setting of the rinse aid
dispenser is with the dispenser activated.
This means that the rinse aid dispenser
always releases rinse aid.
It is possible to deactivate the rinse aid
dispenser, in this case the dispenser will not
release rinse aid only if the option Multitab
is activated.
If the dispenser is deactivated and you do
not select the option Multitab, the dispenser
will release rinse aid.
The use of the option Multitab with the rinse
aid dispenser deactivated may not give
satisfying drying results.
When the rinse aid dispenser is
deactivated, the rinse aid indicator is always
off when the option Multitab is activated.
How to deactivate the rinse aid
dispenser
The appliance must be in programme
selection mode.
1. To enter the user mode, press and hold
simultaneously and until the
indicators , , and start to
flash and the display is blank.
2. Press .
• The indicators , and go
off.
• The indicator continues to flash.
• The display shows the current
setting: = the rinse aid dispenser
is activated (factory setting).
3. Press to change the setting.
= the rinse aid dispenser is
deactivated.
4. Press the on/off button to confirm the
setting.
Acoustic signals
Acoustic signals sound when a malfunction
of the appliance occurs. It is not possible to
deactivate these acoustic signals.
There is also an acoustic signal that sounds
when the programme is completed. By
default this acoustic signal is deactivated
but it is possible to activate it.
How to activate the acoustic
signal for the end of programme
The appliance must be in programme
selection mode.
1. To enter the user mode, press and hold
simultaneously and until the
indicators , , and start to
flash and the display is blank.
2. Press
•The indicators , and go off.
• The indicator continues to flash.
• The display shows the current
setting: = Acoustic signal off.
3. Press to change the setting.
= Acoustic signal on.
4. Press the on/off button to confirm the
setting.
10
Indice
Lingue:
Altri manuali Atag Lavastoviglie
Atag
Atag DW7114SXB Manuale utente
Atag
Atag VA9811QT Manuale utente
Atag
Atag VA7114RT Manuale utente
Atag
Atag VA7016SRT Manuale utente
Atag
Atag VA6611PT Manuale utente
Atag
Atag VA8018WTC Manuale utente
Atag
Atag DW7214OMB Manuale utente
Atag
Atag VA6011AF Manuale utente
Atag
Atag VA68211TT Manuale utente
Atag
Atag VA6111RT Manuale utente
Atag
Atag VA6311SF Manuale utente
Atag
Atag VA61211KT Manuale utente
Atag
Atag VA71114SRT Manuale utente
Atag
Atag VA9811NT Manuale utente
Atag
Atag VA2113RT Manuale utente
Atag
Atag VA 6511NT/A01 Manuale utente
Atag
Atag DW7113XA Manuale utente
Atag
Atag VA 6411QT/A01 Manuale utente
Atag
Atag VA6611NTUU/A01 Manuale utente
Atag
Atag VA6711PT Manuale utente
